Supero Supero SAS 815TQ Bedienungsanleitung

Rev. 1.0a

SAS 815TQ Backplane

USER'S GUIDE

+5V

GNDGND+12V

I C

+5V +12V +5V +12V

#3 #0

ACT IN

ACT0 ACT1

JTAG UPGRADE JP29:9071 RST JP18:BUZZER RESET

ACT2 ACT3

SIDEBAND

M15

JP10

JP18

J6 J5

JP29

JP44

R144

MH2

M46

J9 J10 JP26

JP47

JP46

JP42

JP33

JP34

JP40 JP51

REV 1.00

SAS815TQ

SUPER

SAS 815TQ Backplane User's Guide

The information in this User’s Manual has been carefully reviewed and is believed to be accurate.

The vendor assumes no responsibility for any inaccuracies that may be contained in this document,

makes no commitment to update or to keep current the information in this manual, or to notify any

person or organization of the updates. Please Note: For the most up-to-date version of

this manual,please see our web site at www.supermicro.com.

SUPERMICRO COMPUTER reserves the right to make changes to the product described in this

manual atany time and without notice. This product, including software, if any, and documenta-

tion may not, in whole or in part, be copied, photocopied, reproduced, translated or reduced to any

medium or machine without prior written consent.

IN NO EVENT WILL SUPERMICRO COMPUTER BE LIABLE FOR DIRECT, INDIRECT, SPECIAL,

INCIDENTAL, SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE

OR INABILITY TO USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE

POSSIBILITY OF SUCH DAMAGES. IN PARTICULAR, THE VENDOR SHALL NOT HAVE

LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE

PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING

OR RECOVERING SUCH HARDWARE, SOFTWARE, OR DATA.

Any disputes arising between manufacturer and customer shall be governed by the laws of Santa

Clara County in the State of California, USA. The State of California, County of Santa Clara shall

be the exclusive venue for the resolution of any such disputes. Supermicro's total liability for all

claims will not exceed the price paid for the hardware product.

Manual Revision 1.0

Release Date: November 1, 2006

Unless you request and receive written permission from SUPER MICRO COMPUTER, you may not

copy or otherwise reproduce/distribute any part of this document.

Information in this document is subject to change without notice. Other products and companies

referred to herein are trademarks or registered trademarks of their respective companies or mark

holders.

Printed in the United States of America

iii

Safety Information and Technical Speciﬁcations

Table of Contents

Chapter 1:Safety Guidelines

1-1 ESD Safety Guidelines .................................................................................... 1-1

1-2 General Safety Guidelines............................................................................... 1-1

1-3 An Important Note to Users............................................................................. 1-1

Chapter 2: JumperSettings and Pin Deﬁnitions

2-1 Front Connectors and Jumpers....................................................................... 2-1

2-2 Front Connector Pin Deﬁnitions ...................................................................... 2-2

2-3 Front Jumper Locations and Pin Deﬁnitions ................................................... 2-4

2-4Rear Connectors and LED Indicators ............................................................ 2-5

SAS 815TQ Backplane User's Guide

Notes

1-1

Safety Information and Technical Speciﬁcations

Chapter 1

Safety Guidelines

To avoid personal injury and property damage, carefully follow all the safety steps

listed below when accessing your system or handling the components.

1-1 ESD Safety Guidelines

Electric Static Discharge (ESD) can damage electronic components. To prevent dam-

age to your system, it is important to handle it very carefully. The following measures

are generally sufﬁcient to protect your equipment from ESD.

• Use a grounded wrist strap designed to prevent static discharge.

• Touch a grounded metal object before removing a component from the antistatic

bag.

• Handle the RAID card by its edges only; do not touch its components, peripheral

chips, memory modules or gold contacts.

• When handling chips or modules, avoid touching their pins.

• Put the card and peripherals back into their antistatic bags when not in use.

1-2 General Safety Guidelines

• Always disconnect power cables before installing or removing any components

from the computer, including the SAS 825TQ Backplane.

• Disconnect the power cable before installing or removing any cables from the

SAS 825TQ Backplane.

• Make sure that the SAS 825TQ Backplane is securely and properly installed

on the motherboard to prevent damage to the system due to power shortage.

1-3 An Important Note to Users

• All images and layouts shown in this user's guide are based upon the latest

PCBRevision available at the time of publishing. The card you have received

may or may not look exactly the same as the graphics shown in this manual.

1-2

SAS 815TQ Backplane User's Guide

Notes

2-1

Safety Information and Technical Speciﬁcations

+5V

GNDGND+12V

I C

+5V +12V +5V +12V

#3 #0

ACT IN

ACT0 ACT1

JTAG UPGRADE JP29:9071RST JP18:BUZZER RESET

ACT2 ACT3

SIDEBAND

M15

JP10

JP18

J6 J5

JP29

JP44

R144

MH2

M46

J9 J10 JP26

JP47

JP46

JP42

JP33

JP34

JP40 JP51

REV 1.00

SAS815TQ

SUPER R

+5V

GNDGND+12V

I C

+5V +12V +5V +12V

#3 #0

ACT IN

ACT0 ACT1

JTAG UPGRADE JP29:9071 RST JP18:BUZZER RESET

ACT2 ACT3

SIDEBAND

M15

JP10

JP18

J6 J5

JP29

JP44

R144

MH2

M46

J9 J10 JP26

JP47

JP46

JP42

JP33

JP34

JP40 JP51

REV 1.00

SAS815TQ

SUPER R

SAS Ports

Front Connectors

Chapter 2

Jumper Settings and Pin Deﬁnitions

2-1 Front Connectors and Jumpers

#1. Power Connectors (4-pin) JP10

#2. CD-ROM/Floppy Drive Power J9 and J10

#3. JTAG JP47

#4. Upgrade Pin JP46

#5. MG9071 Chip

#6. Sideband JP51

#7. I2C Connector JP44

#8. ACT_IN JP26

#9. SAS Port #0 J5

#10. SAS Port #1 J6

#11. SAS Port #2 J7

#12. SAS Port #3 J8

2-2

SAS 815TQ Backplane User's Guide

#4. MG9071 Chip

The MG9071 is anenclosure management

chip that supports the SES-2 controller and

SES-2 protocols.

2-2 Front Connector and PinDeﬁnitions

#3/#4. JTAG Connector andUpgrade Con-

nector

The JTAG connector, designated JP47, and

the Upgrade connector, designated JP46,

are diagnostic purposes. These connectors

should be used a certiﬁedand experienced

technician.

Backplane

Main Power

4-Pin Connector

(JP10)

Pin# Deﬁnition

1 +12V

2 and 3 Ground

4 +5V

#1. Backplane Main Power Connectors

The 4-pin connectors, designated JP10

provide power to the backplane. See the

table on the right for pin deﬁnitions.

#2. CD-ROM/Floppy 4-Pin Connectors

The 4-pin connectors, designated J9 and

J10, provide power to the CD-ROM and

ﬂoppy drives. See the table on the right for

pin deﬁnitions.

CD-ROM/

FDD Power

4-Pin Connector

(J9 and J10)

Pin# Deﬁnition

1 +5V

2 and 3 Ground

4 +12V

2-3

Safety Information and TechnicalSpeciﬁcations

#6. Sideband Headers

The sideband headers are designated

JP51. For SES-2 to work properly, you must

connect an8-pin sideband cable. See the

table to the right for pin deﬁnitions.

Sideband Headers

(JP51)

Pin #Deﬁnition Pin #Deﬁnition

2 Backplane

Addressing

(SB5)

1Controller

ID (SB6)

4Reset(SB4) 3GND (SB2)

6 GND (SB3) 5 SDA (SB1)

8 Backplane

ID (SB7)

7 SCL (SB0)

10 No Connec-

tion

9 No Connec-

tion

#7. I2C Connectors

The I2CConnectors, designatedJP44, are

usedto monitor HDD activity and status. See

the table on the right for pin deﬁnitions.

I2C Connector

Pin Deﬁnitions

(JP44)

Pin# Deﬁnition

1Data

2 Ground

3Clock

4 No Connection

SAS Activity LED Header

Pin Deﬁnitions (JP26)

Pin #Deﬁnition Pin #Deﬁnition

1ACT IN#06 ACT IN#4

2 ACT IN#17 ACT IN#5

3ACT IN#2 8 ACT IN#6

4 ACT IN#39 ACT IN#7

5 Ground 10 Empty

#8. Activity LED Header

The activity LED header, designatedJP26,

is usedto indicate the activity status of each

SAS drive. For the Activity LED Headerto

work properly, connect using a 10-pin LED

cable.

#9-#12. SAS Ports

The SAS ports are usedto connect the SAS

drive cables. The four ports are designated

#0 -#4. Each port is also compatible with

SATAdrives.

2-4

SAS 815TQ BackplaneUser's Guide

JP29

2-3 Front Jumper Locations and Pin Deﬁnitions

Explanation of Jumpers

To modify the operation of the backplane,

jumpers canbe usedto choose between

optionalsettings. Jumpers create shorts

betweentwo pins to change the function

of the connector. Pin 1 is identiﬁedwith

a square solderpadon the printedcircuit

board. Note: On two pin jumpers, "Closed"

means the jumperis on and "Open" means

the jumperis off the pins.

Connector

Pins

Jumper

Setting

3 2 1

321

Jumper Settings

Jumper Jumper Settings Note

JP18Open: Enabled

Closed: Disabled

BuzzerReset

JP29 Open: Default

Closed: Reset

MG 9071 Chip Reset

+5V

GNDGND+12V

I C

+5V +12V +5V +12V

#3 #0

ACT IN

ACT0 ACT1

JTAG UPGRADE JP29:9071 RST JP18:BUZZER RESET

ACT2 ACT3

SIDEBAND

M15

JP10

JP18

J6 J5

JP29

JP44

R144

MH2

M46

J9 J10 JP26

JP47

JP46

JP42

JP33

JP34

JP40 JP51

REV 1.00

SAS815TQ

SUPER R

JP18

I C

ACT IN

ACT0 ACT1 ACT2 ACT3

SIDEBAND

M15

JP44

MH2

M46

JP26

JP42

JP33

JP34

JP40 JP51

JP33

JP34

JP50

JP40

JP42

Inhaltsverzeichnis

Andere Supero Computerhardware Handbücher

Supero

Supero Supero SAS-836TQ Bedienungsanleitung

Supero

Supero SAS 808TQ Bedienungsanleitung

Supero

Supero AOC-SIMSO+ Bedienungsanleitung

Supero

Supero AOC-1UIPMI-B Bedienungsanleitung

Supero

Supero BPN-SAS3-827HQ Backplane Bedienungsanleitung

Supero

Supero AOC-SIM1U Add-on Card Bedienungsanleitung

Supero

Supero BPN-SAS2-216EL1 Bedienungsanleitung

Supero

Supero Supero BPN-SATA-933 BACKPLANE Bedienungsanleitung

Supero

Supero Supero SMT IPMI Bedienungsanleitung

Supero

Supero SAS-827B Bedienungsanleitung

Supero

Supero SAS-837A BACKPLANE Bedienungsanleitung

Supero

Supero Supero SAS-825TQ Bedienungsanleitung

Supero

Supero SAS-216A Bedienungsanleitung

Supero

Supero SAS-747TQ BACKPLANE Bedienungsanleitung

Supero

Supero Supero SAS 846 TQ BACKPLANE Bedienungsanleitung

Supero

Supero AOC-SIMLC Bedienungsanleitung

Supero

Supero AOC-UG-i4 Bedienungsanleitung

Supero

Supero AOC-CIBQ-M1 Bedienungsanleitung

Supero

Supero Supero SAS-846EL Bedienungsanleitung

Supero

Supero Supero BPN-SAS-823TQ Bedienungsanleitung

Supero

Supero CSE-SATA-813L Bedienungsanleitung

Supero

Supero Supero SAS-846A Bedienungsanleitung

Supero

Supero BPN-EXP-847DR1EL1 Bedienungsanleitung

Supero

Supero Supero SAS2-847EL BACKPLANE Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

Intel

Intel NUC 12 Pro Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung

Advantech

Advantech ASMB-935 Series Bedienungsanleitung

Jupiter

Jupiter RAM PACK Bedienungsanleitung