Suprema FSF2ODB Bedienungsanleitung

FaceStation F2

USER GUIDE

EN 102.00.FSF2-ODB V1.02A

Version 1.02

English

Contents

Safety Instructions

Observe the following instructions to use the product safely and prevent any risk of injury or property damage.

Warning

Noncompliance with instructions can lead to serious injury or death.

Installation

Do not install the device under direct sunlight or UV light.

•Product damage, malfunction, discoloration, or deformation may occur.

Do not install the product in a location with direct sunlight, moisture, dust, or soot.

•Fire or electric shock may occur.

Do not install the product in a location with heat from an electric heater.

•Fire or electric shock may occur due to overheating.

Install the product in a dry location.

•Otherwise, product damage or electric shock may occur due to moisture.

Install the product in a location with no electromagnetic interference.

•Otherwise, product damage or electric shock may occur.

The user should not install or repair the product independently.

•Fire, electric shock, or personal injury may occur.

•If the product has been damaged due to independent installation or repair of the product by the user, free A/S service

will not be provided.

Operation

Do not allow liquids such as water, beverages, or chemicals get into the product.

•Fire, electric shock, or product damage may occur.

Caution

Noncompliance of instructions could lead to minor injury or product damage.

Installation

Do not install the power supply cable in a location where people pass by.

•Product damage or physical injury may occur.

Do not install the product near a highly magnetic object such as a magnet, TV, monitor (especially CRT), or speaker.

•Product failure may occur.

Use only a D.C 24 V and 2.5 A or higher power supply adaptor.

•If the proper power supply is not used, the product may not operate properly.

Use a separate power supply for the Secure I/O 2, electric lock, and FaceStation F2, respectively.

•If connecting and using the power supply to these devices together, the devices may malfunction.

Keep the minimum separation distances between the devices when install multiple devices.

•Otherwise, RF performance is affected to the other device, the devices may not operate normally.

Operation

Do not drop the product or apply an impact to the product.

•Product failure may occur.

Manage the password with care; do not to disclose it to others and change it periodically.

•Otherwise, illegal intrusion may occur.

Do not press the buttons on the product forcibly or using a sharp tool.

•Product failure may occur.

When cleaning the product, wipe the product with a soft and dry cloth. Do not apply water, benzene, or alcohol.

•These may cause product failure.

FaceStation F2 uses a capacitive screen and buttons. If the environment is moist from wet weather, or the product

surface is smeared with a large amount of water, wipe the product off with a dry towel before using it.

RTC battery

Replacing the battery with an incorrect type of battery may cause explosion.

Discard the battery according to appropriate regional or international waste regulations.

Introduction

Components

NOTE

•Components may vary according to the installation environment.

•When assembling the product with the bracket, you can use the included bracket fixing screw (Star Shaped) instead of the

product fixing screw for enhanced security.

•For additional content regarding product installation, visit the Suprema website (https://www.supremainc.com) and view

the installation guide.

FaceStation F2

Wall Bracket

Fixing Screw x6

PVC Anchor x6

Diode

Connection Cable

(1x2-pin, 1x3-pin, 3x4-pin)

Drilling Template

Quick Guide

120Ωresistor

Open Source Software

Guide

Bracket Fixing Screw

(Star Shaped)

Cable Cover

Name and function of each part

Name

Description

LED lamp

Turned on when the user is detected in the dark.

Infrared camera

Capture the infrared face image.

Visual camera

Capture an actual face image.

LCD screen

Provides UI for operation.

RF card and mobile access

card authentication unit

Part to scan the card for entrance.

Speaker

USB (Type-C) cable slot

Fingerprint sensor

Relay (3 pins)

Visual camera

SAM card slot

Power Supply (2 pins)

RS-485 (4 pins)

TTL Input (4 pins)

Wiegand Input/Output

(4 pins)

Ethernet

RF card and mobile access card

authentication unit

LCD screen

Infrared camera

LED lamp

Fingerprint sensor

Reads fingerprints.

Speaker

Delivers sound.

Ethernet

Connect the Ethernet cable.

TTL input (4 pins)

Connect the TTL input cable.

Relay (3 pins)

Connect the relay cable.

Wiegand input/output

(4 pins)

Connect the Wiegand input/output cable.

Power supply (2 pins)

Connect the power supply cable.

RS-485 (4 pins)

Connect the RS-485 cable.

SAM card slot

Insert the SAM card.

USB (Type-C) cable slot

Connect the USB cable.

Cables and connectors

Power supply

Name

Color

PWR +VDC

Red (white stripe)

PWR GND

Black (white stripe)

Relay

Name

Color

RLY NO

White

RLY COM

Blue

RLY NC

Orange

RS-485

Name

Color

485 TRXP

Blue

485 TRXN

Yellow

485 GND

Black

SH GND

Gray

TTL input

Name

Color

TTL IN0

Red

TTL IN1

Yellow

TTL GND

Black

SH GND

Gray

Wiegand input and output

Name

Color

WG D0

Green

WG D1

White

WG GND

Black

SH GND

Gray

Correct face registration and authentication method

Cautions for registering a face

•When registering a face, maintain a distance of 60 cm to 100 cm between the device and the face.

•Do not change your face expression.

•Do not wear masks, hats, or eye patches.

•Do not raise head up or lower head.

•Do not close your eyes.

•Do not wear thick makeup.

•Be careful not to display two faces on the screen. Register one person at a time.

•If you do not follow the instructions on the screen, the face registration may take longer or may fail.

Cautions for authenticating a face

•Ensure that the face appears in the center of the device's screen. When the guideline is displayed, follow the

instructions shown on the screen to authenticate the face.

•If a part of the face is covered with a hat, a mask, an eye patch, or sunglasses authentication may fail. Do not cover the

face; allow the device to recognize both the eyebrows and the face.

How to enroll a fingerprint

In order to improve the fingerprint authentication rate, register the fingerprint correctly. FaceStation F2 can recognize a

fingerprint even if the angle and position of a user's fingerprint input change. If you register the fingerprint with attention

to the following matters, the authentication rate can be improved.

Selecting a finger for fingerprint input

•In preparation for the case that the fingerprint of a specific finger cannot be used, for

example if the user is lifting a load with one hand or a finger gets hurt, up to 10

fingerprints for each user can be registered.

•In the case of a user whose fingerprint cannot be recognized well, the authentication

rate can be improved by enrolling the same finger twice repeatedly.

•If a finger has a cut or the fingerprint is blurry, select another finger for the

fingerprint.

•It is recommended to use the index finger or the middle finger when scanning the

fingerprint. The authentication rate can be reduced if it is difficult to place another

finger at the center of fingerprint sensor accurately.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere suprema Touch-Terminal Handbücher

suprema

suprema BioStation 2 Bedienungsanleitung

suprema

suprema XS2-DPB Bedienungsanleitung

suprema

suprema BioLite Net Bedienungsanleitung

suprema

suprema biostation Bedienungsanleitung

suprema

suprema BioStation L2 Bedienungsanleitung

suprema

suprema X-station Bedienungsanleitung

suprema

suprema biostation Bedienungsanleitung

suprema

suprema BioStation T2 Bedienungsanleitung

suprema

suprema FaceStation 2 Bedienungsanleitung

suprema

suprema FaceStation F2 Bedienungsanleitung

suprema

suprema X-Station 2 Bedienungsanleitung

suprema

suprema BioStation L2 Bedienungsanleitung

Beliebte Touch-Terminal Handbücher anderer Marken

Wincor Nixdorf

Wincor Nixdorf iPOS plus Advanced Bedienungsanleitung

Ingenico

Ingenico AXIUM EX4000 Bedienungsanleitung

Heisei Electronics

Heisei Electronics Q-POS 815 Bedienungsanleitung

Amano

Amano MTX-15 Bedienungsanleitung

FLOWBIRD

FLOWBIRD CWT Compact Touch Bedienungsanleitung

Demco

Demco SP7 Bedienungsanleitung

Lathem

Lathem PC600 Series Bedienungsanleitung

Partner

Partner MF-2352 Bedienungsanleitung

NCR

NCR RealPOS 7460-2 Handbuch

Simrad

Simrad MS50 Montageanleitung

Unitech

Unitech MR350 MKII Kurzanleitung

Jungheinrich

Jungheinrich WMT 210 Bedienungsanleitung

Motorola

Motorola MTP850 Bedienungsanleitung

YASKAWA

YASKAWA 62H-MDC0 Bedienungsanleitung

MVG industries

MVG industries NeptuLink Bedienungsanleitung

Price Industries Limited

Price Industries Limited FDC Gebrauchsanweisung

Honeywell

Honeywell TemaKey Bedienungsanleitung

EBN

EBN BPC65-B-A16G Bedienungsanleitung

suprema FSF2ODB Bedienungsanleitung

Beliebte Touch-Terminal Handbücher anderer Marken