SureCall Fusion2Go 2.0 Bedienungsanleitung
Fusion2Go 2.0™
Vehicle Voice and 4G Data Signal Booster
User Guide
Table of Contents
2
Thank you for purchasing SureCall’s Fusion2Go 2.0 cell phone signal booster kit. Fusion2Go 2.0
provides enhanced voice, text and 4G data signal for any vehicle.
If you have any questions during setup, please reach out to our US-based experienced support
technicians:
• Call: 1-888-365-6283
How It Works ................................................................................................................................. 3
Package Contents ......................................................................................................................... 4
Step 1: Mount Outside Antenna..................................................................................................... 5
Step 2. Install the Inside Patch Antenna........................................................................................ 5
Step 3. Install the Booster ............................................................................................................ 6
Step 4. Connect Power.................................................................................................................. 6
LED Indicators .............................................................................................................................. 7
Troubleshooting............................................................................................................................. 8
Specications ................................................................................................................................ 9
Antenna Kitting Information ......................................................................................................... 10
FCC and IC Information............................................................................................................... 12
How It Works
The SureCall Fusion2Go 2.0 is a high-quality bidirectional booster that enhances cellular signals for
vehicles.
The Fusion2Go 2.0 works with two antennas:
• An inside antenna that communicates with your cell phone.
• An outside antenna that communicates with the cell tower.
Signals sent from a cell tower are received by the outside antenna, amplied by the booster and
then sent to your cell phone via the inside antenna. When your phone transmits, the signal is sent to
the inside antenna, and then sent to the cell tower via the outside antenna.
How It Works
Outside Magnetic
Antenna
Power Adapter
Inside Antenna
Fusion2Go
4
Package Contents
Package Contents
1. Unpack all package contents. For missing or damaged items, contact your reseller.
2. Turn over the signal booster and record the model and serial number for reference:
Serial #:
Purchase Date:
3. Keep the carton and packing material to store the product in case you need to return it.
Your Fusion2Go 2.0 signal booster package includes the following items:
• One SureCall Fusion2Go 2.0 signal booster
• DC power adapter
• One inside patch antenna
• One outside magnetic mount antenna
Fusion2Go 2.0
Amplier
SC-120
Inside Patch Antenna
Warning: Unauthorized antennas, cables, and/or coupling devices are prohibited by FCC new rules. Please contact FCC for details:
1-888-CALL-FCC. Changes or modications not expressly approved by SureCall could void the user’s authority to operate the equipment.
Power Adapter Outside Magnetic-Mount
Antenna
Step 1: Mount Outside Antenna
Place the magnetic-mount antenna on the top of your vehicle preferably toward the back, maximiz-
ing the distance from planned location of the inside patch antenna. Ensure that the antenna has at
least a 12-inch radius clear of obstructions and other radiating elements, such as a radio antenna.
Next, run the cable from the outside antenna to the inside of the vehicle near the planned location
of the booster (under the seat of the vehicle, or in the front or middle console ). Run the outside
antenna cord across the car’s roof and under the front door insulation lining to hide and protect the
antenna cable.
Note: The outside antenna must not be collocated or operating with any other antenna or booster.
Step 2. Install the Inside Patch Antenna
Find a location for the inside patch antenna that is within 2-3 feet of the typical cell phone location.
Choose a location that is at least 4 inches (10cm) away from metal and afx the antenna to the
chosen surface. Then run the connected cable to the planned location of the booster.
Installation
6
Installation
Step 3. Install the Booster
Place the booster under the seat of the vehicle or any convenient location within the vehicle. Choose
a location that is away from excessive heat, direct sunlight or moisture and with proper ventilation.
Connect the cable from the outside antenna to the connection marked OUTSIDE and connect the
cable from inside patch antenna to the connection marked INSIDE. Tighten the connections and
wrap up any loose cable.
Step 4. Connect Power
Connect the power cord connector to the signal booster and insert the other end into your cigarette
lighter adapter. The Power LED lights up to show that the signal booster is ready for use. The Alert
LEDs ash 5 times to show the frequency band is operational.
Place a call in a location you have previously experienced poor signal and conrm that your phone
is receiving a boosted signal.
Note: .1. The patch antenna must remain at least 20 cm away from the body
2. The Patch antenna must be at least 20 cm away from the phone or cradle that phone is sitting in.
3. Laboratory tests show that patch antennas can work from as close as 2 ft. from the outside antenna if the patch
antenna is facing away from the outside antenna.
LED Indicators
In the event Red LEDs appear either solid or ashing, further separation between the booster and
outside antenna is recommended.
Note that the booster case may become warm during operation. This is normal.
WARNING. The booster is rated for 5-15V input voltage. DO NOT use the booster with a higher voltage power supply. This can damage the
booster and/or cause personal injury.
Installation
DC Power Connection
Connector to Inside Antenna
Connector to Inside antenna
Connector to Outside
Magnetic antenna
8
SpecicationsTroubleshooting
Troubleshooting
Problem Resolution
Signal booster has no
power
Verify that the LED on the booster is ON.
Connect the power supply to an alternate power source.
Verify that the power source is operational and the fuse is intact.
If the POWER LED on the signal booster is OFF, return the power supply to SureCall. Contact tech support at to
receive an RMA at:
After completing
installation, signal has
not Improved
Verify that cable connections are tightly tted to the booster.
Try further separating the antennas.
Remember: Bars are not always a reliable measure of signal. The best way to conrm signal coverage is the
ability to place and hold a call.
Specications
RF Exposure Warning:
The inside patch antenna must be installed so as to provide a separation distance of al least 20 cm (8 inches) from all persons
The Manufacturer’s rated output power of this equipment is for single carrier operation. For situations when multiple carrier signals are present,
the rating would have to be reduced by 3.5 dB, especially where the output signal is re-radiated and can cause interference to adjacent band
users. This power reduction is to be by means of input power or gain reduction and not by an attenuator at the output of the device.
Specications
Product Fusion2Go 2.0 US Fusion2Go 2.0 Canada
Uplink Frequency Range (MHz): 698-716 / 776-787 / 824-849 / 1850-1915 / 1710-1755 (G Block Included)
Downlink Frequency Range (MHz): 728-746 / 746-757 / 869-894 / 1930-1995 / 2110-2155 (G Block Included)
Input / Output Impedance: 50 Ω
Maximum Gain: 50 dB 47.8 dB
Noise Figure: ≤ 5 dB
VWSR: ≤ 2.0
Gain Adjustment: 20 dB (Automatic)
Supported Standards: CDMA, WCDMA, GSM, EDGE, HSPA+, EVDO, LTE and all cellular standards
DC Power: 6-15V
Maximum Output Power: 1 Watt EIRP 3 Watt EIRP
Cable: SC-174
RF Connectors: FME Male (both ends)
Power Consumption: ≤ 10W
Operation Temperature: -4º to +158º F
Dimensions: 5.625 x 4 x 1.125 inches
Weight: 1.43 lbs
FCC / IC ID: RSN2GOMINI 7784A-2GOMINI
10
Antenna Kitting Information
Component Prod No. Description Gain Notes
LTE-A LTE-V 800 MHz 1900 MHz 1700 MHz \
2100 MHz
Vehicle Kit 1
Outdoor Antenna
and Cable
SC200W
SC174-10 ft (10 ft)
-2.3 dB -2.3 dB -2.3 dB -5.8 dB -3.98 dB \ -
5.96 dB
Indoor Antenna and
Cable
SC110W
SC174-10 ft (10 ft)
-2.7 dB -2.7 dB -3.2 dB -5.8 dB -3.98 dB \ -
5.96 dB
Tabletop Antenna
Vehicle Kit 2
Outdoor Antenna
and Cable
SC208W
SC174-12.5 ft (12.5 ft)
-3.16 dB -5.15 dB -5.65 dB -2.85 dB -3.34 dB \
NG
Indoor Antenna and
Cable
SC110W
SC174-10 ft (10 ft)
-2.7 dB
-2.7 dB
-3.2 dB -5.8 dB -3.98 dB \
-5.96 dB
Tabletop Antenna
*All equivalent antennas and cables are suitable for use with the Fusion2Go 2.0
Component Prod No. Description Gain Notes
LTE-A LTE-V 800 MHz 1900 MHz 1700 MHz \
2100 MHz
Marine 1 Kit
Outdoor Antenna
and Cable
SC288W or Galaxy 5412-P
SC240-40FN (40 ft)
-0.52 dB -0.52 dB -0.98 dB -2.52 dB -2.12 dB\-
2.92 dB
Indoor Antenna and
Cable
SC248W
SC240-20FN (20 ft)
4.94 dB 4.94 dB 4.71 dB 6.44 dB 6.64 dB \
6.24 dB
Wall Mounted
Antenna
Marine 2 Kit
Outdoor Antenna
and Cable
SC288W or Galaxy 5412-P
SC240-40FN (40 ft)
-0.52 dB -0.52 dB -0.98 dB -2.52 dB -2.12 dB \
-2.92 dB
Indoor Antenna and
Cable
SC302W
SC240-20FN (20 ft)
0.44 dB 0.44 dB 0.71 dB 1.44 dB 0.64 dB \
1.24 dB
*All equivalent antennas and cables are suitable for use with the Fusion2Go 2.0
Component Prod No. Description Gain Notes
LTE-A LTE-V 800 MHz 1900 MHz 1700 MHz \
2100 MHz
Desktop / RV 1 Kit
Outdoor Antenna
and Cable
SC288W
SC240-40FN (40 ft)
-0.52 dB -0.52 dB -0.98 dB -2.52 dB -2.12 dB \
-2.92 dB
Indoor Antenna SC120W 1.2 dB 1.2 dB 1.2 dB 3 dB 3 dB \ 3 dB Tabletop Antenna
Desktop / RV 2 Kit
Outdoor Antenna
and Cable
SC288W
SC240-40FN (40 ft)
-0.52 dB -0.52 dB -0.98 dB -2.52 dB -2.12 dB \
-2.92 dB
Indoor Antenna and
Cable
SC302W
SC240-20FN (20 ft)
0.44 dB 0.44 dB 0.71 dB 1.44 dB 0.64 dB \
1.24 dB
*All equivalent antennas and cables are suitable for use with the Fusion2Go 2.0
Kitting InformationKitting Information
Andere Handbücher für Fusion2Go 2.0
1
Inhaltsverzeichnis
Andere SureCall Extender Handbücher
SureCall
SureCall N-Range Bedienungsanleitung
SureCall
SureCall Fusion5S CA Bedienungsanleitung
SureCall
SureCall EZ 4G Bedienungsanleitung
SureCall
SureCall 5X Max Bedienungsanleitung
SureCall
SureCall Force5 Inline Bedienungsanleitung
SureCall
SureCall FusionTrek Bedienungsanleitung
SureCall
SureCall Fusion2Go 3.0 CA Bedienungsanleitung
SureCall
SureCall EZ Connect Bedienungsanleitung
SureCall
SureCall SC-PolyO2-72 Bedienungsanleitung
SureCall
SureCall Fusion Professional 2.0 Bedienungsanleitung
SureCall
SureCall Flare 3.0 Bedienungsanleitung
SureCall
SureCall Fusion4Home Omni/Panel Bedienungsanleitung
SureCall
SureCall Fusion4Home Yagi/Whip Bedienungsanleitung
SureCall
SureCall BOOSTRV Bedienungsanleitung
SureCall
SureCall Fusion2Go 3.0 CA Bedienungsanleitung
SureCall
SureCall Flex2Go Canada Bedienungsanleitung
SureCall
SureCall TriFlex SC-TriH/O-72-OD-Kit Bedienungsanleitung
SureCall
SureCall EZ 4G Bedienungsanleitung
SureCall
SureCall Flare 3.0 Bedienungsanleitung
SureCall
SureCall M2M-V Bedienungsanleitung
