PISTON ASSEMBLY
Place piston into suppressor back section and place spring or
fixed barrel spacer (with spring facing rear) over piston shaft.
Place rear cap over exposed piston shaft, push until flush with
suppressor tube, and tighten until hand tight by turning clockwise.
Note: Rear cap should only be tighten by hand. Tool is only to be
used for disassembly.
DISASSEMBLY
1. Insert the Disassembly/Assembly Tool Central Rod into the bore
of the suppressor front plate. Align the Disassembly/Disassembly
Tool Pins with the blank holes in the suppressor front plate and
push the tool snug against the front plate. (Fig. 1)
2.Rotate the Disassembly/Assembly Tool counterclockwise while
holding or rotating the suppressor clockwise, until the front plate
is unscrewed. (Fig. 2)
3.Push the front plate and baffle stack through the front of the
suppressor tube with the Baffle Removal Tool. The Baffle
Removal Tool is designed to interface with the shear cut of the
baffle. (Fig. 3)
Note: After the suppressor has been shot the baffle stack may become
difficult to push through. If this is the case, place the Baffle Removal
Tool on the Disassembly/Assemble Tool Central Rod and rotate until
it mates with the shear cut on the baffle. Use the tool for leverage to
push the baffle stack through. Remove the Baffle Removal Tool once
the baffle stack has been pushed through the suppressor tube.
CLEANING
The SF RYDER 9-Ti2 should be cleaned periodically to ensure
optimal performance. Recommended cleaning of the suppressor
piston is at least every 300 rounds – and the baffles every 1,000
rounds. Clean the baffles with non-flammable cleaning solvent.
Wipe the baffles dry with a clean, dry cloth or cleaning patches.
Clean sooner if there is noticeable carbon buildup or any sacrifice
in sound attenuation.
ASSEMBLY
1. Slide the front plate onto the Disassembly/Assembly Tool
central rod and align the tool pins with the blank holes in the
front plate.
2. Slide Baffle #1 onto the Disassembly/Assembly Tool Central
rod. Slide Baffle #2 onto the central rod and align index tab
so Baffle #2 can be pushed flush with Baffle #1. Repeat this
process with Baffle #3 through #6,in that order, ensuring that
all of the baffles are flush and the numbering is in alignment.
Next place the spacer on the baffle stack.
3. Slide the suppressor tube over the entire stack.
4. Rotate the Disassembly/Assembly Tool counterclockwise,
while holding the suppressor tube or rotate suppressor tube
clockwise until hand tight. Slide the Disassembly/Assembly
Tool out from the suppressor.
SF®RYDER 9-Ti2
INTRODUCTION
The SureFire RYDER 9-Ti2 is a lightweight suppressor optimized for
9mmpistols andrifleswith1/2x28 orM13.5x1LHthreadedmuzzles.
The suppressor features a durable yet lightweight titanium body
with rounded ends and flutes to reduce weight with no sacrifice in
strength. It is finished in a durable Cerakote coating and internally
has patented stainless baffles that provide superior sound
attenuation and reduce muzzle blast. Additionally the SF-SPCR-
9Ti2 Fixed Barrel Spacer (sold separately) is recommended when
shooting a fixed-barrel firearm, or a 9 mm carbine weapon system.
KIT CONTENTS
The SF RYDER 9-Ti2 ships standard with the following items:
• SF RYDER 9-Ti2 Suppressor (assembled)
• Disassembly/Assembly Tool
• Baffle Removal Tool
• Suppressor Holster
• User Manual
ATTACHMENT/REMOVAL
To attach the SF RYDER 9-Ti2, align the muzzle threads with
the suppressor threaded piston and screw the suppressor on
clockwise (or counterclockwise with the M13.5x1 LH) until
hand tight.
To remove the SF RYDER 9-Ti2, unscrew the suppressor
counterclockwise (or clockwise for the M13.5x1 LH) and remove
the barrel.
PISTON REMOVAL
Unscrew rear cap with the back end of the Disassembly/
Assembly Tool by turning counterclockwise and remove.
Pull piston spring and piston clear of the suppressor tube.
FIGURE 1
FIGURE 2
FIGURE 3
REAR
CAP
NUMBERED BAFFLES
SPACER
PISTON
SPRING
PISTON
SCREW ON
(CLOCKWISE)
UNSCREW OFF
(COUNTERCLOCKWISE)
BAFFLE CHAMBERPISTON CHAMBER
ALWAYS confirm weapon is unloaded and on SAFE
before attaching or removing
DISASSEMBLY/ASSEMBLY
TOOL
BAFFLE REMOVAL
TOOL
CAUTION: Suppressor may be extremely hot after firing
the weapon. Allow the suppressor to cool or wear appropriate
gloves before removing.
(1/2 x 28 shown)
