5
ENGLISH•User's Manual
MANTEINANCE
ELECTRIC HOIST WARNING! Before using this
electric tool, read the general safety rules listed
below carefully. Failure to do so could resultin
injury or equipment damage.
Congratulations on your excellent choice. Your
new electric tool is manufactured in compliance
with the best reliability and quality standards
, ensuring you efficiency and safety for a long
period of time.
GENERAL SAFETY RULES
Electrical safety Wall socket must meet standard
safety regulations, In Case of any doubt all wall
sockets should be checked by a qualified electri-
cian to ensure they are suitable. The plug must
be securely grounded and your electrical system
must be supplied with a magnetic cut-out safety
switch. Do not pull on the electric cable to dis-
connect the plug. The machine should only be
operated by specially trained persons with a tho-
rough knowledge of the safety rules and regu-
lations. When the machine is idling, make sure
it is out of the reach of children. The machine
should be protected from frost and low tempe-
ratures. If the machine is unable to hoist a load,
do not continue pressing the hoisting button:
this means that the load exceeds the machine's
maximum capacity. Do not overload! Do not use
2 or more electric hoists to lift one item. Do not
lift heavy items aslant; do not use the electric
hoist to drag items along the ground. Do not
lift stationary items. Do not attempt to dismant-
le the machine while it is running or while it is
connected to the power supply The machine
should not be operated during rain or storm.
Forindoor use only! DO NOT USE OUTDOORS.
Never hoist persons. Do not stand under hoisted
loads. Before beginning to operate this machi-
ne ensure that the steel cable is correctly wound
on the spool and the pitch is equal to the cable
diameter. Leave at least 3 complete windings of
cable on the hoist, to avoid damage to the cable
fixation.. - Avoid winding over 15m of cable on
the hoist Press button before loading to elimi-
nate any slack in the steel rope, only then lift
the load.
In case of using an electrical extension external
to the hoist, it will have to be a 12 AWG gauge.
The hoist will have to be used with a stable vol-
tage of 110 V.
The use or working time of the hoist must meet
the standard S3-25%: Work for 3 minutes and
stop to rest for 7 minutes.
NO NO SI
Please respect the maximum load indicated on
the label. Always disregard the capacity indica-
ted on the hook. Do not leave heavy items sus-
pended for too long in order to avoid perma-
nent strain on parts and to prevent accidents.
When the steel cable has become worn , replace
it only with a cable of the same specifications
manufactured by us. Our cables can be found at
all authorized service outlets. Before operating
the machine, check that switches are in good
operating condition. Attention: The motor has
no cut-off function. Do not use it for overloads.
If the machine is unable to lift an item, do not
attempt to force it. Switch the motor off to
allow it to cool, reduce the load, and lift again.
- Position-Limit Safety Device: The position-limit
safety device is designed to prevent capacity li-
mits being exceeded when lifting or lowering a
load. Do not use it as a travel switch and never
try to dismantle. The hoist brake system The
hoist brake system is factory-adjusted to work
within the rated load conditions sometimes af-
ter long use the rubber in the brake system will
become worn and the brake will no longer work
as it should. If you feel that your hoist can no
longer lift and hold the load for which it is inten-
ded, please contact your dealer to replace the
friction plate. The electric hoist features up and
down limit-position safety devices. When a load
is hoisted to the limit-position level, the machi-
ne will stop lifting. Conversely if the downward
movement is too fast the safety switch will be
triggered and the machine will stop working.
The down safety switch is installed on the side
of machine under the end cover. There must be
a minimum of 2 turns of wire rope on the spool
when the down safety switch triggers, otherwi-
se it is out of adjustment and you should have
it reset at your local dealer. Please ensure that
you check all easily-wearing parts as mentioned
above every 6 months to ensure the safety of
the operator and the machine.
2 INSTALLATIONS The hoist "standard version"
is fitted with a specially-designed bracket sys-
tem that enables it to be bolted to a round,
square or rectangular shaped support.
