SWELLPRO GC2-S Bedienungsanleitung

GC2-S

User Guide

Visit www.swellpro.com to download the latest version of the manual and firmware.

V1.0 –2021.3

Thank you

The GC2-S is a waterproof low-light 2-axis gimbal camera designed for SplashDrone 4 to gain visual footage in

a low-light environment. The GC2-S comes with a dimmable LED light that allows use even in complete

darkness. The high-sensitivity sensor of the GC2-S provides full-color images in a low-light environment when

normal cameras cannot return an image.

Using this manual

This document is designed to be printed or viewed on a computer or mobile device.

Tutorial videos

To watch tutorial videos or download the firmware, please visit SwellPro website www.swellpro.com

Contents

Thank you 2

Using this manual 2

Tutorial videos 2

CONTENTS 3

PRECAUTION 4

INSTALLATION 4

Install the Gimbal 4

Install SD Card 5

After Use Casing 5

CONTROL 5

Gimbal Control 5

Camera control 6

APP INTERFACE 6

SPECIFICATION 9

Precaution

●The GC2-S is a piece of precision electronics with corrosion-resistant materials which allow for use in

harsh marine environments. As with any marine equipment, trouble-free and lasting operations depend

on proper attention and maintenance of the equipment.

●When taking off or landing, slowly proceed to avoid damage to the gimbal camera which can cause by

the huge impact when contacting the surface at high speeds. Drop or crash directly into the water from

above will result in significant damage to the drone and the gimbal camera.

●After using in seawater, soak and rinse thoroughly with clean fresh water before the seawater dries out.

●If seawater or other sediments form on the gimbal camera, soak thoroughly with fresh water and clean

all sediments on the camera and motor before use. For more information, check the drone’s

“Maintenance manual”.

Installation

Install the Gimbal

1. Unscrew and take off the gimbal port cover plate using a hex

screwdriver. (equipped with SplashDrone 4)

2. Plug the gimbal connector into the drone’s gimbal port and screw

it in place with a screwdriver.

⚠Make sure the rubber ring is attached to the gimbal connector

before you screw the connector.

3. Aline the holes on the base of the gimbal to the bottom of the

drone, screw in to mount the gimbal. Make sure the camera is

pointing to the front of the drone.

Install SD Card

1. Open the soft rubber seal on the top of the camera, insert the Mirco

SD card in the correct direction, press the Mirco SD card, the "click"

sound indicates that the installation is in place.

2. After installing the Mirco SD card, plug the rubber seal back.

⚠Make sure the rubber seal is tightly plugged in to ensure

waterproofing.

●The GC1-S supports Mirco SD cards with a maximum capacity of 128GB. Since the camera requires fast

reading and writing of high-stream video data, please use Mirco SD cards with Class 10 or UHS-1 or

above to ensure proper functioning.

●Do not insert or unplug the Mirco SD card during aircraft shooting, as data files may be damaged or

lost.

●Once you are done recording, stop recording and save the file. If you turn off the power directly

before saving the files, the recording file will be lost.

After Use Casing

After using the gimbal camera, you can choose not to take off the gimbal camera and put it directly into

the case with the drone. Follow the following steps to make sure the gimbal camera is properly secure

after casing.

1. Remove the double-side-glued pad from the gimbal box and paste

the pad into the drone’s case as showing to the left.

2. After cleaning and drying the gimbal camera and the aircraft, secure

the gimbal camera with the fixing case, then put the aircraft and other

parts into the case. The case is secure and ready to be carried or

transported.

Control

Gimbal Control

Remote controller[1]

Description

[2]

Tilt: Toggle the right gimbal control as shown to turn the gimbal up or

down from 0 to -90 degrees.

Dimmable LED light control: Toggle the left gimbal control to adjust

the dimmable LED light. (Dimmable LED light works the best when the

aircraft is 15 meters away from the subject.)

Camera control

Remote controller

Description

Video: press once to start recording, press again to stop recording,

and save files.

Photo: press once to take a picture.

APP Interface

To get into APP’s camera interface: Power on the remote controller, then the aircraft. Connect the phone to

the remote controller’s Wi-Fi hotspot. Then click "Login device".

Camera Interface

Photo Setting Interface

Video Setting Interface

Camera Setting Interface

Playback Interface

Specification

Gimbal

Waterproof rating:

IP67

Stabilization:

2-axis (tilt, roll).

Controllable range:

Tilt: -90° to 0°

Max control speed:

Tilt: 60 °/s

Weight:

About 145 g

Size:

71*55*65mm

Camera

Sensors:

1/2" 2M CMOS

Lens:

FOV: 92.6°

Photo size:

4:3/16:9 12MP

Burst mode:

3/5/10 shoots

Interval shot:

1/3/5/10 s

Video resolution:

FHD：1920*1080 30/60p | HD：1280*720 120/60p

Max data stream:

64 MBps

Photo format:

JPEG

Video format:

MP4，MOV

Memory card:

Micro SD card: supports up to 128GB of capacity, write speeds ≥ 60

MB/s, and transfer speed rating of Class 10 or above, or with UHS-1

rating.

Working temperature:

-10°C - 40°C

Andere Handbücher für GC2-S

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere SWELLPRO Drohne Handbücher

SWELLPRO

SWELLPRO SPLASH DRONE Bedienungsanleitung

SWELLPRO

SWELLPRO JCMATTHEW D1 Bedienungsanleitung

SWELLPRO

SWELLPRO FPV Goggle Bedienungsanleitung

SWELLPRO

SWELLPRO SWIFT 2 Bedienungsanleitung

SWELLPRO

SWELLPRO Splash Drone 3 Bedienungsanleitung

SWELLPRO

SWELLPRO SplashDrone 4 Bedienungsanleitung

SWELLPRO

SWELLPRO spry Bedienungsanleitung

SWELLPRO

SWELLPRO JCMatthew FD1 Bedienungsanleitung

SWELLPRO

SWELLPRO Splash Drone 3 Bedienungsanleitung

SWELLPRO

SWELLPRO Splash Drone PR Bedienungsanleitung

SWELLPRO

SWELLPRO Splash Drone 3 Bedienungsanleitung

SWELLPRO

SWELLPRO Splash Drone Pro Bedienungsanleitung

SWELLPRO

SWELLPRO Splash Drone 3 Bedienungsanleitung

SWELLPRO

SWELLPRO Splash Drone 4 Bedienungsanleitung

SWELLPRO

SWELLPRO spry Bedienungsanleitung

SWELLPRO

SWELLPRO SplashDrone 4 Montageanleitung

SWELLPRO

SWELLPRO SPLASH DRONE Bedienungsanleitung

SWELLPRO

SWELLPRO Splash Drone 3 Bedienungsanleitung

SWELLPRO

SWELLPRO Splash Drone Pro Bedienungsanleitung

SWELLPRO

SWELLPRO Splashdrone Fisherman FD1 Bedienungsanleitung

SWELLPRO

SWELLPRO SPLASH DROME 3 Bedienungsanleitung

SWELLPRO

SWELLPRO SPLASH DRONE Bedienungsanleitung

SWELLPRO

SWELLPRO Fisherman Bedienungsanleitung

SWELLPRO

SWELLPRO SPLASHDRONE 3 Betriebsanleitung

Beliebte Drohne Handbücher anderer Marken

Ryze

Ryze Tello Bedienungsanleitung

PowerVision

PowerVision PowerRay Bedienungsanleitung

Force1

Force1 rogue F72 Bedienungsanleitung

Zerotech

Zerotech DOBBY Bedienungsanleitung

Protocol

Protocol VIDEODRONE AP Bedienungsanleitung

dji

dji Matrice M210 Bedienungsanleitung

MAKE

MAKE Terry Kilby Bedienungsanleitung

SYMA

SYMA X440 Bedienungsanleitung

RUKO

RUKO F11 Bedienungsanleitung

SYMA

SYMA X5UW(720P) Bedienungsanleitung

Dynali

Dynali 25 H Leitfaden

dji

dji PHANTOM 4 Bedienungsanleitung

Atlas

Atlas AtlasPRO Bedienungsanleitung

Twodots

Twodots TVVIN BOARD Bedienungsanleitung

GDU

GDU SAGA Bedienungsanleitung

Ares

Ares ETHOS QX 130 Bedienungsanleitung

Walkera

Walkera ZHUN Bedienungsanleitung

dji

dji WIND-4 Bedienungsanleitung