Swisher L122-265001 Bedienungsanleitung

9/22/2022

Read and follow all Safety

Precautions and Instructions

before operating this

equipment.

LOG

SPLITTER

OWNER’S

MANUAL

SWISHER ACQUISITION INC.

1602 CORPORATE DRIVE, WARRENSBURG MISSOURI 64093

PHONE 660-747-8183 TOLL FREE 800-222-8183 FAX 660-747-8650

MODEL NO.

LSED14534

STARTING SERIAL #:

L122-265001

Manufacturing quality lawn care equipment since 1945

Safety

Assembly

Operation

Service and Adjustment

Repair Parts

IMPORTANT

swisherinc.com

20404

REV 22-265

Made In The

USA

of US and Global Parts

LIMITED WARRANTY

The manufacturer’s warranty to the original consumer purchaser is: This product is free from defects in

materials and workmanship for the period's shown below beginning from the date of purchase by the original

consumer purchaser.

As required by CFR § 1060.120, the fuel system related components, which have been certified to this

equipment by SAI are to be free of defects in material and workmanship for a period of two (2) years from the

date of purchase by the original consumer purchaser.

We will repair or replace, at our discretion, parts found to be defective due to materials or workmanship. This

warranty is subject to the following limitations and exclusions:

Engine Warranty All engines utilized on our products have a separate warranty extended

to them by the individual engine manufacturer. Any engine service

difficulty is the responsibility of the engine manufacturer and in no

way is Swisher, or its agents responsible for the engine warranty. Engine

warranty and contact information is as shown in the engine owners manual.

Hydraulic System 1 Year

Materials and Workmanship 3 Years

Limitation This warranty applies only to products which have been properly

assembled, adjusted, and operated in accordance with the instructions

contained within this manual. This warranty does not apply to any

product of Swisher that has been subject to alteration, misuse, abuse,

improper assembly or installation, shipping damage or to normal wear of

product.

Exclusions Excluded from this warranty are normal wear items, normal or routine

adjustments, and normal or routine maintenance.

In the event you have a claim under this warranty, you must return the product to an authorized service dealer.

All transportation charges, damage, or loss incurred during transportation of parts submitted for replacement or

repair under this warranty shall be borne by the purchaser. Should you have any questions concerning this

warranty, please contact us toll-free at 1-800-222-8183. The model number, serial number, date of purchase,

and the name of the authorized Swisher dealer from whom you purchased the splitter will be needed before any

warranty claim can be processed.

THIS WARRANTY DOES NOT APPLY TO ANY INCIDENTAL OR CONSEQUENTIAL

DAMAGES AND ANY IMPLIED WARRANTIES ARE LIMITED TO THE SAME TIME PERIODS

STATED HEREIN FOR ALL EXPRESSED WARRANTIES. Some states do not allow the limitation of

consequential damages or limitations on how long an implied warranty may last, so the above limitations or

exclusions may not apply to you. This warranty gives you specific legal rights and you may have other rights,

which vary from state-to-state. This is a limited warranty as defined by the Magnuson-Moss Act of 1975.

SAFETY PRECAUTIONS

WARNING: The engine exhaust from this product contains chemicals known to the state of California to

cause cancer, birth defects or other reproductive harm.

DANGER: Your log splitter was built to be operated according to the rules for safe operation in this manual.

As with any type of power equipment, carelessness or error on the part of the operator can result in serious

injury. If you violate any of these rules, you may cause serious injury to yourself or others.

Read and understand the manual. Learn to operate this equipment in a safe manner. Familiarize

yourself with all of the controls in a safe environment before starting to work with this machine.

DO NOT under any circumstances alter this log splitter. This equipment was designed and

engineered in accordance with operating instructions. Altering this equipment, or using this

equipment in such a way as to circumvent its design capabilities and capacities, could result in

serious injury or fatality and WILL VOID THE WARRANTY.

Allow ONLY responsible adults who have read this manual to operate this machine. NEVER allow

children to operate this machine.

NEVER operate or allow someone to operate this equipment while under the influence of alcohol,

drugs or medication. Being coherent is essential for safety.

ALWAYS use outdoors with adequate ventilation. DON’T run the engine in an enclosed area.

Exhaust gases contain carbon monoxide. This odorless gas can be deadly when inhaled.

NEVER use splitter for any other purpose than splitting wood. Any other use can result in injury.

Your splitter is a precision piece of power equipment, not a toy. Therefore, exercise extreme caution

at all times.

ONLY a single operator is to load and operate the log splitter. KEEP all others, including pets and

children, a minimum of 20 feet away from your work area. More accidents occur when more than

one person operates the log splitter than any other time.

ALWAYS wear protective gear such as safety goggles, protective hearing device, steel-toed shoes,

and tight-fitting gloves without drawstrings or loose cuffs.

NEVER wear loose clothing or jewelry that can be caught by moving parts of the splitter and pull

you into it. Keep hair away from moving parts.

NEVER operate your splitter on wet, muddy, or icy surfaces. KEEP work area clean of split wood.

Safe footing is essential in preventing accidents.

ONLY operate splitter on level ground with wheels blocked, not on the side of a hill. It could tip, or

rolling logs, poor footing, etc. could cause an accident.

This Safety Alert Symbol indicates important messages in this manual.

When you see this symbol, carefully read the message that follows and be

alert to the possibility of personal injury.

Read this manual completely. This machine can amputate hands, feet, and throw objects.

Failure to observe the following safety instructions could result in serious injury or death.

NEVER operate your splitter near a flame or spark. Hydraulic oil and gasoline are flammable and can

explode.

NEVER fill gas tank while the engine is hot or running. Allow the engine to cool before refueling.

This unit is equipped with an internal combustion engine and should not be used on or near any

unimproved forest-covered, brush-covered or grass-covered land unless the engine’s exhaust system is

equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used it

should be maintained in effective working order by the operator.

-NOTE-

In the state of California, the above is required by law (Section 442 of the California Public Resources Code).

Other states may have similar laws. Federal laws apply on federal lands. A spark arrester muffler (optional by

manufacturer) is available at your nearest engine dealer. Check legal requirements in your area.

ONLY use your hands to operate the control lever. NEVER use foot, knee, rope or any extension device.

Split ONLY one log at a time. NEVER attempt to split two logs on top of each other.

NEVER place hands or feet between log and splitting wedge or between log and buttplate during forward

or reverse stroke. ALWAYS keep fingers clear of splits that open in log during splitting operation.

DO NOT straddle or reach across the splitting area while operating the splitter.

DO NOT step over splitter when the engine is running. You may trip or accidentally activate the splitting

wedge. Walk around to get to the other side.

NEVER attempt to load splitter while splitting wedge is in motion. When loading log splitter, place hands

on the sides of the log, not the ends.

NEVER attempt to split woods across the grain. Wood may burst or fly out of your splitter and result in

serious injury.

NEVER leave your splitter unattended with the engine running. Shut off the engine if you are leaving

your splitter, even for a short period of time. Someone could accidentally activate the ram and be injured.

Both ends of the log should be cut as squarely as possible to prevent the log from sliding out of the splitter

during operation. Log length should be kept to 24” or less.

NEVER operate your splitter while it is attached to the tow vehicle.

BEFORE towing, be certain that the splitter is securely attached to the towing vehicle and that the support

leg, beam, 4-way wedge and cylinder are secured in there respective towing positions.

DO NOT loosen or remove any hydraulic fitting, line or reservoir cap while your splitter or engine is

running.

Fluid escaping from a very small hole can almost be invisible. DO NOT check for leaks with your hand.

See maintenance section for instructions. IF injured by escaping fluid, see a doctor at once. Serious

infection or reaction can develop if proper medical treatment is not administered immediately.

DO NOT operate your splitter in poor mechanical condition or when it is need of repair.

ALWAYS disconnect the spark plug wire and place the wire where it cannot contact the spark plug, to

prevent accidental starting the engine when setting up, transporting, adjusting or repairing.

TOWING SAFETY

Do not allow persons to ride on splitter. Do not carry any cargo or wood on your

splitter. It may fall off and endanger vehicles that are following you.

Be sure support leg is in the travel position and coupling secure. This must also be

retracted so as not to interfere while towing. Retract support leg by removing pin,

pivoting up, and replacing pin.

Never exceed 45 MPH while towing your splitter. Be extra cautious when traveling

over rough terrain, especially over railroad tracks.

Always be careful while backing your splitter. You could jackknife your log splitter

if not careful.

Before using splitter, disconnect it from tow vehicle. A log could easily be pushed

forward into the vehicle.

See proper inflation instructions on side of tires.

Be aware of the extra length of splitter while turning, parking, crossing intersections,

and in all driving situations.

OPERATION INSTRUCTIONS

POSI-LOCK COUPLER

ADJUST COUPLER LOCKING PRESSURE ON BALL BEFORE USE. PLACE HANDLE IN LOCKED

POSITION WITH BALL IN COUPLER. TIGHTEN LOCKNUT AGAINST TENSION SPRING SO THAT

COUPLER IS NOT LOOSE ON BALL. CORRECT ADJUSTMENT WILL ALLOW HANDLE TO BE

RELEASED WITH MODERATE PRESSURE APPLIED TO HANDLE.

TO OPEN, PULL UP ON COUPLER HANDLE AND ROTATE FORWARD. PLACE COUPLER ON BALL

WHEN BALL IS COMPLETELY NESTED IN BALL SOCKET, ROTATE COUPLER HANDLE

BACKWARD UNTIL HANDLE IS IN LOCKED POSITION.

AFTER TOWING FOR 50 MILES, CHECK COUPLER FOR TIGHTNESS ON BALL. ALWAYS CHECK

TIGHTNESS BEFORE TOWING. BE SURE COUPLER HANDLE IS IN LOCKED POSITION.

WARNING:

NEVER EXCEED WEIGHT CAPACITY AND ALWAYS USE SAFETY CHAINS. ALWAYS USE

CORRECT BALL SIZE, MAKING SURE BALL IS COMPLETELY INSERTED INTO COUPLER. LOCK

COUPLER HANDLE SECURELY BEFORE TOWING. ALWAYS CHECK FOR DAMAGES AND

REPLACE IF DAMAGED. AVOID SHARP TURNS AND STEEP VERTICAL ANGLES WHEN TOWING.

ASSEMBLY

Refer to the drawings and part lists should it become necessary to disassemble the unit for repair or replacement of

parts.

Inspect all components for damage. If you believe you have a damaged part please contact customer service

immediately at 1-800-222-8183.

WARNING: Exercise extreme caution, as parts are very heavy. Sufficient persons or mechanical handling

equipment should be used.

Refer to uncrating and assembly instructions for assembly procedures.

OPERATION

INTENDED USE: This log splitter is intended and designed to only split wood. NEVER use for any other

purposes. Doing so can cause injury or VOID THE WARRANTY.

IMPORTANT: This unit is shipped with oil but without gasoline in the engine. After assembly, see separate

Engine Manual for proper fuel and oil recommendations.

WARNING: DO NOT START OR RUN THE LOG SPLITTER WITHOUT OIL IN THE ENGINE AND

HYDRAULIC RESERVOIR.

FILLING THE HYDRAULIC RESERVOIR

Fill the hydraulic reservoir to the top mark on the dipstick or, depending on your Log Splitter model, to the lower fill

line of the reservoir with Dexron III / Mercon automatic transmission fluid, 10W AW hydraulic fluid or Pro-Mix

AW-32 Hydraulic oil. After the hydraulic reservoir and the engine crankcase are filled correctly with their respective

oils, set the throttle and turn on the fuel shut-off valve. The engine is now ready to start by following the starting

instructions listed below. With the engine running, move the hydraulic valve lever toward the wedge. This will cause

the cylinder to extend and expel air. When the cylinder is fully extended, retract it. Repeat this procedure several

times. (An erratic movement of the cylinder and wedge indicates that there is air in the system). Once the cylinder has

a smooth and constant speed indicating that all air has been expelled, shut the system off and refill the reservoir until

the fluid is in the safe operating range as specified by the marks on the dipstick.

START UP

WARNING: DO NOT START OR RUN THE LOG SPLITTER WITHOUT OIL IN THE ENGINE

AND HYDRAULIC RESERVOIR.

See separate Engine Manual for fuel and oil recommendations. Your log splitter has come equipped with a fuel shut-

off valve for storage and towing purposes. The engine will only start when the throttle lever and fuel shut-off valve are

turned to their ON positions.

*STARTING INSTRUCTIONS

*See the engine manufacturers operating manual for starting and maintenance instructions.

NOTE: For cold engine starting “choke” may be required. The choke position of the throttle lever is the extreme up

position, full throttle is the detent position just slightly lower than the choke position.

1. Put the key into the ignition switch.

2. Turn the key to the START position on the ignition

switch. Usually engine will start within 3 seconds

3. When engine starts, position the throttle control at “FAST.” The throttle must be set in the fast position for

maximum performance.

4. To stop engine, move throttle lever to “SLOW” for a few seconds then turn the ignition key to the “OFF”

position.

IMPORTANT: This engine is not equipped with a spark arrester muffler. It is a violation of California

Public Resource Code Section 4442 to use or operate the engine on any forest-covered, brush-

covered, or grass-covered land. Other states or federal areas may have similar laws.

4-WAY WEDGE OPERATION: See 18851 Owners Manual in parts bag.

SPLITTER OPERATION

1. Set up the log splitter in a clear, level area and block the wheels. The suction port on the tank should always

be on the lower side of the log splitter.

2. Place a log on the beam, against the foot plate. Make sure the log is securely on the foot plate and up against

the beam.

3. Depress the valve lever so that the cylinder will drive the wedge into the log. Extend the cylinder until the

log splits or to the end of its stroke. If the log has not completely split after the cylinder has reached the end

of its extension, retract the cylinder, reposition log and repeat process. NOTE: Leaving the valve in the

“actuate” position at the end of the stroke may damage the pump. Always use extra care when splitting logs

with ends that are not square.

NOTE: To extend the life of the hydraulic cylinder, avoid “BOTTOMING OUT” the cylinder.

4. When using the Log Splitter in the vertical position, make sure the beam latch is engaged as shown below.

Pull the bent pin outward then twist and release it to hold the I-beam in place.

TOWING SAFETY

This unit should not be towed on any street, highway, or public road without checking the existing federal, local, and

state laws. Any licensing or modifications such as taillights, etc., need to comply with existing federal, local, or state

vehicle requirements is the sole responsibility of the purchaser. Obey all regulations when towing on public roads and

highways. See also SAFETY PRECAUTIONS.

*Turn the fuel shut-off valve OFF to prevent flooding of the engine while traveling.

*Ensure that 4-way wedge is placed securely in the towing position, fastened to the motorbase or in

the towing vehicle.

*Be careful when backing up. You can easily jack-knife your splitter.

TOWING AT NIGHT

The requirements for taillights are based on States regulations. Some states allow towing at night as long

as the towed equipment does not visibly impair the tow vehicle taillights. This is based on a state, to state

requirements. The customer is responsible for meeting the states requirements.

If a “Statement of Origin” is required in your state, see your local dealer to receive one.

HYDRAULIC SAFETY

The hydraulic system on your splitter requires careful inspection along with the mechanical parts. Be sure to replace

any frayed, kinked, cracked or otherwise damaged hydraulic components. Just because it isn’t leaking today doesn’t

mean that it will not fail tomorrow.

MAINTENANCE AND STORAGE

WARNING: DISCONNECT THE SPARK PLUG BEFORE PERFORMING ANY MAINTENANCE.

Consult the operating and maintenance instructions of the engine manufacturer for engine care.

Always check the oil level of the hydraulic reservoir before operation. Operating without an adequate oil

supply will cause severe damage to the pump. Change the hydraulic fluid in the reservoir after every 100 hours of

operation. Change the hydraulic filter after every 50 hours of operation (use only a 10 micron hydraulic filter).

Periodically check that all nuts, bolts, screws, clamps and fittings are tight and secure.

To keep your splitter in top working condition perform all recommended maintenance procedures before you use

your splitter.

If the wedge becomes dull or nicked a grinder or sharpening tool can be used to sharpen it.

Completely drain the fuel tank prior to storage. Always store gasoline in an approved, tightly sealed container. Store

container in a dry, cool place with adequate ventilation. Keep fuel away from areas where fumes could contact open

flame, pilot light or sparks.

Be aware of the environment when disposing of used petroleum products. Please dispose of used hydraulic

fluid, engine oil and any by products from the maintenance of your splitter at approved recycling centers.

Should it become necessary to disassemble the unit for repair or replacement of parts, refer to the drawings and parts

list on the following pages. Exercise extreme caution, as some parts are very heavy and will require sufficient

persons or mechanical handling equipment.

Your Swisher Log Splitter has been produced with components designed specifically to this machine. Although

standard springs, hardware and ect may look similar to parts used on other machinery, they may in some cases

be made of a different construction and/or materials. All replacement parts must meet manufacturer’s

specifications.

The operation of any splitter can produce foreign objects which can be thrown

into the eyes, resulting in severe eye damage. Always wear certified safety

glasses or wide-vision safety goggles over spectacles before staring any

splitting machine and while operating such a machine.

The operation of any splitter produces sound waves that are damaging to the

human ear. Ear protection is recommended.

*Fluid escaping from a very small hole can almost be invisible. Do not check for leaks with your hand. Escaping

fluid under pressure can have sufficient force to penetrate skin causing serious personal injury or even death.

Leaks can be detected by passing a piece of cardboard or wood over the suspected leak and looking for

discoloration. IF injured by escaping fluid, see a doctor at once. Serious infection or reaction can develop if

proper medical treatment is not administered immediately.

*Should it become necessary to loosen or remove any hydraulic fittings, lines or reservoir cap, be sure to relieve

all pressure by shutting off the engine and moving the control handle back and forth several times.

*NEVER remove the cap from the hydraulic tank or reservoir while the unit is running. Hot oil under pressure

could result in serious injury. See also SAFETY PRECAUTIONS.

The pressure relief valve on your splitter is preset at the factory. DO NOT adjust the valve. Only a

qualified technician should perform this adjustment.

*NEVER run the log splitter for extended periods of time without cycling the cylinder. Running the unit

without cycling hydraulic fluid throughout the entire system will cause excessive heat build up in all

components.

12494 – HYDRAULIC FILL PLUG

DECAL

11427 – DANGER DECAL

12492 – OPERATOR INSTRUCTION

DECAL

OD16 – FUEL SHUT OFF DECAL

SAFETY DECALS

Replace decals immediately if damaged.

12549 – DO NOT EXCEED 45 MPH

DECAL

12532 – HYDRAULIC OIL DECAL

ASSEMBLY DETAIL

Item # Part # Description

17296K Tire/Wheel, Log Splitter; Blk

2 NB179 Washer - 3/4 ID X 1 1/4 OD 18 GA ZY

3 2203CN Nut - Castle 3/4-16, .625 Tall, Grade 2

4 NB633 Pin - Cotter, 1/8 X 2(Ext Prng Crbn Stl)

5 2203DC Cover - Dust, Wheel Hub

6 NB151 Bolt - 1/2-13 X 6 HCC GR5 ZP

7 NB555 Washer - USS Flat, 1/2 ZY

8 NB688 Nut - Nyloc Jam, 1/2-13 ZY

9 18839TK Weldment - Wedge, 4-Way; Txt Blk

10 NB587 Bolt - Carriage, 5/16-18 X 1 3/4 ZY Gr 2

11 2030 Knob - Black Plastic

12 20077TK Weldment - Motorbase, LS; Txt Blk

NOT SHOWN 20081 Hose - Hydraulic Return, 3/4"ID X 61"

NOT SHOWN 22419 Coil Cover - Return Hose, 5'

NOT SHOWN 19165 Hose - Hydraulic Pressure, 60"

NOT SHOWN 19811 Coil Cover - Pressure Hose, 5'

NOT SHOWN 20080 Hose - Suction

ASSEMBLY DETAIL

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Swisher Holzspalter Handbücher

Swisher

Swisher LSRB675221350 Bedienungsanleitung

Swisher

Swisher LS12534HPF Bedienungsanleitung

Swisher

Swisher LS87522BP Bedienungsanleitung

Swisher

Swisher L112-182001 Bedienungsanleitung

Swisher

Swisher L111-283044 Bedienungsanleitung

Swisher

Swisher L113-074001 Bedienungsanleitung

Swisher

Swisher L113-305001 Bedienungsanleitung

Swisher

Swisher LSED14534 Bedienungsanleitung

Swisher

Swisher LSRB10528 Bedienungsanleitung

Swisher

Swisher LS10534D Bedienungsanleitung

Swisher

Swisher LS622 Bedienungsanleitung

Swisher

Swisher LS722X Bedienungsanleitung

Swisher

Swisher LSER11534 Bedienungsanleitung

Swisher

Swisher LSEB125341350 Bedienungsanleitung

Swisher

Swisher LS422X Bedienungsanleitung

Swisher

Swisher LS722A Bedienungsanleitung

Swisher

Swisher LSRH4422 Bedienungsanleitung

Swisher

Swisher LS5-24 Bedienungsanleitung

Swisher

Swisher LS728A Bedienungsanleitung

Swisher

Swisher LS3P Bedienungsanleitung

Swisher

Swisher LS87522HP Bedienungsanleitung

Swisher

Swisher LS12534H Bedienungsanleitung

Swisher

Swisher 21200 Bedienungsanleitung

Swisher

Swisher LSRB125341350 Bedienungsanleitung

Beliebte Holzspalter Handbücher anderer Marken

Bell

Bell Pickpine VS S9 Gebrauchsanweisung

ATIKA

ATIKA ASP 5 N-UG Betriebsanleitung

Posch

Posch Schälprofi 500 Bedienungsanleitung

Champion

Champion 91520 Handbuch

Fieldmann

Fieldmann FZLS 1008V-E Bedienungsanleitung

Craftsman

Craftsman 247.28775 Bedienungsanleitung

Scheppach

Scheppach OX 3-1000 Montageanleitung

Elem Garden Technic

Elem Garden Technic FBHT65-22TCH Bedienungsanleitung

Champion Power Equipment

Champion Power Equipment 90720 Handbuch

Boss Industrial

Boss Industrial ES5T20 Bedienungsanleitung

Villager

Villager LSP 12 T Bedienungsanleitung

MTD

MTD 242-642A Bedienungsanleitung

Rok

Rok 150-51-50255 Bedienungsanleitung

Hakki Pilke

Hakki Pilke Raven Bedienungsanleitung

Hyundai

Hyundai HYLS7TE Bedienungsanleitung

Scheppach

Scheppach HL1500M Benutzerhandbuch

Craftsman

Craftsman 247.794510 Bedienungsanleitung

Zipper Mowers

Zipper Mowers ZI-HS5TN Bedienungsanleitung