Swisher PC-300 Bedienungsanleitung

Powered Cart

Powered CartPowered Cart

Powered Cart

OWNER’S

MANUAL

1602 CORPORATE DRIVE, P.O. BOX 67, WARRENSBURG, MISSOURI 64093

P ONE (660) 747-8183 FAX (660) 747-8650

MODEL NO.

Manufacturing quality lawn care equipment since 1945

Assembly

Operation

Service and Adjustment

Repair Parts

Made In The

USA

Read and follow all Safety

Rules and Instructions

before operating this

equipment.

PC-300

swisherinc.com

ONPC300

REV. 05-108

LIMITED WARRANTY

The manufacturer’s warranty to the original consumer purchaser is: This product is free from

defects in materials and workmanship for a period of one ( ) year from the date of purchase by

the original consumer purchaser. We will repair or replace, at our discretion, parts found to be

defective due to materials or workmanship. This warranty is subject to the following limitations

and exclusions:

) Engine Warranty All engines utilized on our products have a separate warranty

extended to them by the individual engine manufacturer. Any

engine service difficulty is the responsibility of the engine

manufacturer and in no way is Swisher Mower Co., Inc. or its

agents responsible for the engine warranty. The Briggs & Stratton

Engine Service Hot-Line is -800-233-3723. The Transmission

Service Hot-Line is -800-558-5402.

2) Commercial Use The warranty period for any product used for commercial or rental

is limited to ninety (90) days from the date of original purchase.

3) Limitations This warranty applies only to products which have been properly

assembled, adjusted, and operated in accordance with the

instructions contained within this manual. This warranty does not

apply to any product of Swisher Mower Co., Inc., that has been

subject to alteration, misuse, abuse, improper assembly or

installation, shipping damage, or to normal wear of the product.

4) Exclusions

Excluded from this warranty are normal wear, normal adjustments,

and normal maintenance.

In the event you have a claim under thi

s warranty, you must return the product to an authorized

service dealer. All transportation charges, damage, or loss incurred during transportation of parts

submitted for replacement or repair under this warranty shall be borne by the purchaser. Should

you have any questions concerning this warranty, please contact us toll-free at -800-222-

8 83.

The model number, serial number, date of purchase, and the name of the authorized Swisher

dealer from whom you purchased the product will be needed before any w

arranty claim can be

processed.

THIS WARRANTY DOES NOT APPLY TO ANY INCIDENTAL OR CONSEQUENTIAL

DAMAGES AND ANY IMPLIED WARRANTIES ARE LIMITED TO THE SAME TIME

PERIODS STATED HEREIN FOR ALL EXPRESSED WARRANTIES. Some states do not

allow the limitation of

consequential damages or limitations on how long an implied warranty

may last, so the above limitations or exclusions may not apply to you. This warranty gives you

specific legal rights and you may have other rights, which vary from state-to-state. This

is a

limited warranty as defined by the Magnuson-Moss Act of 975.

OPERATING YOUR NEW PC-300

INTENDED USE

• This machine is designed for moving objects and other materials normally moved by a

wheelbarrow.

• The three-speed transaxle system with engagement bail and forward/reverse

control delivers smooth steady performance.

• The dump latch allows for easy dumping and offers a spring-loaded return of the

latch mechanism when the bed is returned from the dump position.

• The PC-300 is designed to carry 300 pounds- DO NOT EXCEED

MANUFACTURER’S SET WEIG T LIMIT!

Assembly of PC 300

• Remove PC300 from crate. Be careful not to damage the idler cable (item 3 , p 8).

• Align holes in handle and frame and bolt together using; (4) NB604, 3/8 – 6 X ”

bolt, (8) NB27 , 3/8 USS washer, (4) NB 82, 3/8 – 6 Nyloc nut.

• Bolt bed lift handle to bed using; (4) NB604, 3/8 – 6 X bolt, (4) NB272, 3/8 SAE

washer and (4) NB27 , 3/8 USS washer, (4) NB 82, 3/8 – 6 Nyloc nut. Place the

smaller washer (NB272) on the outside of the handle.

• Assemble (2) NB 39, ¼ - 20 hex nuts to modified J-bolts (item 26, p 8), nuts should

be tightened against the end of the bolt threads. Reference Shift Rod/Handle detail

p. 8 and secure J-bolts to the handle, shift rod weldment (item 25, p 8) and shift rod

half (item 3, p 9) using (2) NB 80, ¼ - 20 Nyloc nuts.

The operation of any equipment can encounter foreign objects which could be

thrown into the eyes, resulting in severe eye damage. Always wear certified safety

glasses or wide-vision safety goggles over spectacles before starting machine and

while operating such a machine.

The operation of any engine produces sound waves that are damaging to the

human ear. Ear protection is recommended.

CAUTION!

Tragic accidents can occur if the operator is not alert to the presence of

children. Children are often attracted to the machine and the hauling

activity. Never assume that children will remain where you last saw them.

SLOPE OPERATION!

Use extra caution when operating on slopes. Operate self-propelled units

up and down slopes. There is a significant risk of overturns when

operating across slopes. If you feel uneasy on a slope then do not

operate on it.

STOPPING T E ENGINE

• Slide the throttle into the

“STOP” position.

STARTING T E ENGINE

• Remove any built-up debris from

engine.

• Check oil & fuel.

• Prime engine as directed. Note:

A warm engine may not need to

be primed.

• Slide throttle into “FAST”

position.

• Pull engine coil rope. Do not pull

recklessly.

• Adjust throttle to desired engine

RPM. For maximum results,

operate in the full throttle

position.

PREPARING FOR FIRST USE

• Check engine crankcase for oil.

Check with engine dipstick. Do

not overfill. See engine manual

for proper oil level.

• Fill fuel tank with fresh gasoline.

Never fill tank in an enclosed

area!

• Start engine as directed above.

• Stop engine.

BEGIN USING

• Make sure area is clear of all

bystanders.

• Make sure that all guards, belt

guides, and the spark plug wire

are properly attached.

• Adjust handle height. Loosen black

plastic knob on each side of the

control panel. Move handle to

desired height. Retighten black

plastic knobs.

• Start engine, setting desired

engine speed. Note: This

machine is designed to operate at

maximum engine speed.

• Start by shifting the unit into a

low gear. Begin forward

movement by slowly lifting

control bail toward handle. To

stop the unit, release the bail and

move the shift lever into the

neutral position.

BACKING T E UNIT

• Always look behind and down to

avoid obstacles and tripping.

• Shift lever into reverse position

and slowly lift control bail

towards handle. To stop the unit,

release the bail and move the

shift lever into neutral.

SUGGESTED PRACTICES

• Do not operate cart if it vibrates

abnormally. Excessive vibration

is a sign of damage. Stop the

engine and safely check for

damage. Repair as necessary.

• Do not operate the cart with the

dump bed in the up (dump)

position.

CAUTION!

SHUT OFF ENGINE AND REMOVE

WIRE FROM SPARK PLUG BEFORE

MAKING ANY ADJUSTMENTS TO

THE UNIT.

CAUTION!

TO ENSURE SAFE OPERATION, THE

OPERATOR MUST HOLD THE

HANDLEBARS WITH BOTH HANDS.

PC -3 00 M A IN T E N A N C E & SE R V IC E

ST O R A G E

• D o not sto re engine indo ors or o ther

poorly v entilated areas.

• If u nit is to be stored for longer than 30

days, prepare as directed below :

• D rain fuel ou tsid e in to an approved

container

• S tart engine and run u ntil unit is

com pletely ou t of fuel. R em oving fuel

prevents gu m dep osits from fo rm ing

inside carburetor. G u m depo sits can

cause th e engin e to m alfunction.

• Let engine cool.

SEA SO N A L M A IN T E N A N C E

• R eplace th e spark plug.

• C lean or rep lace th e air filter and fuel .

• C hange oil.

• C heck belts, tires, hardw are, etc. for w ear

and dam age. R epair as necessary.

N O T E : N ew spark plug, clean air filter, and

clean fuel filter insure proper air-fuel m ixture

and h elp the en gine p erform better and last

longer.

B E FO R E E A C U S E

• C heck and fill engine oil on a level

surface. If oil appears black or so iled,

change im m ediately.

• C heck con dition of filters, spark plug,

tires, etc. C lean or replace if necessary.

• C heck for loose hardw are and tighten as

needed .

B E L T A D JU ST M E N T

• S to p engine and rem ove spark plug w ire.

• T he belt tension is adjusted by turning the

cable trun nion o n the idler cable located

under the con trol p anel.

• P ull hairpin and rem ove w asher from

cab le trunnion.

• P ull trunn ion out of the ho le in the

handle.

• T urn trunnio n tow ard op erator to

increase belt tension.

• Insert the trunnion into th e han dle.

• R eplace w asher and hairpin.

• R econnect spark plug w ire.

B E L T R E PLA C E M E N T

•

Stop engine and rem ov e w ire from spark

plug.

• R em ove idler pulley (#T3 0V )

• R em ove old belt.

• Inst

all new belt. S tart at the engine pu lley

and w ork the belt aro und the drive p ulley

and onto th e backside of the idler pulley.

•

R eplace idler pulley. M ak e sure belt guide

does not m ake contact w ith belt.

• R econnect the spark plu g w ire.

B elt C on figu ration

(S om e parts rem ov ed fo r clarity)

C A U T IO N !

SH U T O F F EN G IN E A N D R E M O V E

W IRE F R O M SP A R K P LU G B EF O R E

M A K IN G A N Y A D JU ST M E N T S T O

T H E U N IT .

B ottom V iew

U S E P R O PER T O O LS F O R

A N Y A D JU S T M EN T S ,

D ISA S S E M B LY , O R

R E PA IR S .

T30V

SAFETY PRECAUTIONS & DECALS

• Read the manual. Learn to operate this machine safely.

• Always disconnect the spark plug wire and place the wire where it cannot contact

the spark plug, to prevent accidental starting the engine when setting up,

transporting, adjusting or making repairs.

• Keep all shields and guards in place.

• Understand the speed, steering and stability of this machine. Know the positions

and operations of all controls before you operate this machine. Check all of the

controls in a safe area before starting to work with this machine.

• Allow only responsible adults who are familiar with these instructions to operate

this machine. Never allow children to operate this machine.

• Clear the area of objects such as rocks, toys, wire, etc. that can cause the cart to

become unbalanced and tip over.

•

Never assume that children will remain where you last saw them.

Keep

children under the watchful care of another responsible adult.

• No riders!

• Do not put hands or feet near or under rotating parts.

• Always look down and behind before and while backing.

• Watch for traffic when operating near or crossing roadways.

• Do not operate the cart if it has been dropped or damaged in any manner or if the

cart vibrates excessively. Excessive vibration is an indication of damage. Repair

as necessary.

• Dress properly. Do not operate when barefoot or wearing open sandals. Wear

only solid shoes with good traction.

• Do not operate the machine while under the influence of alcohol or drugs.

• Never tamper with safety devices. Check their proper operation regularly.

• Stop and inspect the equipment if you strike an object. Repair, if necessary,

before restarting.

• Never make adjustments or repairs with the engine running.

This Safety Alert Symbol indicates important messages in this

manual. When you see this symbol, carefully read the message

that

follows and be alert to the possibility of personal injury.

Read this manual completely. This machine can amputate hands, feet, and throw

objects. Failure to observe the following safety instructions could result in serious

injury or death.

PC-300 Assembly

Frame Detail

(See page 9 and 0)

Console Detail

(See

FRONT/ TRANSAXLE DETAIL

PAGE 4

FRAME DETAIL

PAGES 0 &

BED DETAIL

PAGE 3

HANDLE DETAIL

PAGE 8

ENGINE DETAIL

PAGE 9

andle Detail

Item Qty Part # Description Item Qty Part # Description

1 1

3311TK

Bail Weldment Painted

18 1 NB275 5/16 SAE Washer

2 1

3333TK

Control Panel Weldment Painted 1 1 NB125 1/8 X 3/8 Cotter Pin

3 1

3334TK

Handle Weldment Painted 20 2 3357 Bail Handle Grip

4 8 NB604 3/8 -16 X 1 GR5 ZP Bolt 21 1 335 Z Cable Trunnion Zinc Plated

5 2 NB516 5/16-18 X 1 Carriage Bolt 22 1 NB127 #3 Hair Pin

6 2 2030 Black Plastic Knob 23 1 NB556 5/16 USS Flat Washer ZP

7 8 NB182 3/8-16 Nyloc Nut 24 12 NB272 3/8 USS Washer

8 6 NB742 Washer Internal-External Tooth 25 1 3377 Shift Rod Half Weldment

2 7478 Handle Grip 1 1/8" X 8" 26 2 3378 Modified J-Bolt

10 1 4857 Plastic Knob- Black 27 3 NB180 1/4-20 Nyloc Nut

11 1 NB280 3/8-16 2-Way Lock Nut 28 8 NB271 3/8 USS Washer

12 1 NB741 1/2-13 X 5 HTC GR5 ZP 2 1 3322TK Shifter Weldment

13 1 NB177 1/2 NR Machine Bushing 14 Ga. 30 1 ES130TK Spacer Rolled 3/4 OD X 1/2 ID X 1

14 2 NB555 1/2 USS Flat Washer ZP 31 1 3337 Idler Cable

15 1

NB213Z

1/2-13 Nut ZP 32 1 023MOD Clutch Cable Clevis T44CH

16 1 633 Hold Dow n Spring 33 1 NB250 1/4 - 20 X 3/4 GR5 ZP

17 1

NB281

1/2-13 Nyloc Nut

34 2 NB13 1/4 - 20 Hex Nut

OD 7 Shift/Safety Decal for PC300

Qty ( )

OD99 25 Medium Swisher Logo White Decal

Qty ( )

23 2

7 4 6

24 4

5 30 4 2

34 25 27

SHIFT ROD/HANDLE

DETAIL

Frame Detail

ITEM

QTY.

PART DESCRIPTION ITEM

QTY.

PART DESCRIPTION

1 1 3318TK Belt Dampener 15 2 3301-BC Bed Pivot Tab

2 12 NB5 6 5/16 -18 X 3/4 Serr Flg Bolt 16 1 NB522 1/4 X 1 Clevis Pin

3 14 NB170 5/16 - 18 Serrated Flange Nut 17 1 NB735 1/4 - 28 Yoke End ZP

4 1 See P. 12 Idler Assembly 18 1 3342C Pulley Cover

5 1 334 Brake Cable 1 1 3302C Latch Reinforcement

6 1 3355TK Bell Crank Assy 20 1 331 BC Cross Member Bolted

7 1 NB220 1/2 X 1 - /16 Shoulder Bolt 21 1 3353 Engagement Rod

8 1 NB182 3/8 - 16 Nyloc Nut 22 1 NB272 3/8 SAE Washer

1 NB121 1/2 - 13 2 Way Jam Lock Nut 23 1 3340TK Shift Linkage

10 4 NB275 5/16 SAE Washer 24 1 NB263 Ball Linkage Right

11 2 NB125 1/8 X 3/4 Cotter Pin 25 1 NB734 1/4 - 28 X 5/8 GR8 ZP

12 1 3348 Brake Spring 26 1 NB274 1/4 SAE Washer

13 1 3362 Shift Rod Half 27 1 NB448 5/16 - 24 ZP 2 Way Lock Nut

14 1 3300BC Frame Base (Bolted) 28 1 NB708 3/32 X 1 Cotter Pin

2 1 3337 Idler Cable

OD 7

New Serial # Decal

Qty ( )

OD 72

Over laminate

Qty ( )

822

325

23 24

Engine Detail

ITEM NO. QTY. PART NO. DESCRIPTION

1 1 3320 Belt Snubber ZP

2 1 NB138 5/16 - 18 X 2 1/2 HCC GR5 ZP

3 2 NB556 5/16 USS Flat Washer ZP

4 1 NB505 5/16 - 18 X 1 1/2 HCC GR5 ZP

5 1 NB253 5/16 - 18 X 1 1/4 Serr. Flange Bolt

6 1 NB170 5/16 - 18 Serr. Flange Nut

7 2 NB558 5/16 - 18 ZP 2 Way Lock Nut

8 1 NB745 Hex Cap Screw GR5 ZP 3/8 - 24 X 2

1 6 Washer Belleville Engine Pulley

10 1 EBS675LS Briggs 6.75 OHV Splitter Engine

11 1 3350EXT Ext Motor Pulley 3"

12 1 3375 3/16 X 2 Key Stock

13 1 AS021 Cable Tie - Black 5 1/2" (Not Shown)

Andere Swisher Outdoor-Wagen Handbücher

Swisher

Swisher FC-10 DUMP CART Bedienungsanleitung

Beliebte Outdoor-Wagen Handbücher anderer Marken

Costway

Costway TH10057 Bedienungsanleitung

Vivo

Vivo CART-PC02S Bedienungsanleitung

Ergotron

Ergotron STYLEVIEW SV42-3162-1 Bedienungsanleitung

VEVOR

VEVOR SC01 Bedienungsanleitung

Carts Vermont

Carts Vermont 20 Bedienungsanleitung

Vivo

Vivo CART-PC01 Bedienungsanleitung

Costway

Costway TL0400 Bedienungsanleitung

XPOtool

XPOtool 30261 Bedienungsanleitung

Branick

Branick 130 Gebrauchs- und Pflegehandbuch

Anthro

Anthro PrinterCart Bedienungsanleitung

Westward

Westward 2CZY4 Service-Handbuch

Hupfer

Hupfer TTW/V Bedienungsanleitung

Gorilla Carts

Gorilla Carts GCR-10P Bedienungsanleitung

Numatic

Numatic EcoMatic EM-5 Bedienungsanleitung

Bosch

Bosch XL-Cart Montageanleitung

Tennsco

Tennsco Modular Cart Top Component Assembly Bedienungsanleitung

Makita

Makita DCU601 Bedienungsanleitung

Clam

Clam POLAR TRAILER HD MAX Bedienungsanleitung