Swiss Madison Avancer Smart Toilet Bedienungsanleitung

www.swissmadison.com | 1-434-623-4766 | [email protected]

INSTALLATION INSTRUCTIONS

Avancer Smart Toilet

@SwissMadison

#WellMadeForever

TOUCHLESS

technology

well made for e v e r

If you have any questions or concerns please contact us:

1-434-623-4766

[email protected]

PRIOR TO INSTALLATION:

· Inspect toilet to ensure no damages have occurred while in shipping.

· Observe all plumbing and building codes in accordance with your state and local requirements.

· All dimensions are nominal! Be sure to measure your toilet prior to installation.

· The step-by-step guidelines in the installation instructions are a general reference. Should there be

any discrepancies, Swiss Madison cannot be held liable. It is recommended to install all Swiss

Madison products by hiring a licensed professional.

· Read installation and maintenance instructions thoroughly before installing. Be sure to use proper

tools and always wear proper personal safety accessories for your protection.

· Two people are recommended to handle and install this product as it is fragile.

INCLUDED PARTS:

SUGGESTED TOOLS & MATERIALS:

Safety

Glasses Wrench

Tape

Measure Level

—1 —

SMART TOILET INSTALLATION INSTRUCTIONS

Tankless

Toilet

Angle Valve Sealing

Flange

Floor Anchor

Kit

Remote

Braided

Hose

Sealant Bucket Drill

—2 —

SMART TOILET INSTALLATION INSTRUCTIONS

· Automatic Flushing: Toilet will automatically flush as

you walk away from the bowl. When the user sits less than

60 seconds it will activate a half flush. When the user sits for

more than 60 seconds, it will activate a full flush.

· Side Manual Flush: Press the knob on the side of the toilet

to manually activate a full flush.

· Foot-Sensor Flushing: Tap the foot sensor area to activate

a half flush.

· Soft-Close Seat.

· Heated Seat: Adjust 6 level seat temperature with the

remote. The seat temperature will automatically lower to

level 1 after 10 minutes.

· Bidet Wash: Rear and front massage wash with 6 level

water temperature adjustment and 3 level water pressure

adjustment.

· Self-Cleaning: Self-cleaning, anti-bacterial spray nozzle,

anti-bacterial seat.

· Night Light: Smart white night light, normally off.

· User Settings: Adjustable male and female automatic wash

settings to personalize your experience.

PRODUCT FEATURES: SPECIFICATION PARAMETERS:

· Requires power to operate

· Requires one 9V battery for back up flushing

· Rated Voltage: 110V-120V

· Rated Power: 1200-1400W

· IP Rating: IPX4

· Flush Volume: Full flush 1.6 GPF / Half flush 1.1 GPF

· Flush Type: Vortex™

· Rough-in: 12”

· Waste Outlet: S-trap 12”

· Outer Outlet Diameter: 3.5”

· Water Pressure Range: 0.09MPa ( dynamic water

pressure, flow rate 4 gal/min or more) - 0.8MPa (static

water pressure)

· Bidet Heating Power: 1400W

· Drying Heating Power: 250W

· Warm Air Volume: Over 7 ft³ / min

Knob

Remote

sensing window

Heated

drying fan

Rear

cleaning

Spray

nozzle

Front

cleaning

27 ³⁄16”

18 ³⁄4”

15 9⁄16”

16 ³⁄4”

Off-seat flush

sensor

REMOVABLE

STICKER

Foot flush

sensor

REMOVABLE

STICKER

TOILET INSTALLATION:

—3 —

SMART TOILET INSTALLATION INSTRUCTIONS

2. Rough-In & Install Angle Valve

· Measure the wall from behind the toilet to the

middle of the floor drain. Your rough-in measurement

should be 12”.

· Install angle valve at proper position on the wall

according to toilet inlet placement.

· Align cardboard with the centerline of the drain outlet,

then draw a contour line according to the cardboard.

1. Check Pressure

· The minimum dynamic working water pressure

is 0.09MPa or more (4 gal/min or more), failure

to meet this pressure will not achieve the best

flushing effect.

If you do not have a water pressure testing

device, open the angle valve and connect water

inlet for 10s, once the water volume is above

0.66 gal, the minimum water pressure of the

product is ensured.

Angle valve

(included)

Hose (included)

Bucket

Nut

Bolt

3. Install Mounting Bracket

· Assemble the mounting bracket with bolts

and then install them to the pre-installed flange

plate on the ground and lock tight with nuts.

Mounting bracket

Washer

4. Connect to Water Supply

· Connect the water inlet and angle valve of the

toilet with the matching hose and tighten it.

Floor drain

Mating

angle valve

Rough-in

Cardboard

cutout

12”

2 ³⁄4”

Angle valve Inlet connector

Flexible hose

—4 —

SMART TOILET INSTALLATION INSTRUCTIONS

8. Connect Power

· Insert power line leakage protection plus into the

power socket. Press the reset switch and look for

the indicator lights to indicate the power is on.

Once connected to power, the toilet will beep and

the knob will light up and start self testing. After

self testing is complete, the knob will light up and

proceed to normal function.

NOTE: Press electric leakage test button prior to

usage, the reset switch pops up indicating

that the leakage protection function is normal.

Press the TEST button (then RESET button)

every month to assure proper operation.

6. Install Toilet

· Install toilet by putting sealing flange into drain

outlet. This sould be done by two people, the

toilet is heavy.

5. Turn on Angle Valve

· Check thread connection and check for leaks.

Unscrew angle valve counterclockwise to open

all the way.

NOTE: When opening for the first time, the

angle valve handle has a larger torque.

7. Secure Toilet

· Put the screw through the anchor and

then install it through the holes on both sides of

the toilet to the mounting bracket and tighten.

· Cover installation bolts with bolt covers.

· Apply a thin bead of sealant around toilet base.

Anchor

Screw

Bolt cover

Toilet drain outlet

Sealing flange

Electric leakage

test button

Reset switch

Indicator light

—5 —

SMART TOILET MAINTENANCE & USAGE

MAINTENANCE

1. Daily Usage Caution

· Turn off power supply before cleaning.

· Use only a soft, damp cloth to clean the toilet. Avoid using harsh chemicals.

2. Cleaning Filter

· The filter should be cleaned if the water pressure is normal, but the toilet is not flushing normally.

· Disconnect the power supply and turn off water supply at the angle valve.

· Unscrew angle valve nut and remove.

· Remove filter net and use a brush to clean.

· Re-install filter and angle valve nut, turn on the angle valve and connect power.

3. Spray Nozzle Maintenance & Care

· Nozzle will self clean when the user gets off the seat. Rotate the knob clockwise to manually clean

the nozzle, the knob will automatically extend and flush nozzle with water.

· To dissemble the nozzle, wait until it moves forward, then disassemble and clean. Do not pull or

push the wand to avoid damage. Use a soft cloth or brush to clean. When cleaning is finished, put

the nozzle back into the toilet and press the “stop” button to automatically retract the nozzle.

—6 —

SMART TOILET MAINTENANCE & USAGE

USAGE

1. Manual Flushing

· Press the knob to manually activate a full flush.

2. Activating Foot Sensor Flushing

· To turn on foot-sensor flushing, press the “STOP” and

the “FULL FLUSHING” button on the remote

simultaneously. Repeat to turn off.

· This function will not work while the user is sitting.

3. Knob Functions

· Rotate clockwise to start rear cleaning, rotate counterclockwise to start front cleaning. Rear and front

cleaning will automatically enter drying mode after completion.

· If user is not seated and the knob is rotated clockwise, manual nozzle cleaning will begin.

· After starting the rear and front cleaning, turn the knob clockwise to move the spray rod forward, and

counterclockwise to move the spray rod backwards. Hold down the knob to switch to the water

pressure adjustment mode. Turning the knob clockwise in this mode will increase the water pressure,

and counterclockwise will decrease the water pressure. Hold the knob again to switch back to spray

rod position adjustment mode.

· After starting the drying function, turning the knob clockwise will increase the wind temperature, and

counterclockwise will decrease the wind temperature.

· Press the knob at any time to stop the current function. Pressing the knob after functions stop will

flush the toilet.

· Hold down the knob after use to turn off the toilet and put it in standby mode, the light will turn off. In

power saving mode, the light will breathe.

· If the toilet is in standby mode, press the knob to enter normal working mode.

4. Battery Installation & Replacement

· Pull out the power plug and turn of water supply.

· Fully open the seat and cover, take out the left and right decorative covers, unscrew the screws

counterclockwise, and take out the gasket.

· Pull up the cover slightly with both hands so the back end of the cover is separated from the ceramic

positioning column, you may hear a “clicking” sound.

· Pull out the plug-in connecting line, loosen the water inlet pipe and remove the whole seat and cover.

· Place the seat flat with bottom facing up, be careful not to scratch the top of the seat.

· Remove the battery box cover from the bottom of the seat to install or replace the 9V battery.

· Place the battery cover over the new battery then turn on water supply and power.

NOTE: Optional for back up flushing use only, battery not included. screw

battery cover

battery (not included)

screw

decorative cover

washer

Knob

—7 —

SMART TOILET TROUBLESHOOTING

TROUBLESHOOTING

1. How to flush without water supply:

· Put around 2.1 gal of water into a bucket and pour into bowl to flush.

2. What to do when not in use for a long period of time (over three days):

· Unplug and remove the battery box and all batteries.

· Drain out water by flushing the toilet after turning off the angle valve to prevent water from entering.

· Drain out water inside pipe by unscrewing the hose from the angle valve, draining, then re-installing.

· It is suggested to put antifreeze inside the bowl to prevent any remaining water from freezing.

· When ready to use again, reconnect water and power supply.

PROBLEM CAUSE SOLUTION

Not Flushing

Water supply hose is buckling and causing a

block. Solve the buckling.

Fill valve is off.

Water supply is cut off. Connect water supply and wait for the water.

Poor Flushing

Water supply hose is buckling and causing a

block. Solve the buckling.

Fill valve is not fully turned on.

Low Water Temperature Water temperature is set to normal. Reset the water temperature.

Low Seat

Temperature

Seat temperature is set to normal. Reset the seat temperature.

In standby mode. Switch to normal function mode and wait 3

minutes before use.

Low Wind

Temperature Wind temperature is set to normal. Reset the wind temperature.

No Wind In standby or power saving mode. Shift to function mode.

Spray Wand Not Retracting

Power is off. Push back the wand lightly and wait for power.

Clogged by impurities. Clear away the impurities.

Spray Wand Not Extending

Power is off. Push back the wand lightly and wait for power.

Not sitting in the sensing area. Sit in the sensing area.

Remote Not Working Reverse the polarity of the battery. Reload the battery.

CAUTION

If the problems cannot be solved as per above methods, please disconnect power and contact

Swiss Madison for maintenance.

If the leakage circuit breaker trips off often, the product has an electric leakage. Shut off the power

and contact Swiss Madison for maintenance.

—8 —

SMART TOILET TROUBLESHOOTING

WARNINGS

DANGER - To reduce the risk of electrocution:

Do not use while bathing.

Do not place in or drop into water or other liquid.

Do not reach for a product that has fallen into water. Unplug immediately.

Do not wash the main unit or electrical plug with water or detergent.

Do not handle the electrical plug with wet hands.

Do not put a hand or other staff over the outlet of air dryer or block the outlet of air dryer.

Never disassemble,repair or modify this product.

During installation, disassembly, repaire and maintenance of the product,the power plug must be switched off

and water supply be shut off.

WARNING - To reduce the risk of burns, electrocution, fire, or injury to persons.

Close supervision is necessary when this product is used by, on, or near children.

Use this product only for its intended use as described in this manual. Do not use attachments not

recommended by the manufacturer.

Never operate this product if it has a damaged cord or plug, if it is not working properly, if it has been dropped

or damaged, or dropped into water. Return the product to a service center for examination and repair.

Keep the cord away from heated surfaces.

Never use while sleeping or drowsy.

Never drop or insert any object into any opening or hose.

Do not use outdoors, operate around aerosol (spray) products or where oxygen is being administered.

Connect this product to a properly grounded outlet only. See Grounding Instructions.

Do not throw cigarettes and other burning stuff into toilet, otherwise it might cause fire.

This product is electric appliance, so it must be placed far away from water. Please don’t drenchwith liquid.

Do not lay on side or upside the product during the electrical circuit.

It is prohibited to use other electric appliances in the same socket.

It is forbidden to use the power extension or unstable loose outlet.

The old aging water supply hose can not be used, otherwise it might cause leakage, fire or electrical shock.

Installation of the bidet seat should include specified components and new water supply hose.

Do not place or store product where it can fall or be pulled into a tub or sink.

—9 —

SMART TOILET SAFETY

IMPORTANT SAFETY INSTRUCTIONS

1. Do not install or use the product in wet places as steam room etc.

2. It is recommended to use water-proof electrical outlet which should be lnstalled in the place

where is not easily got wet.

3. This product should be used with 110V-120V,50/60Hz electrical current only,load current

is at least 15A. Power plug must be equipped with ground fault circuit interrupter or ground

fault electrical leakage protector or similar high sensitive, rapid type leakage switch

(Rated sensitive current under 6mA).

4. When it thunders,it is strongly recommended to pull out the power plug.

5. Do not stand on ceramic toilet.

6. Ceramic toilet must install floor fixing bolt.

7. Do not stand on product unit,seat and cover.

8. Do not lean against the seat cover when using the product,to avoid damage.

9. This product is equipped with soft-closing seal cover.Heavy pressing or pushing may damage

the soft-closing damper.

10. Do not use lacquer thinner,petrol,liquid medicine,detergent,insecticide,toilet cleanser and

scrubbing brush to clean the product.

11.Exposure to direct sunlight is prohibited.

12.Only use tap water or potable water;otherwise it may cause chafing.

13.Do not connect water supply to heater outlet.Make sure inlet water temperature at

14.When the room temperature is under zero degree,please dry up the water tank, to avoid freezing.

15.Raise rest room temperature to prevent the toilet from damage due to freezing.

16.When move the product from cold or wet environment into normal room temperature,wait for

2 hours until the condensation water is fully volatilized.Doing so can prevent the product from

electrical short-circuit.

17.When not using the product over three(3) days,drain the water out of the container and pull

the electrical plug from the wall outlet.

18.Stop using the product and shut off the power when product malfunctions,please contact the

service people for professional service.

CAUTION - Failure to follow the instruction may cause injury or property damage.

GROUNDING INSTRUCTIONS

This product should be grounded. In the event of an electrical short circuit, grounding reduces

the risk of electric shock by providing an escape wire for the electric current. This product is

equipped with a cord having a grounding wire with a grounding plug. The plug must be plugged

into an outlet that is properly installed and grounded.

DANGER - Improper use of the grounding plug can result in a risk of electric shock.

If repair or replacement of the cord or plug is necessary, do not connect the grounding wire to

either flat blade terminal. The wire with insulation having an outer surface that is green with or

without yellow stripes is the grounding wire.

This product is factory equipped with a specific electric cord and plug to permit connection to a

proper electric circuit. Make sure that the product is connected to an outlet having the same

configuration as the plug. No adapter should be used with this product. Do not modify the plug

provided — if it will not fit the outlet, have the proper outlet installed by a qualified electrician. If

the product must be reconnected for use on a different type of electric circuit, the reconnection

should be made by qualified service personnel.

37.4~95 F

。

Inhaltsverzeichnis

Andere Swiss Madison Toilette Handbücher

Swiss Madison

Swiss Madison Ivy SM-1T127 Bedienungsanleitung

Swiss Madison

Swiss Madison SM-WT514MB Bedienungsanleitung

Swiss Madison

Swiss Madison SM-WK465-01C Bedienungsanleitung

Swiss Madison

Swiss Madison SM-WC424 Bedienungsanleitung

Swiss Madison

Swiss Madison Avallon SM-1T121 Bedienungsanleitung

Swiss Madison

Swiss Madison SM-STS21 Bedienungsanleitung

Swiss Madison

Swiss Madison St. Tropez SM-1T254 Bedienungsanleitung

Swiss Madison

Swiss Madison SM-WT449 Bedienungsanleitung

Swiss Madison

Swiss Madison Sublime SM-1T205 Bedienungsanleitung

Swiss Madison

Swiss Madison SM-1T206BQ Bedienungsanleitung

Swiss Madison

Swiss Madison SM-WT555 Bedienungsanleitung

Swiss Madison

Swiss Madison Virage SM-1T118 Bedienungsanleitung

Swiss Madison

Swiss Madison SM-2T130 Bedienungsanleitung

Swiss Madison

Swiss Madison Sublime II SM-2T257 Bedienungsanleitung

Swiss Madison

Swiss Madison Monaco SM-WT460 Bedienungsanleitung

Swiss Madison

Swiss Madison Cache SM-2T220 Bedienungsanleitung

Swiss Madison

Swiss Madison Sublime II SM-1T257 Bedienungsanleitung

Swiss Madison

Swiss Madison SM-WT450 Bedienungsanleitung

Swiss Madison

Swiss Madison Carré SM-1T264 Bedienungsanleitung

Swiss Madison

Swiss Madison SM-WT514 Bedienungsanleitung

Swiss Madison

Swiss Madison St. Tropez SM-1T253 Bedienungsanleitung

Swiss Madison

Swiss Madison SM-WT442 Bedienungsanleitung

Swiss Madison

Swiss Madison SM-1T113 Bedienungsanleitung

Swiss Madison

Swiss Madison Nadar SM-2T141 Bedienungsanleitung

Beliebte Toilette Handbücher anderer Marken

Toto

Toto Washlet TCF4911 Series Bedienungsanleitung

Kohler

Kohler K-6419 Bedienungsanleitung

Grohe

Grohe Sensia ARENA Bedienungsanleitung

Kohler

Kohler K-5171K Montageanleitung

Geberit

Geberit AQUACLEAN MERA CLASSIC Bedienungsanleitung

Kohler

Kohler K-24097X Montageanleitung

Better Bathrooms

Better Bathrooms BUN/BeBa 27555/78725 Bedienungsanleitung

American Standard

American Standard CONCEPT Cube TF-2704 Bedienungsanleitung

BIOLAN

BIOLAN ECO Stücklistenhandbuch

Thetford

Thetford C260 Series Bedienungsanleitung

KELISS

KELISS T162A Series Bedienungsanleitung

Kohler

Kohler K-22241K Montageanleitung

Kohler

Kohler ESCALE K-32771T-NS Bedienungsanleitung

BIOLAN

BIOLAN GARDEN TOILET Stücklistenhandbuch

washloo

washloo Prestige Bedienungsanleitung

JABSCO

JABSCO 37010 Series Bedienungsanleitung

Olympia

Olympia EPOQUE 69209 Bedienungsanleitung

DENCK

DENCK PURE-D Bedienungsanleitung