Thomann
GmbH
•
Hans-
Thomann-Straße
1
•
96138
Burgebrach
•
www
.thomann.de
•
[email protected] DocID: 503272_25.11.2020HDbaseT HDMI2.0 Extender 100m
EN
Quick start guide
This quick start guide contains important information on the safe operation of the
product. Read and follow the safety advice and instructions given. Retain the quick
start guide for future reference. If you pass the product on to others please include this
quick start guide.
For the transport and protective packaging, environmentally friendly materials
have been chosen that can be supplied to normal recycling. Ensure that plastic
bags, packaging, etc. are properly disposed of. Do not just dispose of these ma-
terials with your normal household waste, but make sure that they are collected for recy-
cling. Please follow the notes and markings on the packaging.
This product is subject to the European Waste Electrical and Electronic Equip-
ment Directive (WEEE) in its currently valid version. Do not dispose of your old
device with your normal household waste. Dispose of this product through an
approved waste disposal rm or through your local waste facility. Comply with
the rules and regulations that apply in your country. If in doubt, consult your local waste
disposal facility.
Features
• Transmits an uncompressed HDMI signal over a CAT5e / 6 / 6a / 7 cable
• Supports Full-HD 1080p60 up to 4K×2K @ 60Hz
• Suitable for distances up to 100 meters
• Transmission protocol: HDbaseT
• Bidirectional transmission of IR signals
• Supports HDCP, CEC and 24 deep color as well as LPCM audio and compressed audio
such as DTS-HD and Dolby True HD
• Scope of delivery: HDbaseT transmitter, HDbaseT receiver, 2×IR transmitter / receiv-
er cables, 2×power adapters
Safety instructions
Intended use
This device is used to transmit HDMI signals via network cables. Any other use or use
under other operating conditions is considered to be improper and may result in per-
sonal injury or property damage. No liability will be assumed for damages resulting
from improper use.
Danger for children
Ensure that plastic bags, packaging, etc. are disposed of properly and are
not within reach of babies and young children. Choking hazard! Ensure
that children do not detach any small parts from the product. They could
swallow the pieces and choke!
Where to use the product
Never use the product
• in conditions of extreme temperature or humidity
• in extremely dusty or dirty areas
• at locations where the unit can become wet
General handling
• To prevent damage, never use force when handling the product.
• Never immerse the product in water. Just wipe it with a clean dry cloth. Do not use
liquid cleaners such as benzene, thinners or ammable cleaning agents.
Using the product
1. Connect both devices using the supplied power supplies with properly wired
wall outlets. The respective Power indicator (1) lights up, the devices are imme-
diately ready for operation.
2. Connect the HDMI source to the INPUT HDMI socket of the transmitter using a
suitable cable. Its LED (3) lights up when connected and a signal is present.
3. If you want to control the display connected to the receiver via infrared from the
position of the transmitter, connect one of the infrared cables to the IN IR socket
of the transmitter and one to the OUT IR socket of the receiver. The diode at the
end of the cable must point to the IR sensor on the display. You can nd out
where this sensor is located in the operating instructions for the display.
4. Connect the HDBT OUT socket of the transmitter to the HDBT IN socket of the
receiver using a CAT5e / 6 / 6a / 7 cable (max. length 100m). The LEDs (2) on both
devices light up to conrm the established connection.
qINPUT HDMI –HDMI input
wIN IR –connection for infrared receiver
eOUT IR – connection for infrared transmitter
r12V 1A –connection for power adapter
t1 2 3 –control LEDs for device functions
1: LED lights up when device is supplied with voltage
2: LED lights up when the connection between
transmitter and receiver is established
3: LED lights up when there is a connection to the HDMI
signal source and a signal is present
yHDBT OUT –HDBaseT signal output
5. Connect the HDMI display to the OUTPUT HDMI socket of the receiver using a
suitable cable. The LED (3) lights up when there is a connection and a signal is
present.
6. If you want to control the HDMI source with its IR remote control from the loca-
tion of the receiver, connect one of the infrared cables to the IN IR socket of the
receiver and one to the OUT IR socket of the transmitter. The diode at the end of
the cable must point to the IR sensor on the HDMI source. You can nd out where
this sensor is located in the operating instructions for the HDMI source.
7. Switch on the HDMI devices and start the transmission on the HDMI source.
8. After use, disconnect both power adapters from the power supply.
Transmitter
Receiver
uOUTPUT HDMI –HDMI output
iIN IR –connection for infrared receiver
oOUT IR –connection for infrared transmitter
a12V 1A –connection for power adapter
s1 2 3 –control LEDs for device functions
1: LED lights up when device is supplied with voltage
2: LED lights up when the connection between
transmitter and receiver is established
3: LED lights up when there is a connection to the HDMI
display and a signal is present
dHDBT IN –HDBaseT signal input
Operating elements
