SycoTec E@syDrive 4638 Bedienungsanleitung

Short Instruction For Use EN

HF Inverter e@syDrive® 4638

Distribution:

SycoTec GmbH & Co. KG

Wangener Strasse 78

88299 Leutkirch, Germany

Phone +49 7561 86-0

Fax +49 7561 86-371

info@sycotec.eu

www.sycotec.eu

Manufacturer:

SIEB & MEYER AG

Auf dem Schmaarkamp 21

21339 Lüneburg, Germany

Phone +49 (0)4131 203-0

Fax +49 (0)4131 203-2000

info@sieb-meyer.de

www.sieb-meyer.com

This short instruction for use includes only the essential control functions.

It does not however replace the Sieb & Meyer Hardware Description "Drive System

SD2S" that must be downloaded before commissiong:

- on the SycoTec homepage at the download area under

https://www.sycotec.eu/en/about-sycotec/downloads2/

respectively

- at Sieb & Meyer under

https://www.sieb-meyer.com/file-detail.html?item=421

The safety information have to be observed before commissioning!

 
 
EN 
 
Content 
 
0 Scope of Supply and Accessories 4 
1 Scope of Supply 4 
2 Accessories 4 
0 Connections 4 
0 Safety Circuit and Restart Lock 4 
0 Motor 5 
1 Motor Temperature Sensor 5 
2 Assignment of the Parameter Sets 5 
3 Connection choke 6 
0 Power Supply 6 
0 Digital and Analog Inputs / Outputs 6 
1 Digital inputs 7 
2 Digital Outputs 7 
3 Analog Inputs 8 
0 External Ballast Resistor 8 
0 Example of remote control element 9 
0 Connecting to the computer 9 
0 Activate another parameter set 10 
0 Load parameter file 10 
0 Load Project 11 
0 Status Display and Error Messages 12 
Warranty Conditions 13 
CE Declaration of Conformity 13 
 
 

1.0 Scope of Supply and Accessories

1.1 Scope of Supply

HF Inverter e@syDrive® 4638 Material no. 2.001.6091

(Drive System SD2S / device variant 0362121EC)

SycoTec –Short Instruction For Use Material no. 2.001.8020

HF Inverter e@syDrive® 4638

1.2 Accessories

Motor choke (220 µH, 12 Aeff) Material no. 2.002.2384

Ballast resistor (400 W, 10 Ohm) Material no. 2.002.2385

2.0 Connections

3.0 Safety Circuit and Restart Lock

The power supply unit is only activated when SAFEA and SAFEB are connected. If the safety function is not

required, pin1 and pin 3 must be bridged to pin 5.

Name

I/O

Meaning

SAFEA

Enable of safety circuit

X10/1

SAFEB

Enable of safety circuit

X10/3

24 V

Logic voltage 18 –28 V

X10/6

The 24V output is not suited to supply external safety circuits.

4.0 Motor

Name

I/O

Meaning

Motor phase U

X22A/U

Motor phase V

X22A/V

Motor phase W

X22A/W

Protective conductor

X22A/PE

4.1 Motor Temperature Sensor

Name

I/O

Meaning

Temp

Motor temperature sensor (towards GND)

X16/9

GND

I/O

Ground

X16/11,12

4.2 Assignment of the Parameter Sets

Assignment

Parameter set of motor spindle

Remark

P00

4060 E

P01

4060 ER

P02

4060 ER-S

P03

4060/4061 AC

P04

4060 AC-T

P05

50100 AC-duo

P06

4060/4061 DC-S_SVC

Motor spindle must be operated with an

upstream choke / external inductance of

220 µH

P07

4060/4061 DC-T_SVC

P08

4064 DC SK_SVC

P09

4064 DC HSK_SVC

P10

5045 DC-HV 60.P4_SVC

P15

4060/4061 DC-S_HSPWM

Alternative function types, without choke

P16

4060/4061 DC-T_HSPWM

P17

4064 DC_HSPWM

4.3 Connection choke

The connection X22A (Motor) of the frequency inverter is connected to connection X1 (Drive) of the choke.

The motor phases are connected to X2 (Motor) of the choke.

X1 (Drive)

X2 (Motor)

Name

Meaning

Pin (Choke)

Name

Meaning

Pin (Choke)

Motor phase U

X1/U

Motor phase U

X2/U

Motor phase V

X1/V

Motor phase V

X2/V

Motor phase W

X1/W

Motor phase W

X2/W

Protective conductor

X1/

Protective conductor

X2/

5.0 Power Supply

Name

I/O

Meaning

Main supply

X28/L1

Main supply

X28/L2

Protective conductor

X28/PE

Voltage range: 150 V AC -10% to 230 V AC +10%

6.0 Digital and Analog Inputs / Outputs

If you want to make use of the digital inputs and outputs, connect pin x15/9 to 24 V.

The functions / assignments of the inputs and outputs can be configured via the "drivemaster2" software.

By default, the following functions / assignments are set.

6.1 Digital Inputs

Name

I/O

Function / Assignment

IN0

Switch on

X16/1

IN1

Operation enable

X16/2

IN2

Error reset

X16/3

IN6

Speed direction

X16/7

GND

I/O

Ground

X16/11,12

VCC-IO

24 V supply for IO

X15/9

VCC-OUT

24 V output for IO (max. 0,3 A)

X15/10

IN0 "Switch on" activates the controller, the holding current is applied to the motor spindle.

If the controller is active, the motor spindle can be started with IN1 "Operation enable".

[*] Yet another digital input is located at the connector X15, pin 6.

6.2 Digital Outputs

Name

I/O

Function/Assignment

OUT0

Ready type 1

X15/1

OUT1

M02 - Message operation enabled

X15/2

OUT2

M12 - Speed zero

X15/3

OUT3

M10 - Ref. value reached

X15/4

VCC-IO

24 V supply for IO

X15/9

VCC-OUT

24 V output for IO (max. 0,3 A)

X15/10

GND

I/O

Ground

X15/11,12

Every output can be loaded with 100 mA.

6.3 Analog Inputs

Name

I/O

Function/Assignment

AIN0+

Speed reference value

X18/3

GND

I/O

Ground

X18/4

AIN0-

Reference point for AIN0+ (bridge with ground)

X18/7

VCC_10

10 V supply voltage

X18/9

Voltage interface with input voltage range: ± 10 V

Can also be connected to potentiometer (500 Ohm –5 kOhm

7.0 External Ballast Resistor

Name

Function / Assignment

Rextern

External ballast resistor

X41/1

Rintern

Internal ballast resistor

X41/2

UB+

X41/3

If no external ballast resistor is used, pin 1 and pin 2 of connector X41 must be bridged.

The technical data of the optionally connected external ballast resistor must be entered via the

"drivemaster2" software.

By default no external ballast resistor is set.

8.0 Example of remote control element

9.0 Connecting to the computer

➢Connect the inverter via USB interface to the computer

➢Plug in the inverter

➢Start Sieb & Meyer "SD2 Windows software drivemaster2"

https://www.sieb-meyer.com/file-detail.html?item=413

To establish a connection to the device click "Setup connection to the device", adjust "USB" for connection

type and select "Search devices + connect".

10.0 Activate another parameter set

To activate a different parameter file, enter the number (P00 … Pxx) of the required parameter file and click

"Apply".

11.0 Load parameter file

Before opening the parameter file select the right position (Pxx) or add a new parameter set.

Inhaltsverzeichnis

Andere SycoTec Gleichstromantrieb Handbücher

SycoTec

SycoTec HF Inverter e@syDrive 4624 Bedienungsanleitung

Beliebte Gleichstromantrieb Handbücher anderer Marken

Vincent Associates

Vincent Associates UNIBLITZ ED12DSS Bedienungsanleitung

EKSMA OPTICS

EKSMA OPTICS DQ-100-4 Stücklistenhandbuch

Chamberlain Garog

Chamberlain Garog D Series Bedienungsanleitung

Parker

Parker PDS Series Bedienungsanleitung

Festo

Festo DGC G Series Einrichtungshandbuch

Binks

Binks QS-5012-1-CE Bedienungsanleitung

Danfoss

Danfoss VLT 2800 Series Technisches Datenblatt

ABB

ABB ACQ580-01 Series Installationshandbuch

YASKAWA

YASKAWA CANopen SI-S3 Bedienungsanleitung

GE D20A6 Bedienungsanleitung

Unex

Unex MC-D-250-1000-050W-TW Bedienungsanleitung

Geckodrive

Geckodrive G213V Bedienungsanleitung

ABB

ABB RSYC-01 Bedienungsanleitung

Rockwell Automation

Rockwell Automation PowerFlex 700S Betriebsanleitung

WEG

WEG DeviceNet CFW500 Bedienungsanleitung

Siemens

Siemens SINAMICS G Datenblatt

Siemens

Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Betriebsanleitung

SOMFY

SOMFY JR RU 30 Bedienungsanleitung

SycoTec e@syDrive 4638 Bedienungsanleitung

Beliebte Gleichstromantrieb Handbücher anderer Marken