SYMA X5C Bedienungsanleitung
-5-
The transmitter built-in two modes, Mode 1 & Mode 2, in
line with different customer’s usage pattern. Keep pushing
button B to right, than turn on the transmitter power to
change Mode 1 or Mode 2.
CONTROLLER MODES & INSTRUCTIONS
1.When charging, please put this product on a dried or ventilated area and keep
it far away from heat source or explosive product.
2.When charging, please remove the batteries from the quadcopter. Then
charging process should be supervised by an adult so as not to cause an
accident.
3.After flying, please do not charge the battery if the surface temperature is still
not cool. Otherwise it may cause a swollen battery or even a fire hazard.
4.Please make sure that you use the original USB charging cable provided.When
the battery has been used for a long time, or appears to be swollen, please
replace them.
5.A battery when not in use for a long time will lose its charge automatically.
Charging or discharging too often may reduce the life of the battery.
CAUTIONS WHEN CHARGING
1.Battery should be put in the dried or ventilated place with enviroment
temperature about 18-25℃.
2.In order to enhance the using life of the battery, please avoid repeat charging
or excessive discharging.
3.When the battery needs to be stored for a long time,please charge the battery
first.That is to say, charge the battery for about 50-60% of the volume and then
well store it.
4.If you do not use it for more than 1 months, it’s highly recommended that you
need to check the battery voltage every month so as to make sure the voltage
no less than 3V. Otherwise please do by following No.(3) mentioned.
1.Install the landing skids to the bottom of quadcopter (Figure 1).
2.Install the blade protecting frame to every corner than lock screws (Figure 2).
BATTERY REPAIR & MAINTENANCE
B
Figure.1 Figure.2
INSTALL LANDING SKIDS & BLDAE PROTECTING FRAME
-6-
MODE 1
Operating direction
Hover up and down Forward and backward
Push the throttle up or down, the
quadcopter flies upward or downward.
Push the direction lever up or down, the
quadcopter flies forward or backward.
Sideward fly
Turn Left and Right
Pull the direction lever left or right, the
quadcopter flies to left side or right side.
Pull the throttle left or right, the
quadcopter turns to left or right.
Fine-tuning operation
Turn left/right fine-tuning
Sideward fly fine-tuningForward/Backward fine-tuning
When the quadcopter keeps
flying forward / backward, you
can correct it by pressing
fine-tuning button down / up.
When the quadcopter keeps
flying to left / right side, you
can correct it by pressing the
Fine-tuning button right / left.
When the quadcopter keeps
rotating to left /right, you can
Correct it by pressing the
fine-tuning button right / left.
-7-
MODE 2
Operating direction
Hover up and down Forward and backward
Push the throttle up or down, the
quadcopter flies upward or downward.
Push the direction lever up or down, the
quadcopter flies forward or backward.
Sideward fly
Turn Left and Right
Pull the throttle left or right, the
quadcopter flies to left side or right side.
Pull the direction lever left or right, the
quadcopter turns to left or right.
Fine-tuning operation
Turn left/vright fine-tuning
Sideward fly fine-tuningForward/Backward fine-tuning
When the quadcopter keeps
flying forward / backward, you
can correct it by pressing
fine-tuning button down / up.
When the quadcopter keeps
flying to left / right side, you
can correct it by pressing the
fine-tuning button right / left.
When the quadcopter keeps
rotating to left /right, you can
Correct it by pressing the
fine-tuning button right / left.
-8-
INTRODUCTION TO QUADCOPTER FUNCTIONS
3m
3D EVERSION AND THROWING FLIGHT INSTRUCTIONS
Tips:3D eversion goes better when battery
power is enough.
When you are familiar with the basic
operation, you can do some awesome
& exciting tricks and stunts! First of all,
fly the aircraft to a height of more than
3 meters, press the 3D Eversion switch
on the rear right side of the transmitter,
then push the right rudder(in any direction)
to make 360 degree flip.
①.Press the power switch to turn on
the transmitter.
Low-voltage protection:
When the quadcopter battery is not enough， the rotors will be stopped power
supply.As the quadcopter control systemwill protected battery automatically.
Over-current protection:
When the quadcopter’s rotating blade is collided or jammed, the control system
will stop supplying power for the rotors automatically, Then please re-match the
signal for flying.
Restart function:
In case of flight disorder or sideward flight, restore factory default settings by the
following methods:
②.Press the power switch to turn on the quadcopter.
③.When the quadcopter indicator quickly flashing
to slowly flashing,please push the throttle lever to
the highest position,and then pull it back to the
lowest position.Then the quadcopter indicator
changed from slowly flashing to normal lights up.
④.Place the quadcopter on a horizontal postion,
then push transmitter both left and right lever to
lowest right conner for about 2-3 second ,
indicator on the quadcopter changed from normal
lights up to quickly flashing ;After 2-3 second ,the
indicator changed to normal lights,it means the
quadcopter restarted /reset successfully.
Andere Handbücher für X5C
1
Inhaltsverzeichnis
Andere SYMA Drohne Handbücher
SYMA
SYMA GYRO REMOTE CONTROL SERIES Bedienungsanleitung
SYMA
SYMA LOG1628-R2 Bedienungsanleitung
SYMA
SYMA X220W Bedienungsanleitung
SYMA
SYMA HD 8500WH Bedienungsanleitung
SYMA
SYMA GC88752-13 Bedienungsanleitung
SYMA
SYMA GC88752-30 Bedienungsanleitung
SYMA
SYMA GYRO REMOTE CONTROL SERIES Bedienungsanleitung
SYMA
SYMA GC88752-28 Bedienungsanleitung
SYMA
SYMA X300 Bedienungsanleitung
SYMA
SYMA Z3 Bedienungsanleitung
SYMA
SYMA X8C Bedienungsanleitung
SYMA
SYMA X12S Explorers Bedienungsanleitung
SYMA
SYMA X200W Bedienungsanleitung
SYMA
SYMA Z3 Bedienungsanleitung
SYMA
SYMA LOG1612-JR Bedienungsanleitung
SYMA
SYMA X200 Bedienungsanleitung
SYMA
SYMA X400 Bedienungsanleitung
SYMA
SYMA X110W Bedienungsanleitung
SYMA
SYMA X800W Bedienungsanleitung
SYMA
SYMA X5UW-D Bedienungsanleitung
