Symantec ASG-S400-20 Bedienungsanleitung

ASG-S400-20 to -30 Upgrade Kit

Product Installation Guide

Legal Notice

and the Blue Coat logo are trademarks or registered trademarks of Symantec Corp. or its affiliates in the U.S. and other

countries. Other names may be trademarks of their respective owners. This document is provided for informational

purposes only and is not intended as advertising. All warranties relating to the information in this document, either

express or implied, are disclaimed to the maximum extent allowed by law. The information in this document is subject to

change without notice.

THE DOCUMENTATION IS PROVIDED "AS IS" AND ALL EXPRESS OR IMPLIED CONDITIONS,

REPRESENTATIONS AND WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY,

FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT, ARE DISCLAIMED, EXCEPT TO THE

EXTENT THAT SUCH DISCLAIMERS ARE HELD TO BE LEGALLY INVALID. SYMANTEC CORPORATION SHALL

NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IN CONNECTION WITH THE

FURNISHING, PERFORMANCE, OR USE OF THIS DOCUMENTATION. THE INFORMATION CONTAINED IN

THIS DOCUMENTATION IS SUBJECT TO CHANGE WITHOUT NOTICE. SYMANTEC CORPORATION

PRODUCTS, TECHNICAL SERVICES, AND ANY OTHER TECHNICAL DATA REFERENCED IN THIS

DOCUMENT ARE SUBJECT TO U.S. EXPORT CONTROL AND SANCTIONS LAWS, REGULATIONS AND

REQUIREMENTS, AND MAY BE SUBJECT TO EXPORT OR IMPORT REGULATIONS IN OTHER COUNTRIES.

YOU AGREE TO COMPLY STRICTLY WITH THESE LAWS, REGULATIONS AND REQUIREMENTS, AND

ACKNOWLEDGE THAT YOU HAVE THE RESPONSIBILITY TO OBTAIN ANY LICENSES, PERMITS OR OTHER

APPROVALS THAT MAY BE REQUIRED IN ORDER TO EXPORT, RE-EXPORT, TRANSFER IN COUNTRY OR

IMPORT AFTER DELIVERY TO YOU.

Symantec Corporation

350 Ellis Street

Mountain View, CA 94043

www.symantec.com

5/19/2017

Symantec Upgrade Installation Guide

Contents

Upgrading the ASG-S400-20 to the ASG-S400-30 4

Review Kit Contents 5

Required Installation Tools 6

Prepare the Appliance for Upgrade Kit Installation 7

Shut Down the Advanced Secure Gateway Appliance 8

Install Additional S400 Series Hard Disk Drives 9

Open the S400 Series Center Cover 11

Remove the S400 Series Rear Cover 13

Remove the S400 Series Airduct 14

Install the ASG-S400 Memory Modules 15

Install an S400 Series Processor and Heatsink 18

Install the S400 Series Airduct 22

Reinstall the S400 Series Rear Cover 23

Close the S400 Series Center Cover 24

Finish the Upgrade Process 25

Verify the ASG Appliance Hardware Configuration 27

Troubleshooting 29

Appendices 30

SafetyWarnings and Cautions 31

Appliance Specifications 33

Hard Disk Drive Status LEDs 38

S400 Series Hard Drives 39

S400 Hard Drive Configuration Table 40

Symantec Upgrade Installation Guide

Upgrading the ASG-S400-20 to the ASG-S400-30

To install an upgrade kit for the ASG-S400 Series appliance, follow the tasks listed below for your upgrade kit. Please

note, a qualified technician must perform the following tasks in order to reduce the risk of damage to your appliance.

Review the "SafetyWarnings and Cautions" on page31 before servicing your appliance. ALWAYS observe proper

electrostatic discharge (ESD) conventions. Attach an ESD protective wrist strap to your wrist and to the chassis.

Ensure that the appliance is on an ESD-safe work surface or ground the unit appropriately. Symantec does not

assume responsibility or liability for damage resulting from ESD.

Follow the steps below to install the components of the upgrade kit.

1. Verify the contents of the upgrade kit.

2. Gather the required tools for installation.

3. Prepare the appliance for upgrade kit installation. Archive the configuration settings running on the old appliance

and record your network configuration settings.

4. Gracefully shutdown the appliance.

5. Install three additional HDDs into empty drive bay 4, 5, and 6.

6. Open the center cover.

7. Remove the rear cover.

8. Remove the airduct.

9. Replace the existing memory modules with those included with the kit.

10. Replace the CPU and heatsink unit.

11. Reinstall the front airduct.

12. Reinstall the rear cover.

13. Close the center cover.

14. Finish the upgrade process. (Connect the cables, power on, install license).

15. Verify the new hardware configuration.

16. Troubleshooting

Be sure to recycle your old and unused hardware through the Symantec Recycling Service. For more information,

go to https://www.bluecoat.com/support/support-policies/recycling-blue-coat-products

Symantec Upgrade Installation Guide

Review Kit Contents

The contents of the ASG-S400-20 to -30 upgrade kits are shown below. Please verify the contents of the upgrade kit

before continuing with the installation. If any items are missing, please contact your Symantec Support contact for

assistance.

Model Upgrade Kit Contents

ASG-S400-20 to ASG-S400-30

Upgrade Kit

Hard Disk Drives: 1TB HDD x 3

Memory: 48GB (8GB X 6)

Processor: 6 Core Intel CPU x 1

Heatsink: Heatsink unit with pre-applied thermal compound x 1

Miscellaneous: ESD Wriststrap, Information Flyer

Symantec Upgrade Installation Guide

Required Installation Tools

To install the S400 upgrade kit, Symantec recommends the following tools and items.

Item Description

Required Tools #2 Phillips head screwdriver

Recommended Items Mechanical lift (if moving the appliance to a separate workspace)

Flashlight or headlamp

Thumb protector (to use when pressing DIMMs into sockets)

Symantec Upgrade Installation Guide

Prepare the Appliance for Upgrade Kit Installation

Before performing any hardware upgrades, archive the configuration and keyring that are running on the old appliance and

record your network configuration settings. This should be done periodically as part of general system maintenance

procedures.

IMPORTANT:

nKeys are exported in clear text with no encryption or obfuscation. Take precautions to secure the archive file

appropriately.

nThe archive does not include keyrings saved with the Do not show keypair option. For keyrings that are not

included in the archive, you must manually create a new keyring and import the key and the certificate into the new

ProxySG appliance before you are instructed to restore this archive.

Create a back up of your SGOS configuration using SSH-Console session. The archive generated in this procedure

includes the showable keyrings on the appliance.

1. In your terminal emulation application, enable session logging. Configure the application to log the session output

and save that file on your local system. The following example uses PuTTY:

2. Access the CLI on the appliance and enter the following commands from the CLI command prompt:

SGOS> enable

SGOS# config terminal

SGOS(config) show configuration noprompts with-keyrings

SGOS(config) exit

3. Exit the terminal emulation application, making sure that session logging is turned off.

4. Open the session log/output file and delete all the text/commands before and after the configuration.

5. Save this text file on your local system or hard drive.

6. Record your network settings (Management interface IP address, subnet mask, default gateway, primary DNS

server, alternate DNS server).

Symantec Upgrade Installation Guide

Shut Down the Advanced Secure Gateway Appliance

Gracefully shut down and power off the Advanced Security Gateway appliance using the CLI shutdown command. Do

not shut down the appliance using the switch or by removing the power cables! Abruptly removing power can result in

irreparable data loss. Always use the CLI shutdown command to power down the appliance.

Remove the power cords

after

the appliance has been properly shut down.

To gracefully shutdown the appliance using the shutdown command:

1. Review the safety warnings before proceeding. See "SafetyWarnings and Cautions" on page31.

2. Access the ASG command-line interface using a terminal emulation program.

3. When prompted, press 1to access the CLI.

4. Enter enable to access privileged commands.

5. Enter shutdown to turn off the appliance.

6. Unplug the power cord(s) from the AC power outlet(s).

7. Disconnect the power cord(s) from the power supply unit(s).

8. Be sure to properly ground the chassis before continuing with the installation.

Symantec Upgrade Installation Guide

Install Additional S400 Series Hard Disk Drives

The S400 Series appliances are available in configurations with a maximum of 8 hard disk drives for SAS-based

appliances and 2 for SATA-based appliances. Each HDD is equipped with a LEDstatus indicator and are hot-swappable

on certain Symantec appliances. SATA drives can only be removed and installed when power is disconnected from the

appliance. Depending upon the model and configuration of the appliance, some drive bays might be populated with empty

drive carriers. These carriers should not be removed when the appliance is in operation.

For information on where to install hard disk drives, refer to the S400 Series HDD configuration table.

1. Pull the appliance out of the rack (or set the appliance over the workspace edge) several inches to provide room for

the bezel.

2. Open the bezel to access the HDD quick release carriers. Be sure to support both sides when flipping over the

bezel.

3. Properly orientate the new HDDcarrier with the chassis HDD bay and slide into the appliance until it reaches the

chassis stops and secure the drive by closing the latch until it clicks into place.

Note: Do not insert the HDDcarrier with the latch in the closed position! Instead, push the HDD carrier body to

avoid damaging the carrier.

Symantec Upgrade Installation Guide

4. Close the appliance bezel.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Symantec Firewall Handbücher

Symantec

Symantec SSL Visibility SV3800 Bedienungsanleitung

Symantec

Symantec 10521148 - Network Security 7161 Bedienungsanleitung

Symantec

Symantec 10744983 - Mail Security 8320 Bedienungsanleitung

Symantec

Symantec 10268947 - Network Security 7160 Bedienungsanleitung

Symantec

Symantec 10521146 - Network Security 7120 Bedienungsanleitung

Symantec

Symantec 10521146 - Network Security 7120 Bedienungsanleitung

Symantec

Symantec 10547829 - Mail Security For Smtp 5.0 Smb Bedienungsanleitung

Symantec

Symantec 16-00-00091 - FNC XGRD FW VPN 200 Bedienerhandbuch

Beliebte Firewall Handbücher anderer Marken

Cisco

Cisco S190 Bedienungsanleitung

Fortinet

Fortinet FortiGate Voice Series Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 2300 Bedienungsanleitung

SecureLogix

SecureLogix ETM System Bedienungsanleitung

NETGEAR

NETGEAR ProSafe FVX538 Bedienungsanleitung

Lanner

Lanner FW-8877 Bedienungsanleitung

Huawei

Huawei USG6000 Series Installations- und Betriebshandbuch

H3C

H3C SecPath F5000-AI-15 Bedienungsanleitung

Nexcom

Nexcom DNA 1150 Bedienungsanleitung

Fortinet

Fortinet FortiGate-60 series Bedienungsanleitung

Cisco

Cisco 3110 Handbuch

Draytek

Draytek Vigor2860 Series Bedienungsanleitung

Lanner electronics

Lanner electronics FW-7650 Series Bedienungsanleitung

Swisscom

Swisscom Internet Backup Bedienungsanleitung

SonicWALL

SonicWALL NSa 5700 Bedienungsanleitung

DPtech

DPtech FW1000 SERIES Bedienungsanleitung

FEITIAN

FEITIAN MultiPass FIDO Bedienungsanleitung

EBLOCKER

EBLOCKER PRO Bedienungsanleitung