Synairgy SACDD-24 Bedienungsanleitung

www.hoses.co.uk

www.synairgy-eu.com

Direct Driven Compressor Operation Manual

Model No. SACDD-24/50

www.hoses.co.uk

Direct Driven Compressor Operation Manual Model No. SACDD-24/50

Important Notice 3

First Time Usage 3

Preparation for Usage 4

Safety Guidelines 4-5

Caution 6

Brief Description 6

Compressor Overview 7

Technical Speciﬁcation 7

Parts List 8-9

Operation and Adjustment 10

Maintenance 10

Troubleshooting 11

Contents

www.hoses.co.uk

1. In order to operate this compressor, please read and fully understand the instructions

contained in this manual before use. The compressor should only be operated by professional

personnel who fully abide by the safety instructions contained herein.

2. Keep the compressor away from ﬂammable materials and heat sources.

3. Switch off the power supply and release the compressed air before each maintenance or

repair. Ensure warning stickers are displayed to avoid accidental use during this period.

4. It is strictly prohibited to change the factory’s settings without manufacturer’s prior

written consent.

www.synairgy-eu.com

Important Notice

First Time Usage

1. Connect the wheel to the air compressor

2. Use the cover piece to ﬁx the wheel

3. Cover the wheel with the red cover

4. Fix the foot to the air compressor

5. Remove the warning sign and the oil ﬁller plug

6. Screw the red breather assembly into the hole at the top of the compressor head

7. Fix the air ﬁlter to the right side of the compressor head

www.hoses.co.uk

1. The air compressor should be placed in a clean, dry and ventilated area

2. In order to extend the compressor lifespan, reduce the heat of moving parts by making sure the

air compressor cover is at least 0.3 - 0.5 metres away from the wall

3. Keep the voltage within ±5% of rating

4. Keep the oil level within the indicator

5. Recommended compressor oil AC2100 or AC2032

6. The normal working temperature should be -5°C - +35°C

7. The normal working temperature of the air compressor is 180°C and lubricating oil

in the crankcase is 70°C

8. Open the outlet valve and let the air compressor run for 10 minutes without load before operation

Preparation for Usage

Safety Guidelines

DANGER

1. TO REDUCE THE RISK OF FIRE OR EXPLOSION, NEVER SPRAY FLAMMABLE

LIQUIDS IN A CONFINED AREA. It is normal for the motor and pressure switch to produce

sparks while operating. If sparks come into contact with vapours from gasoline or other

solvents, it may ignite ﬁre or an explosion. The air compressor must be stored and operated

in a well-ventilated area. Do not smoke while using the air compressor, and keep away from

ﬂammable material.

When Trichloroethane and Methylene Chloride come into contact with aluminium in painting

equipment, it can produce a chemical reaction which may cause an explosion. If you are using

these solvents, please use only stainless steel spray equipment.

3. Never directly inhale the compressed air produced by a compressor.

Direct Driven Compressor Operation Manual Model No. SACDD-24/50

www.hoses.co.uk

www.synairgy-eu.com

WARNING

1. Do not weld onto the air tank of this compressor. Welding on the air compressor tank will cause a

safety hazard and will void the product warranty

2. Never use an electric air compressor outdoors or on a wet surface; it may cause an electric shock

3. Please power off the air compressor when not in use

4. Check the manufacturer’s maximum pressure rating for air tools and accessories.

The compressor outlet pressure must be regulated so as not to exceed the maximum pressure

rating for the tools

5. High temperatures and moving parts are present under the outer cover. To prevent burns or

other injuries, DO NOT operate with the outer cover removed. Allow the compressor parts to cool

before handling or servicing

6. Ensure you read all labels when you are spraying paints or toxic materials; follow the safety

instructions provided, and use a respirator mask

7. Always wear safety goggles or glasses when using an air compressor. Never point any nozzle or

sprayer towards a person or any part of the body

8. Do not adjust the pressure switch or regulating valve for any reason; they have been pre-set at the

factory for the maximum pressure for this unit

CAUTION:

1. Drain the moisture from the tank on a daily basis. A clean, dry tank will help prevent corrosion

2. Pull off the pressure relief valve ring daily to ensure that the valve is functioning properly, and to

clear any obstructions

3. To provide adequate ventilation for cooling, the compressor must be kept a minimum of 0.3-0.5

metres from the nearest wall, in a well-ventilated area

4. Fasten the compressor down securely, and release the pressure from the tank before

transportation

5. Protect the air hose and electrical wire from damage and punctures. Inspect them weekly for

weak or worn spots, and replace them if necessary

Safety Guidelines

www.hoses.co.uk

This range of Synairgy oil lubricated compressors are built with performance and reliability in mind,

with a robust strong design for trade and DIY applications. The compressors have the advantage

of a compact construction and lightweight design. Easy operation, excellent safety characteristics

and low noise levels make it perfect for all typical applications, including; paint spraying, inﬂating,

blowing, nailing, air tools and other applications where compressed air is required.

1. Pull the cover off and connect the breather pipe and air ﬁlter before running the compressor

2. Never unscrew any connecting parts when the tank is pressurised

3. Disconnect the plug before disassembling any electrical part

4. Never adjust the safety relief valve

5. Never use the compressor when the voltage is too low or too high

6. Never use electrical wire more than 5m long

7. Never disconnect the plug to stop the compressor; turn the switch to off instead

8. If the outlet valve doesn’t work, search for the cause immediately so as not to damage the motor

9. Lubricating oil must be clean; oil level should be kept within the indicator

10. Before opening the outlet valve ensure the compressor is switched off and the plug is

disconnected from the power supply

11. The maximum decibel level or the compressor is 87dB

Caution

Brief Description

Direct Driven Compressor Operation Manual Model No. SACDD-24/50

www.hoses.co.uk

www.synairgy-eu.com

Code

Voltage Power Cylinder Rated

Speed Capacity Pressure Tank N.W

V/Hz KW hp mm*n rpm l/min C.F.M bar/psi L Usgal kg

SACDD-24 220/50 1.5 2 47*1 2850 198 7 8/115 24 6.34 23.5

SACDD-50 220/50 1.5 2 47*1 2850 198 7 8/115 50 13.21 32

Compressor Overview

Technical Speciﬁcation

1. Plastic cover

2. Pressure switch

3. Regulating valve

4. Outlet valve

5. Pressure gauge

6. Check valve

7. Drain cock

8. Wheel

9. Discharge pipe

10. Air tank

11. Crankcase

12. Safety relief valve

www.hoses.co.uk

Parts List

Direct Driven Compressor Operation Manual Model No. SACDD-24/50

www.hoses.co.uk

www.synairgy-eu.com www.synairgy-eu.com

No. Designation Qty No. Designation Qty

1 Bolt M6×40 4 35 Rotator 1

2 Washer 4 36 Back bearing 6204 1

3 Connector 1 37 Stator 1

4 Cylinder head 1 38 Capacitor 1

5 Air ﬁlter 1 39 Screw M8 1

6 Cylinder head gakset 1 40 Screw M10 2

7 Valve cock 1 41 Circlip 2

8 Valve plate 1 42 Screw washer 4

9Air intake valve 1 43 Screw M5 x 100 4

10 Valve plate gasket 1 44 Fan 1

11 Cylinder 1 45 Motor cover 1

12 Cylinder gasket 1 46 Wave gasket 1

13 Screw 2 47 Snap ring Φ14 1

14 Pressure gauge 40mm dia 1 48 Fan cover 1

15 Piston ring 2 49 Screw M5*14 10

16 Oil ring 1 50 Air tank 1

17 Piston 1 51 Rubber feet 1

18 Piston pin 1 52 Connector 1

19 Piston pin circlip 2 53 Spring washer 2

20 Connecting rod 1 54 Pressure swtich 1

21 Screw 1 55 Safety relief 1

22 Crank 1 56 Pressure gauge 50mm dia 1

23 Discharge pipe connector 2 57 Check valve 1

24 Wheel screw 2 58 Water release valve 1

25 Discharge pipe 1 59 Wheel 2

26 Oil leveler 1 60 Axle sleeve 2

27 Oil leveler gasket 1 61 Wheel axle 2

28 Crank case front cover 1 62 Release pipe connector 1

29 Screw M6 6 4 63 Release pipe 1

30 Breather pipe 1 64 Motor wire 1

31 Crank case rubber gasket 65 Wire contact

32 Oil seal 66 Outlet valve

33 Crank case 67 Power cable

34 Front bearing 6202 68 Handle sleeve

Parts List

www.hoses.co.uk

1. Open the drain cock under the tank and then close it

2. The compressor is controlled by the pressure switch. It can be stopped automatically as

pressure increases to the maximum and restarted as pressure decrease to the minimum.

The rated pressure has been set during production; do not adjust needlessly. As soon as the

motor is switched off the compressed air in the discharge pipe should be released through

the outlet valve under the switch, this is required for restarting, or the motor will be damaged

The rated pressure can be adjusted by turning

the adjusting bolt of the switch

3. The outlet pressure of compressed air can be

adjusted, by the regulating valve (Fig.3). Pull

up the knob of the regulation valve and turn it

clockwise to increase the pressure

4. When the compressor needs to be stopped,

set the switch to the off position

1. Clean the crankcase and replace the lubricating oil after the ﬁrst 10 working hours

2. Clean the oil level after every 20 working hours, and replenish it if necessary

3. Open the drain cock under the tank to exhaust condensation after every 60 working hours

4. Clean the crankcase every 120 working hours and renew the oil, clean the air ﬁlter, check the

safety valve and pressure gauge

(Fig.3)

Operation and Adjustment

Maintenance

Direct Driven Compressor Operation Manual Model No. SACDD-24/50

Safety relief valve

Outlet port

Air gauge Regulator

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Synairgy Luftkompressor Handbücher

Synairgy

Synairgy SACBD-100 Bedienungsanleitung

Beliebte Luftkompressor Handbücher anderer Marken

Sparmax

Sparmax DC-25XR Bedienungsanleitung

KAESER

KAESER M122 Bedienungsanleitung

GMC

GMC GAC1500 Bedienungsanleitung

Briggs & Stratton

Briggs & Stratton Air Compressor Bedienungsanleitung

Fini

Fini F3GST2TK Bedienungsanleitung

Industrial Air

Industrial Air CP1580325 Programmierhandbuch

Campbell Hausfeld

Campbell Hausfeld RP3300 Kurzanleitung

Ingersoll-Rand

Ingersoll-Rand UP6 20 HP Bedienungsanleitung

Hitachi

Hitachi EC99S Bedienerhandbuch

Parkside

Parkside PKO 270 A1 Bedienungsanleitung

Sullair

Sullair 185 Bedienungsanleitung

Clas Ohlson

Clas Ohlson QIE-ZTH-15 Bedienungsanleitung

Ferm

Ferm CRM1046 Bedienungsanleitung

BE AC153 Bedienungsanleitung

RIDGID

RIDGID OF25150A Bedienungsanleitung

Johnson Controls

Johnson Controls QUANTUM LX Handbuch

Sears

Sears Craftsman 919.167463 Bedienungsanleitung

Ring Automotive

Ring Automotive RAC700 Bedienungsanleitung