Synology UC3200 Handbuch
Synology Unied Controller UC3200
Hardware Installation Guide
Table of Contents
Chapter 1: Before You Start
Package Contents 3
Synology UC3200 at a Glance 4
Safety Instructions 6
Hardware Specication 7
Optional Accessories 8
Chapter 2: Hardware Setup
Tools and Parts for Component Installation 10
Install Drives 10
Install Memory Modules 12
Install PCle Add-in Cards 15
Install and Remove Rail Kits 16
Expansion Unit Deployment and Topology 18
Start up Your Synology UC3200 20
LED Indicator Table 21
Chapter 3: System Maintenance
Replace System Fan 23
Replace Power Supply Unit (PSU) 24
Initial Troubleshooting Guide 24
Chapter 4: Initialize DSM UC on Synology UC3200
Initialize DSM UC with Web Assistant 25
Learn More 25
Synology_HIG_UC3200_20190411
2
Synology Unied Controller UC3200 is an enterprise server consisting of both system hardware and the software
operating system, DSM UC. This manual will guide you through all conguration aspects of your UC3200,
including the hardware components, setup procedures, system maintenance, and initial troubleshooting
instructions.
Note: All images below are for illustrative purposes only, and may dier from the actual product.
Package Contents
Main unit x 1 AC power cord x 2
Screws for 2.5” drives x 52
Screws for 3.5” drives x 52
Before You Start 1
Chapter
3
3
4Chapter 1: Before You Start
Synology UC3200 at a Glance
No. Article Name Location Description
1Power Button and Indicator
Front
1. Press to power on your Synology Unied Controller.
2. To power o the Synology Unied Controller, press and hold until you
hear a beep sound and the Power LED starts blinking.
2HA Status Indicator Displays the status of the HA (High Availability). For more information, see
"LED Indicator Table."
3Alert Indicator Displays warnings regarding fan or temperature. For more information,
see "LED Indicator Table."
4Beep O Button Press to deactivate the beeping sound that is emitted when a malfunction
occurs.
5Drive Status Indicator Displays the status of drives. For more information, see "LED Indicator
Table."
6 Drive Tray Install drives (hard disk drives or solid state drives) here.
7 Rail Kit Release Tab Push in and hold to release the Synology Unied Controller from the rail
kit lock.1
1For more information about the rail kit installation, please refer to the Quick Installation Guide that comes with the rail kit.
5Chapter 1: Before You Start
No. Article Name Location Description
8 Power Port
Back
Connect power cords here.
9 PSU Indicator and Beep O
Button
1. Displays the status of the power supply unit (PSU). For more
information, see "LED Indicator Table."
2. Press to deactivate the beeping sound that is emitted when a
malfunction occurs.
10 PSU Fan Disposes of excess heat and cools the PSU.
11 Console Port This port is used for manufacturing use only.
12 PCI Express Expansion Slot Supports additional PCIe network interface cards.
13 SAS OUT Port Connect to Synology Expansion Unit2here.
14 1GbE LAN Port Connect RJ-45 network cables here.
15 10GBase-T LAN Port Connect RJ-45 network cables here.
16 RESET Button
1. Press and hold until you hear a beep sound to restore the default IP
address, DNS server, and password for the admin account.
2. Press and hold until you hear a beep sound, then press and hold
again until you hear three beep sounds to return the Synology Unied
Controller to “Ready” status so that DSM UC can be initialized.
17 Power Indicator Displays the status of the power supply of the controller. For more
information, see "LED Indicator Table."
18 Status Indicator Displays the status of the controller. For more information, see "LED
Indicator Table."
19 Alert Indicator Displays warnings regarding fan or temperature of the controller. For
more information, see "LED Indicator Table."
20 Remove Indicator Displays the status indicating whether the controller is removable. For
more information, see "LED Indicator Table."
2For more information about Synology Expansion Unit supported by your Synology Unied Controller, please visit www.synology.com.
6Chapter 1: Before You Start
Safety Instructions
Keep away from direct sunlight and away from chemicals. Make sure the environment does not
experience abrupt changes in temperature or humidity.
Place the product right side up at all times.
Do not place near any liquids.
Before cleaning, unplug the power cord. Wipe with damp paper towels. Do not use chemical or
aerosol cleaners.
To prevent the unit from falling over, do not place on carts or any unstable surfaces.
The power cord must plug in to the correct supply voltage. Make sure that the supplied AC voltage is
correct and stable.
To remove all electrical current from the device, ensure that all power cords are disconnected from
the power source.
Risk of explosion if battery is replaced with an incorrect type. Dispose of used batteries appropriately.
CAUTION: Restricted Access Location
This server is intended for installation only in restricted access locations as dened where both these conditions
apply:
• Access is through the use of a lock or tool and key, or other means of security, and is controlled by the
authority responsible for the location.
• Access can only be gained by service persons or by users who have been instructed about the reasons for
the restrictions applied to the location and about any precautions that shall be taken.
7Chapter 1: Before You Start
Hardware Specication
Item UC3200
Compatible Drive Type 3.5” / 2.5” SAS x 12
Maximum Raw Capacity • 192TB (12 x 16TB HDD)
• 576 TB with 2 x RXD1219sas (Expansion unit)
External Device Port SAS OUT x 1 (Per controller)
LAN Port • 1GbE (RJ-45) x 2 (Per controller)
• 10GBase-T (RJ-45) x 1 (Per controller)
PCIe Slot Gen3 x8 slots (x8 link) x 1 (Per controller)
Size (H x W x D) (mm) • 88 x 482 x 724 (Including rack mount kits)
• 88 x 430.5 x 692 (Not including rack mount kits)
Weight (kg) 19.7
Supported Client
• Windows Server 2008 onward
• VMware 5 onward
• Solaris 10 onward
• Citrix XenServer 7.2 onward
• SUSE Linux ES 11 onward
• Red Hat ES 6.10 onward
File System Internal: Btrfs
Supported RAID Type • Basic • JBOD • RAID 0 • RAID 1
• RAID 5 • RAID 6 • RAID 10 • Synology RAID F1
Agency Certication • FCC Class A • CE Class A • BSMI Class A
• EAC • VCCI • CCC • RCM
HDD Hibernation N/A
Scheduled Power On/O N/A
Wake on LAN N/A
Language Localization
Environment Requirement
• Line voltage: 100V to 240V AC
• Frequency: 50 to 60Hz
• Operating Temperature: 32 to 95˚F (0 to 35˚C)
• Storage Temperature: -5 to 140˚F (-20 to 60˚C)
• Relative Humidity: 5% to 95% RH
Note: Model specications are subject to change without notice. Please refer to www.synology.com for the latest information.
8Chapter 1: Before You Start
Optional Accessories
With Synology accessories, you can customize your Synology Unied Controller to t dierent business
environments without worrying about compatibility and stability. Visit www.synology.com/compatibility for more
information.
• Memory Module
Model Name Picture Description
D4EC-2666-8G 8GB D4EC-2666 ECC U-DIMM
D4EC-2400-16G 16GB D4EC-2400 ECC U-DIMM
• PCIe Add-in Card
Model Name Picture Description
E10G18-T2 Dual-port, 10GbE RJ-45
Network Interface Card
E10G18-T1 Single-port, 10GbE RJ-45
Network Interface Card
E10G17-F2 Dual-port, 10GbE SFP+
Network Interface Card
9Chapter 1: Before You Start
• Expansion Unit
Model Name Picture Description
RXD1219sas
12-bay Rackmount type
expansion unit, compatible with
3.5”/2.5” SAS drives, up to 2
units connections
• Rail Kit
Model Name Picture Description
RKS1317 Sliding rails
• Spare Part
Model Name Picture Description
Disk Tray (Type R7) 3.5"/2.5" Drive Tray
FAN 60*60*51_2 System Fan Module
PSU 500W-RP
Module_2 Redundant PSU Module
PSU 500W-RP SET_2 Redundant PSU Set (Cage x 1, PSU
Module x 2)
Tools and Parts for Component Installation
Please prepare tools and parts below before setting up your Synology Unied Controller:
• A screwdriver.
• At least one 3.5” or 2.5” SAS drive (please visit www.synology.com/compatibility for compatible drive
models).
Warning: If you install a drive that contains data, the system will format the drive and erase all existing data. Please
back up any important data before installation.
• Rail mounting kit. (please see the Optional Accessories section to nd out the suitable rail kit for cabinet
installation)
Warning: We suggest mounting your Synology Unied Controller on a cabinet before installing any drives since the
heavy weight will increase the installation diculty.
Install Drives
Please follow steps below for drive installation:
1 Open the drive tray:
a Find the small button located on the left side of the drive tray handle. Press the button down, and the drive
tray handle will pop out.
b Pull the drive tray handle out as illustrated below.
2 Install drives:
• For 3.5” drives: Place the drive in the drive tray. Turn the tray upside down and tighten screws into the four
spots indicated below to secure the drive.
Hardware Setup
10
2
Chapter
Inhaltsverzeichnis
Andere Synology Controller Handbücher
