Synrad Firestar f201 Bedienungsanleitung
1 QSG f201 version 2.1
Firestar™ f201 laser & Flyer 3D System Quick Start Guide
a Novanta company
a Novanta company
1. Lift the Flyer 3D Marking Head out of the box only by the middle; do not use housing, coolant ttings,
or anything else on the sides to lift the laser.
Important
Note:
See the Flyer 3D Marking Head and Firestar f201 Laser Operators Manual for complete
installation details and instructions. A PDF version is available Online at:
http://www.synrad.com/Manuals/manuals_laser.htm.
Marking Head Unpacking:
Attention: For complete details, refer to the Getting Started (System Inventory and Mounting)
Sections in the Firestar f201 and Flyer 3D Marking Head Operator’s Manual.
Read all Danger, Warning, Caution terms, symbols, and instructions located in the (Laser Safety
Hazard information) sections in the Flyer 3D Marking Head and Firestar f201 Laser Operation Manuals.
Caution
Correct
1.1 Lifting the Marking Head correctly by holding in the middle.
1.2 Avoid mis-alignment risk! Do not use housing tting or fan (as shown) or any thing on
the side to lift.
2 QSG f201 version 2.1
Firestar™ f201 laser & Flyer 3D System Quick Start Guide
a Novanta company
a Novanta company
2. Locate the shipping components for the Marking Head at the bottom of the box under the Marking
Head.
2.1 Remove the marking head from the box.
2.2 Retrieve the components from the bottom
of the box.
3.1 Remove and retain the marking head foam.
3. Don’t forget to save all shipping container(s) and inserts for use when shipping or relocating either
the laser or the marking head to another location. Packaging is specially designed to protect your laser.
3 QSG f201 version 2.1
Firestar™ f201 laser & Flyer 3D System Quick Start Guide
a Novanta company
a Novanta company
Laser Unpacking:
Important
Note:
Caution! Packing the laser incorrectly can damage the laser!
Keep All Foam and Packaging, you will need to re-use it when moving your
laser. Refer to this guide and the Getting Started/Technical Reference chap-
ters in the laser’s Operation Manual when re-packaging for shipping and/or
relocation.
4.1 Locate the wire harness inside the end cap.
4.2. When re-boxing, note the xture side faces
the end cap.
Caution! When packing the laser for relocation or shipment, nothing can be on the sides
of the laser at any time as damage will occur. The skin on the sides of the laser is fragile!
All box components must be stowed under the laser.
The ttings will be damaged in shipping if not re-packaged as shown above.
4. Locate the mounting hardware kit at the end cap (tting side of the box or the cardboard pocket.)
5. Two people will be required to lift the laser out of the box using the lifting handles on each side of
the box.
Laser ttings
5.2 Two places for both people at
opposite ends of the box for lifting.
5.1 Correct hand placement for
lifting the laser out of the box.
4 QSG f201 version 2.1
Firestar™ f201 laser & Flyer 3D System Quick Start Guide
a Novanta company
a Novanta company
Mounting (preparing the rail):
Note notch
location.
6.2 Four (4) eye bolt locations on the rail
and associated hardware.
6. Remove the rail & hardware from the packaging. Ensure the notch is facing down and to the left.
Assemble the eye bolts rst, the bar second, then the triangle bars third.
Eye bolts
6.3 Ax the bolt onto the eye bolt as shown.
6.4 Assemble the 4 eye-bolts/nuts onto
the rail as shown above in 6.2.
Triangle
bars
Bar
6.1 Rail Kit.
6.5 Tighten the eye bolt to the rail.
6.7 Assure the bolt is snugged ush
with the rail as shown above.
6.6 Detach the bolt on the eye-bolt
so that it moves down toward the rail.
5 QSG f201 version 2.1
Firestar™ f201 laser & Flyer 3D System Quick Start Guide
a Novanta company
a Novanta company
7.2 Place the bar on the rail aligning the
pegs as shown.
7.3 Attach the bar securely to the rail with
the four (4) bar hardware screws shown in
7.1.
7. Place the bar onto the rail as shown below.
Bar
(4) Bar
screws
7.1 Bar and hardware.
8. Install the triangle bars as shown below.
Note: The Laser feet screws are shown in their nal locations for clarity on the rail above.
8.1 The Triangle bar screws and nal placement on the rail are shown circled in red below.
Laser feet
screws
Laser feet
screws
Two (2) Bar/
Triangle bar
end screws
Attention: When attaching the Marking Head to the Laser, make sure the notch is as shown in
gure below before going on to the next step.
Mounting (Continued):
6 QSG f201 version 2.1
Firestar™ f201 laser & Flyer 3D System Quick Start Guide
a Novanta company
a Novanta company
9. After the triangle bars are installed place the side screw(s) as shown below on each side.
9.1 Install the two (2) bar/triangle bar end screws, axing the triangle rails to the bar rail, see 7.1
on the previous page.
7 QSG f201 version 2.1
Firestar™ f201 laser & Flyer 3D System Quick Start Guide
a Novanta company
a Novanta company
10. The laser should arrive with feet and shims installed, please refer to the gure below for further detail.
11. Locate the marking head Mounting Hardware Kit ( ) Marking Head Safety tube,
clamp, and Allen screws.
Mounting (the laser and the marking head to the rail):
Should look like this when done.
Note: Very important! Assure the notch
is facing to the back left of the laser!
Otherwise, re-work required because the
head will be mounted incorrectly. Notch
8 QSG f201 version 2.1
Firestar™ f201 laser & Flyer 3D System Quick Start Guide
a Novanta company
a Novanta company
12. Before mounting the laser to the rail, ensure the aperture seal is removed.
AVOID EXPOSURE
Invisible laser radiation
is emitted from
this aperture.
8
9
6
5
4
INTERFACE
LASE
RDY
PWR
AB
7
SA Model Shown
Attention:
12.3 Mount the marking head to the rail. Tighten all four (4) screws, (two on each side.)
12.1 Remove the
aperture seal.
12.2 Place the laser onto the rail with the rear left facing the notch as
shown. Tighten each of the three (3) screws on all four (4) mounting
feet.
Remove the laser aperture self-adhesive lm before mounting to
the rail. Don’t tighten the Allen screws on the clamp until the laser is
mounted to the rail.
Mounting (the Laser and the Marking Head to the rail):
9 QSG f201 version 2.1
Firestar™ f201 laser & Flyer 3D System Quick Start Guide
a Novanta company
a Novanta company
13. Assure the Laser and Marking Head are mounted on the rail rst, then assemble the tube’s path
enclosure below. Locate the path enclosure components in the kit.
13.3 Place the expander cooling head into the path enclosure tube
on the gasket end.
13.1 Locate the components above.
13.2 Place the gasket in the path
enclosure tube.
Gasket
Path
Enclosure
Tube
Expander
Cooling Head
13.4 Apply mild compression to the assembly and slide into place.
Rotate the
cooling head
down
10 QSG f201 version 2.1
Firestar™ f201 laser & Flyer 3D System Quick Start Guide
a Novanta company
a Novanta company
14. Marking Head & f201 series laser mounted on rail.
14.1 Should look like this.
Andere Handbücher für Firestar f201
1
Inhaltsverzeichnis
