SYKD2N-H5/L5 Specification SYKD2N-H5/L5 Operation Manual
SYKD2N-H5/L5 Operation Manual
＊
Card Frequency H5：13.56MHz(Multi-Format)
L5：125KHz(EM)
Keypad 13 Keypad(Capacitive)
Active RFID Support 2.45GHz active RFID(option)
Interface RS485 and Wiegand(26/32/34/35/37/42/66 Bit)
Ethernet / Wi-Fi
Ethernet 10M/100M Ethernet Port
Wi-Fi 802.11 b/g/n
Baud Rate 19,200 bps(4,800~230,400bps)
Capacity of Records 2000
Capacity of Cards 2000
Status Indicator LED (RGB)
IR Sensor 1 IR sensor for waving hand.
Digital Input Up to 3 (1 for non-voltage DI+2 for non-voltage DI share same port
with Wiegand)
Digital output Up to 2 (2 Relay output)
Holiday Control 30 Day
Anti-duress PIN 4Set
Anti-Tamper
/Anti-Lockup Build-in(Infrared) / (Watchdog)
Voice output Build-in Buzzer
Operating
temperature -10℃~+60℃
Input Voltage 8V ~ 28V DC / 1W ~ 6W
Dimension(W x H x D) 90(W) x 124(H) x 27(D) mm
Enter #+#+0+1 (Beep) +【Password】+#
Note: Default Password:1234；Auto-logout after user login for 30
seconds and without doing any setting.
Please login device first before doing the following setup
Enter #+#+0+2 (Beep) +【ID】+#
Note: ID Range is 1~9999；(Default ID：1)
Enter #+#+0+3 (Beep) +【YYYYMMDDhhnnss】
+#
Note: For example, 2011/01/29 03:25:23,pleaseenter
20110129032523
Enter #+#+0+4 (Beep) +【New Password】+#
Note: Login password is 4 char (Default: 1234)；user can setup
factory default via computer software if user forgot the password.
Enter #+#+0+5 (Beep) +【Time】+#
Note: Time range is 0~250 seconds；0 means always on(Default:30
Seconds)
Enter #+#+0+6 (Beep) +【S】+#
Note: Show Card Mode 0：None、1：Card No(Default)、2：UID、3：
Char
Enter #+#+0+7 (Beep) +【Language】+#
Note: 0：ENGLISH(Default)、1：CHT、2：CHS
Enter #+#+0+8 (Beep) +【Encode】+#
Note: 0：UNICODE(Default)、1：BIG5、2：GB2312
Enter #+#+0+9 (Beep) +【Class】+#
Note: 0：Disable(Default)、1：Enable
Switch shift mode needs to operate under shift setting mode
enabled：
On Duty：#+【1】(Beep)；Off Duty：#+【2】(Beep)
Go Out：#+【3】(Beep)；Return：#+【4】(Beep)
Start Overtime：#+【5】(Beep)；Finish Overtime：#+【6】(Beep)
A. Enter #+#+1+1(Beep)+【Card Number】+#
+Show Card+ ＊
B. Enter #+#+1+1(Beep)+Show Card + ＊
Note:
A.User can define specific card number (number from 1 to 2000).
B.System will assign card number automatically.
A.Enter #+#+1+2(Beep)+【Card Number】+#
B.Enter #+#+1+2(Beep)+Show Card + ＊
Note:
A.User can define specific card number (number from 1 to 2000).
B.System will erase the showing card.
Enter #+#+1+3(Beep)+【Password】+#+
Show Card + ＊
Note: Showing card that will be created password ；Password
contains 1 ~ 4 numeric code(After enabled card password function，
it needs to work with door open mode)
Enter #+#+1+5 (Beep) +【M】+#+Show
Card+ ＊
Note: Enter master card number(card number is 1~3) then show
the card to device. (To login,user can use PIN code or master card
after pressing ##01)
Enter #+#+1+9 (Beep) +【Password】+#
Note: Login device before doing the procedure(Default Login
Password:1234 )
Enter #+#+2+1 (Beep) +【Time】+#
Note: Time range to open door is 0~255 second；0meansmodefor
open one time close one time.
Note Press to return the previous steps while doing：
error input. Fast procedures to setup for access door by
using card or password.
A: ##01 Login
B. ##11 Add one card *
C. ##13 Setup password for this card *
D. ##23 →0 Switch access door with PIN only #
E. ##22 →1 Switch access mode as card or pin to access door #
F. Reboot
