System air Topvex SC Fehlerbehebungshandbuch

Document in original language | 162528 · A001

Air Handling Unit

Topvex SC, TC

Operation and Maintenance Instructions GB

162528 | A001

E&OE

Systemair AB reserves the rights to alter their products without notice.

This also applies to products already ordered, as long as it does not affect the previously agreed specifications.

162528 | A001

Contents

1 Overview ......................................................1

1.1 Intended use .........................................1

1.2 Disclaimer ............................................1

1.3 Warranty..............................................1

1.4 EU Declaration of Conformity ....................2

2 Warnings.......................................................3

3 Product description..........................................3

3.1 Internal components ...............................3

4 Duct connections.............................................7

4.1 Topvex SC.............................................7

4.2 Topvex TC.............................................8

5 Access control cabinet......................................9

6 Maintenance ...... ............. ........... ........... ....... 10

6.1 Maintenance intervals ........................... 10

6.2 How to replace supply/extract air

filter..................................................11

6.3 How to clean the heat exchanger............. 11

6.4 How to clean the fans ........................... 12

6.5 How to clean hot water heating

battery ..............................................12

6.6 How to clean the electrical heating

battery ..............................................13

6.7 Where to reset tripped fuses................... 13

6.8 How to reset the manual overheat

protection (EL units).............................. 14

6.9 How to replace the fan module................ 15

6.10 How to replace the heat

exchanger .......................................... 15

6.11 How to change the internal battery in

CU27–C..............................................20

6.12 How to clean the extract air louvres and

inlet diffusers ...................................... 20

6.13 Clean the outdoor air intake.................... 20

6.14 How to clean the duct system ................. 20

7 Troubleshooting............................................ 21

8 Alarms........................................................22

8.1 Alarm list............................................ 22

9 Service .......................................................23

10 General conditions......................................... 23

10.1 Standard tools .................................... 23

10.2 Reference documentation ...................... 23

11 Spare parts .................................................. 23

Overview |1

1 Overview

This manual includes the information required for operating and maintaining the heat recovery unit. If other accessories

not included at delivery are in use, read their separate instructions.

1.1 Intended use

The units are intended to provide ventilation and depending on settings, heat recovery, air heating or free cooling.

1.2 Disclaimer

The manufacturer may not be held liable for any damage to people or property caused by improper installation, start-

up and/or improper use of the unit and/or failure to implement the procedures and instructions included in this manual.

1.3 Warranty

General conditions are applied if purchase contract not state otherwise.

These units are delivered complete, tested and ready for being operated. Any form of warranty will become null and

void in the event that the unit is modified without manufacturer’s authorisation. Carry out all the planned maintenance

according to this manual in a timely and proper way.

Wear parts are not covered by the warranty.

162528 | A001

2|Overview

1.4 EU Declaration of Conformity

Manufacturer

Systemair Sverige AB

Industrivägen 3

SE-739 30 Skinnskatteberg Sweden

Phone: +46 222 440 00

www.systemair.com

The manufacturer hereby confirms that Topvex SC, TC

comply with all applicable requirements in the following

directives and regulations.

Machinery Directive 2006/42/EC

Ecodesign Directive 2009/125/EC

327/2011 Requirements for fans

1253/2014 Requirements for ventilation units

Low Voltage Directive 2014/35/EU

EMC Directive 2014/30/EU

The following harmonized standards are applied in ap-

plicable parts:

EN ISO 12100

Safety of machinery - General principles for design - Risk

assessment and risk reduction.

EN 13857

Safety of machinery – Safety distances to prevent hazard

zones being reached by upper or lower limbs.

EN 60204-1

Safety of machinery – Electrical equipment of machines –

Part 1: General requirements.

EN 60335-1

Household and similar electrical appliances – Safety Part

1: General requirements.

EN 60335-2-40

Safety of household and similar electrical appliances -

Part 2-40: Particular requirements for electrical heat

pumps, air-conditioners and dehumidifiers.

EN 50106

Safety of household and similar appliances – Particular

rules for routine tests referring to appliances under the

scope of EN 60 335-1.

EN 60529

Degrees of protection provided by enclosures (IP Code).

EN 62233

Measurement methods for electromagnetic fields of

household appliances and similar apparatus with regard

to human exposure.

EN 61000-6-2

Electromagnetic compatibility (EMC) – Part 6-2: Generic

standards – Immunity for industrial environments.

EN 61000-6-3

Electromagnetic compatibility (EMC) – Part 6-3: Generic

standards – Emission standards for residential, commer-

cial and light-industrial environments.

EN 13053

Ventilation for buildings – Air handling units – Rating and

performance for units, components and sections.

The declaration applies only to product in the condition it

was delivered in and installed in the facility in accordance

with the included installation instructions. The insurance

does not cover components that are added or actions

carried out subsequently on the product.

The complete technical documentation is available.

Skinnskatteberg, 2020–05–11

Sofia Rask

Managing Director

162528 | A001

Warnings |3

2 Warnings

The following admonitions will be presented in the different sections of the document:

Danger

• Indicates a potentially or imminently hazardous situation which, if not avoided, could result in death or

serious injury.

Warning

• Indicates a potentially hazardous situation that may result in minor or moderate injuries.

Caution

• Indicates a risk of damaging the product or prevent optimal operation.

Important

• This appliance can be used by children aged from 8 years and above and persons with reduced physical,

sensory or mental capabilities or lack of experience and knowledge if they have been given supervision

or instruction concerning use of the appliance in a safe way and understand the hazards involved.

• Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children

without supervision.

3 Product description

3.1 Internal components

3.1.1 Supply and extract air fans

The fans have external rotor motors of EC type which are steplessly controlled individually by setting the control signal

to a fixed value. It is possible to program the speed in 3 steps (high/normal/low) depending on the programming of the

week schedule. The motor bearings are life time lubricated and maintenance free. It is possible to remove the fans for

cleaning, see chapter 6 for more information.

3.1.2 Pressure transmitter fans/filters

Two pressure transmitters are installed, each of the sensors has two functions. One function is to measure the differen-

tial pressure over the inlet cone of the fan impellers to maintain the airflow at constant level (CAV function as standard).

The other function, is to measure the differential pressure over the supply and extract air filters. When the pressure

drop reaches the set value, an alarm is triggered in the main regulator, which indicates that the filter needs to be

replaced.

3.1.3 Supply and extract air filters

The filters are of bag filter type with filter quality ePM1 60% (F7) for the supply air filter and ePM10 60% (M5) for the

extract air filter. The filters need to be replaced when polluted. New sets of filters can be acquired from your installer or

wholesaler.

162528 | A001

4| Product description

3.1.4 Heat exchanger

Topvex SC, TC models are equipped with a counter flow heat exchanger and a by-pass damper. The operation of the

by-pass damper is automatic and depends on the set temperature or if defrosting is in operation.

For defrosting a pressure transmitter is installed which measure the differential pressure over the heat exchanger.

3.1.5 Temperature sensor

4 temperature sensors (PT1000) are included in the unit from factory. The sensors are as follows:

• Supply air sensor

• Extract air temperature sensor

• Outdoor air temperature sensor

• Exhaust air temperature sensor

• Efficiency temperature sensor

The supply air sensor is loosely delivered with the unit and needs to be installed in the supply air duct externally from

the unit. See Installation instructions for more information.

3.1.6 Water heating battery

In units with built in water heating battery the hot water coil is located next to the supply air connection. The hot water

coil can be either HWL (hot water coil, low power) or HWH (hot water coil, high power). The coil material is copper pip-

ing with a frame of galvanized sheet steel and aluminium fins. The coil is equipped with venting and immersion sensor

for frost protection.

3.1.7 Electrical heater

In units with built in electrical heater the heating rods are located after the supply air fan in the airflow direction. The

material is stainless steel. The electrical heating battery has both automatic and manual overheating protection. The

manual overheat protection is reset by pushing the red button on top of the electrical heater frame (figure 3). The elec-

trical heater is mechanically interlocked by an air flow sensor in the supply air. The power demand of the electric heat-

ing coil is controlled by the main regulator, which controls the heat steplessly by a TTC triac control according to the

selected control function that is set in the control panel.

162528 | A001

Product description | 5

3.1.8 Free cooling description

This function is used during the warm period to save energy by using cold outdoor air, e.g. during night time, to cool

down the building and thereby reducing the need for cooling during the day time.

Note:

The following is only valid if the free cooling function is activated in the program menu.

Free cooling is only activated when the following starting conditions are met.

Starting conditions:

• Less than 4 days have passed since the unit was last in running mode

• The outdoor temperature during the previous running period exceeded a set limit (+22°C)

• It is between 00:00 and 07:00:00 in the day (settable)

• The timer outputs for normal speed, Extended running normal and External stop are Off

• A time channel will be On sometime during the recently started 24 hours.

The unit checks the night temperature (indoor and outdoor temperature) during 3 minutes at the set starting hour when

the fans are started so that the sensors can perform a temperature measurement. If above conditions are met the free

cooling function is started, if not the unit goes back to OFF position.

If the outdoor sensor is not located in the outdoor air inlet duct and a room sensor has been selected, the unit will not

start free cooling as long as all the temperatures are not within the start and stop temperature intervals.

Stop conditions:

• Outdoor temp above the set max value (+18°C) or below the set min value (condensation risk, +10°C)

• The room temp/extract air temp is below the set stop value (+18°C)

• One of the timer outputs for normal speed, External stop or Extended running normal is On

• The time has past 07:00:00.

If any stop conditions is fulfilled after three minutes, the unit will stop again. Otherwise, operation will continue until a

stop condition is fulfilled.

When free cooling is active, the fans run at normal speed or the set value for pressure/flow control and the digital out-

put free cooling is active. The outputs block heating, cooling and heat exchanger. After free cooling has been activated,

the heating output is blocked for 60 minutes (configurable time). When using free cooling, an offset to normal fan con-

trol setpoint is adjustable.

162528 | A001

6| Product description

3.1.9 Section defrosting

A differential pressure sensor measures the pressure drop over the exchanger’s extract/exhaust air side to detect any

frost build up in the exchanger. The system automatically calibrates the exchanger’s nominal pressure drop to obtain

the correct pressure limit in relation to the airflow. Manual calibration is possible and should be performed e.g. after

cleaning of exchanger.

A defrosting cycle is activated when differential pressure increases over set value. A signal from the control unit initiate

the dampers to close in sequence. The control unit will regulate the by-pass damper and exchanger dampers to de-

crease the heat recovery if the exhaust temperature drops below set value.

If the differential pressure increase over max. value, fan stop defrosting will start. The unit will re-start after defrosting.

If the pressure does not decrease, the air handling unit stops and an alarm is shown in the display. Make sure to melt

the ice before restarting the unit.

DM50-C CU27-C

EHA

PDT3

1 = Outdoor, 2 = Extract, 3 = Exhaust, 4 = Supply

DM50–C Control module

ADB1 By-pass damper

ADS1-3 Exchanger dampers

PDT3 Differential pressure sensor

EHS Exhaust temperature sensor

CU27–C Control unit

162528 | A001

Andere Handbücher für Topvex SC

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere System air Luftaufbereiter Handbücher

System air

System air Danvent DV-10 Bedienungsanleitung

System air

System air Rotovex 2400 EL Betriebsanleitung

System air

System air SAVE VTR 500 Handbuch

System air

System air Topvex SR 09, Topvex SR 11, Topvex TR 09 Bedienungsanleitung

System air

System air Topvex TR03 Fehlerbehebungshandbuch

System air

System air Danvent DV Bedienungsanleitung

System air

System air HHFlex Handbuch

System air

System air VSC 200 Bedienungsanleitung

System air

System air SAVE-P VTR 250/B Bedienungsanleitung

System air

System air changeair Freshman Series Bedienungsanleitung

System air

System air Topvex TR09 HWL Bedienungsanleitung

System air

System air DVV-XS Bedienungsanleitung

System air

System air MAXI 1100 EL Bedienungsanleitung

System air

System air Topvex TR04 Handbuch

System air

System air SAVE VTC 700 Bedienungsanleitung

System air

System air Topvex 1000 R Handbuch

System air

System air Topvex TR03 Bedienungsanleitung

System air

System air Geniox 10 Bedienungsanleitung

System air

System air Topvex 1000 R Bedienungsanleitung

System air

System air Topvex SC Series Bedienungsanleitung

System air

System air Topvex SX/C Series Bedienungsanleitung

System air

System air GEO 300 Bedienungsanleitung

System air

System air TOPVEX-1000 R Handbuch

System air

System air SAVE VSC 100 Bedienungsanleitung

Beliebte Luftaufbereiter Handbücher anderer Marken

Klimor

Klimor EVO-S Bedienungsanleitung

Salda

Salda SMARTY XP Leitfaden

BLAUBERG

BLAUBERG KOMFORT Roto EC S400 Bedienungsanleitung

Trenton

Trenton TPLP Series Bedienungsanleitung

Kemper

Kemper CleanAirTower Bedienungsanleitung

Daikin

Daikin DV PTC 14 Series Bedienungsanleitung

Haier

Haier HB2400VA1M20 Bedienungsanleitung

Webasto

Webasto BlueCool A-Series Bedienungsanleitung

RDZ

RDZ DA 701 Technisches Dokument

Carrier

Carrier 39T Abmessungen und Installationsanleitung

Armstrong Air

Armstrong Air BCE5V Series Bedienungsanleitung

ActronAir

ActronAir CAY500T Bedienungsanleitung

Carrier

Carrier 40MBDAQ Bedienungsanleitung

Allied

Allied A93UH1E Bedienungsanleitung

Nortek

Nortek B6VMAI Bedienungsanleitung

TemperZone

TemperZone Econex Pro OPA 1410RLTM4FPQD Wartungs- und Serviceanleitung

RDZ

RDZ WHR 200 Technisches Dokument

AAON

AAON H3 Series Betriebsanleitung