System Sensor M500M Bedienungsanleitung

SS-460-004 1 I56-3855-001

M500M Monitor Module

INSTALLATION AND MAINTENANCE INSTRUCTIONS

3825 Ohio Avenue, St. Charles, Illinois 60174

1-800-SENSOR2, FAX: 630-377-6495

www.systemsensor.com

BEfORE INSTALLINg

This information is included as a quick reference installation guide. Refer to

the control panel installation manual for detailed system information. If the

modules will be installed in an existing operational system, inform the opera-

tor and local authority that the system will be temporarily out of service. Dis-

connect power to the control panel before installing the modules.

NOTICE: This manual should be left with the owner/user of this equipment.

gENERAL DESCRIpTION

The M500M Monitor Module is intended for use in intelligent, two-wire sys-

tems, where the individual address of each module is selected using the built-

in rotary decade switches. It provides either a 2-wire or 4-wire fault tolerant

initiating circuit for normally open contact fire alarm, supervisory, or security

devices. The module has a panel controlled LED indicator.

COMpATIBILITy REqUIREMENTS

To ensure proper operation, these modules shall be connected to listed com-

patible system control panels only.

fIgURE 1. CONTROLS AND INDICATORS:

C0917-01

SpECIfICATIONS

Normal Operating Voltage: 15 to 32 VDC

Maximum Current Draw: 5.0mA (LED on)

Average Operating Current: 350 μA, 1 communication every 5 seconds, 47k EOL

EOL Resistance: 47K Ohms

Maximum IDC wiring resistance: 40 Ohms

Maximum IDC Voltage: 11 Volts

Maximum IDC Current: 400μA

Temperature Range: 32˚F to 120˚F (0˚C to 49˚C)

Humidity: 10% to 93% Non-condensing

Dimensions: 41/2˝ H x 4˝ W x 1

1/4˝ D (Mounts to a 4˝ square by 21/8˝ deep box.)

Accessories: SMB500 Electrical Box

MOUNTINg

The M500M mounts directly to 4-inch square electrical boxes (see Figure 2).

The box must have a minimum depth of 21/8inches. Surface mounted electri-

cal boxes (SMB500) are available from System Sensor.

fIgURE 2. MODULE MOUNTINg:

ISOLATED

QUADRANT

C1044-00

WIRINg

NOTE: All wiring must conform to applicable local codes, ordinances, and

regulations. This module is intended for power limited wiring only.

1. Install module wiring in accordance with the job drawings and appropri-

ate wiring diagrams.

2. Set the address on the module per job drawings.

3. Secure module to electrical box (supplied by installer), as shown in

Figure 2.

I56-3855-001

firealarmresources.com

SS-460-004 2 I56-3855-001

System Sensor warrants its enclosed product to be free from defects in materials and

workmanship under normal use and service for a period of three years from date of

manufacture. System Sensor makes no other express warranty for the enclosed product.

No agent, representative, dealer, or employee of the Company has the authority to in-

crease or alter the obligations or limitations of this Warranty. The Company’s obligation

of this Warranty shall be limited to the replacement of any part of the product which

is found to be defective in materials or workmanship under normal use and service

during the three year period commencing with the date of manufacture. After phoning

System Sensor’s toll free number 800-SENSOR2 (736-7672) for a Return Authorization

number, send defective units postage prepaid to: System Sensor, Returns Department, RA

fIgURE 3. TypICAL 2-WIRE INITIATINg CIRCUIT CONfIgURATION, NfpA STyLE B:

(+)

(–)

(+)

(–)

(+)

(–)

MONITOR

MODULE

ANY NUMBER OF UL LISTED

CONTACT CLOSURE DEVICES

MAY BE USED. DO NOT MIX FIRE

ALARM INITIATING,

SUPERVISORY, OR SECURITY

DEVICES ON THE SAME MODULE.

TO NEXT

DEVICE

FROM PANEL OR

PREVIOUS DEVICE

47K EOL

RESISTOR

ELR-47K

CONNECT MODULES TO LISTED

COMPATIBLE CONTROL PANELS ONLY

SIGNAL LINE CIRCUIT (SLC)

32 VDC MAX.

SHIELDED-TWISTED PAIR

IS RECOMMENDED

ALL WIRING SHOWN IS SUPERVISED AND POWER LIMITED

INITIATING DEVICE CIRCUIT (IDC) - NFPA STYLE B

POWER LIMITED: 400µA MAX. @ 11 VDC MAX

INSTALL CONTACT CLOSURE DEVICES PER

MANUFACTURER’S INSTALLATION INSTRUCTIONS.

C1051-00

fIgURE 4. TypICAL 4-WIRE fAULT TOLERANT INITIATINg CIRCUIT CONfIgURATION, NfpA STyLE D:

(+)

(-)

(+)

(–)

(+)

(–)

MONITOR

MODULE

TO NEXT

DEVICE

FROM PANEL OR

PREVIOUS DEVICE

CONNECT MODULES TO LISTED

COMPATIBLE CONTROL PANELS ONLY

SIGNAL LINE CIRCUIT (SLC)

32 VDC MAX.

SHIELDED-TWISTED PAIR

IS RECOMMENDED

ALL WIRING SHOWN IS SUPERVISED AND POWER LIMITED

ANY NUMBER OF UL LISTED

CONTACT CLOSURE DEVICES

MAY BE USED. DO NOT MIX FIRE

ALARM INITIATING,

SUPERVISORY, OR SECURITY

DEVICES ON THE SAME MODULE.

INSTALL CONTACT CLOSURE DEVICES PER

MANUFACTURER’S INSTALLATION INSTRUCTIONS.

EOL RESISTOR

IS INTERNAL AT

TERMINALS

8 AND 9

C0919-03

ThREE-yEAR LIMITED WARRANTy

#__________, 3825 Ohio Avenue, St. Charles, IL 60174. Please include a note describing

the malfunction and suspected cause of failure. The Company shall not be obligated to

replace units which are found to be defective because of damage, unreasonable use,

modifications, or alterations occurring after the date of manufacture. In no case shall the

Company be liable for any consequential or incidental damages for breach of this or any

other Warranty, expressed or implied whatsoever, even if the loss or damage is caused by

the Company’s negligence or fault. Some states do not allow the exclusion or limitation of

incidental or consequential damages, so the above limitation or exclusion may not apply

to you. This Warranty gives you specific legal rights, and you may also have other rights

which vary from state to state.

firealarmresources.com

Andere System Sensor Steuereinheit Handbücher

System Sensor

System Sensor SC-6 Bedienungsanleitung

System Sensor

System Sensor M502M Bedienungsanleitung

System Sensor

System Sensor M502MA Bedienungsanleitung

System Sensor

System Sensor M500SA Bedienungsanleitung

System Sensor

System Sensor IM-10 Bedienungsanleitung

System Sensor

System Sensor MOD400R Bedienungsanleitung

System Sensor

System Sensor MDL3W Bedienungsanleitung

System Sensor

System Sensor Supervised Control Module M500S Bedienungsanleitung

System Sensor

System Sensor i3 Series Bedienungsanleitung

System Sensor

System Sensor I4 Series Bedienungsanleitung

System Sensor

System Sensor M500DMR Bedienungsanleitung

System Sensor

System Sensor RR1 Bedienungsanleitung

System Sensor

System Sensor M210E Bedienungsanleitung

System Sensor

System Sensor M502M Bedienungsanleitung

System Sensor

System Sensor EM-1MI Bedienungsanleitung

System Sensor

System Sensor M902M Bedienungsanleitung

System Sensor

System Sensor M500SAP Bedienungsanleitung

System Sensor

System Sensor M500S Bedienungsanleitung

System Sensor

System Sensor M500FP Bedienungsanleitung

System Sensor

System Sensor M500M Bedienungsanleitung

System Sensor

System Sensor CR-6 Bedienungsanleitung

System Sensor

System Sensor M500FP Bedienungsanleitung

System Sensor

System Sensor CZ-6 Bedienungsanleitung

System Sensor

System Sensor 500 Series Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung