System Sensor TELAIRE Innovair CD100VC Bedienungsanleitung

CO2Ventilation Controller

User Manual

CD100VC

Featuring

Prepare for installation by

using the mounting holes

configured for US or

European junction boxes.

3 .

4 .

Mount the

Controller on the

base by aligning

the top clips and

then securing to

the bottomclips. A

“snap” sound will

indicate that the

sensor is secure.

The sensor will

now have power.

In less than 2 minutes, the

sensor will stabilize and display

the “Normal Mode” (current

CO2readings).

At this point one of nine

preset programs or one

custom channel can be

selected for operation. Use

the charts below to select a

preset or to select/modify

sensor settings.

5 . Finish installation by

sliding the cover over

the menu keys and

secure with the

supplied screw.

1 . 2 . Secure the Mounting Plate to

the wall or junction box and

make necessary wire

connections.

Installation

Use the mounting plate

as a template to mark

mounting and wiring

holes.

6 . Ready for

operation!

Terminal Block Designations

1 Not Used

2 Not Used

3 Relay Norm Open

4 Relay Common

5 Relay Norm Closed

6 4-20mA Output

7 Signal Ground

8 0-10V Output

1 AC+ / DC+

2 AC- / GND

firealarmresources.com

Altitude Correction and TEMA (On/Off)

1. Press +and hold (at least 5 seconds) until the sensor enters the

edit mode.

2. The first menu will be the Altitude correction. The adjustments will in-

crease/decrease in 500 ft. increments. To do this use the Up/Down Rocker

Button to adjust to the proper altitude.

3. Press to lock in value then press to proceed to TEMA.

4. Use the Up/Down Rocker Button to switch to On or Off.

5. Press to lock in value then press to proceed to Normal Mode.

Note: It is recommended that the TEMA feature is left on for the best

sensor operation.

Standard and Non-Standard Settings

The Non-Standard settings can be changed at any time after the sensor is

powered up. These settings have 7 variables and follow in sequence with the

Preset/Variable chart (see reverse side of this sheet). The Altitude and TEMA

feature can be changed without entering into the Non-Standard mode.

The Standard Settings (see reverse side of this sheet) are factory set and

cannot be changed. Like the Non-Standard settings, Altitude and TEMA can be

changed.

Select a Preset (from the STDSET Menu)

1. Press + and hold (at least 5 seconds) until the sensor enters the

edit mode.

2. Press 2 times. You will enter the “STDSET” Menu.

3. Use the Up/Down Rocker Button to select the Preset number.

Use the

“Preset” chart (on reverse side of this sheet) to select the desired

“Variables”

4. Press to lock in selection then press to return to monitoring mode.

For Custom Settings (from the NONSTD Menu)

1. Press + and hold (at least 5 seconds) until the sensor enters the

edit mode.

2. Press 2 times. You will enter the “STDSET” Menu.

3. Use the Up/Down Rocker Button to toggle to the “NONSTD” Menu and

press .

4. Use the Up/Down Rocker Button to scroll through the 8 variables. The

variables begin with customizing the ppm levels and end with hysterisis.

5. Press to move through variables. Use the Up/Down Rocker to toggle to

desired setting.

6. Press to lock in selection then press to continue to next Variable.

Software Operation

Your new Innovair™ CD100VC CO2Ventilation Controller uses state-of-the-art

dual beam Absorption Infrared™ Technology. This patented technology

provides a stable, accurate and reliable sensor.

The sensor is also equipped with Engelhard Sensor Technologies’ patented

TEMA (Time Extended Measurement Algorithm) software. The TEMA software

will automatically sense and adjust for any sensor drift minimizing calibration

frequency to once every five years.

The Ventilation Controller is shipped with 9 preset settings (named Standard

Sets) and one setting for customizing (named Non-Standard). Two additional

settings are available; altitude adjustments and TEMA (on/off). These two are

accessible without entering the Standard or Non-Standard settings.

firealarmresources.com

Specifications

Method

Dual Beam Absorption Infrared™

Patented TEMA self calibration

software

Sample Method

Diffusion or flow-through (50-100 ml/min)

Performance

Measurement Range

Analog output: 0-2000 ppm factory

default - Adjustable to 10,000 ppm

Digital display: 0-10,000 ppm

Sensitivity

±10 ppm

Resolution

±1 ppm

Accuracy

Typical conditions 60-90°F (15-32°C):

0-2000 ppm: ±50 ppm or ±3% of

reading, whichever is greater

2,000-10,000 ppm: ±5% of reading

Extended conditions

32-122°F (0-50°C):

0-2000 ppm: ±100 ppm or ±5% of

reading, whichever is greater

2,000-10,000 ppm: ±7% of reading

Elevation (Pressure) Correction

Add 0.13% of reading per mm Hg

decrease from 760 (On-board

correction, user set)

Annual Drift

±10 ppm (negligible) with TEMA on

±20 ppm typical with TEMA off

Response Time 0..90% FS

<2 min.

Warm-Up Time @ 25°C

<2 minutes

Operating Conditions

0°- 50°C (32°-122°F)

0 - 95% RH, non-condensing

Storage Temperatures

–40°- 70°C

Agency Certification

FCC Part 15 Class B

Calibration Interval

Five years / zero ppm gas offset adjust

Input/Output

Power

18-36 VAC RMS, 50/60 Hz

18-42 VDC polarity protected/dependent

70 mA average, 100 mA peak, at 24 VDC

Analog CO2Output

0-10 VDC (100 Ohms output impedance)

4-20 mA (RLmax = 500 Ohms)

Both outputs available simultaneously

Relay

Normally Open or Normally Closed (wire

either way); gold bifurcated; 1 Amp at 24

VDC, resistive load, 2 Amp carrying

current. Adjustable setpoint, factory set

at 1000 ppm, 50 ppm hysteresis.

Wiring

18-28 AWG stranded copper wire only.

2 wires each for power, analog output,

relay.

Digital I/O

RS-232 interface

Note

CO2readings may be temporarily

affected in the presence of certain por-

table two-way radios and cellular phones.

Specifications subject to change without

notice. Covered by United States

Patents: 5,060,508 and 5,163,332.

Other patents pending.

Software Functionality

Featuring

System Sensor warrants its enclosed sensor to be free from defects in materials and workmanship under normal use and service for a period of 18 months from date of purchase by the

original owner. System Sensor makes no other express warranty for this sensor. No agent, representative, dealer, or employee of the Company has the authority to increase or alter the

obligations or limitations of this Warranty. The Companyís obligation of this Warranty shall be limited to the repair or replacement of any part of the sensor which is found to be defective in

materials or workmanship under normal use and service during the 18 month period commencing with the date of purchase by the original owner. After phoning System Sensorís toll free

number 800-SENSOR2 (736-7672) for a Return Authorization number, send defective units postage prepaid to: System Sensor, Warranty Service, RA#_______, 3825 Ohio Avenue, St.

Charles, IL 60174. Please include a note describing the malfunction and suspected cause of failure. The company shall not be obligated to repair or replace units which are found to be

defective because of damage, unreasonable use, modifications, or alterations occurring after the date of manufacture. In no case shall the Company be liable for any consequential or

incidental damages for breach of this or any other Warranty, expressed or implied whatsoever, even if the loss or damage is caused by the limitation of incidental or consequential

damages, so the above limitation or exclusion may not apply to you. This Warranty gives you specific legal rights, and you may also have other rights, and you may also have other rights

which may vary from state to state.

Warranty

Absorption Infrared™ is a trademark of Engelhard Sensor Technologies.

Telaire®is a registered trademark of Engelhard Sensor Technologies.

PN62511D - 31300

System Sensor

3825 Ohio Avenue St. Charles, IL 60174

1-800-SENSOR2 (736-7672) Fax: 630-377-6495

firealarmresources.com

Andere System Sensor Controller Handbücher