System Sensor Innovair 200 Series Bedienungsanleitung

The System Sensor Innovair™DH200 Series photoelectric air duct smoke detectors are

capable of sensing smoke in air velocities from 500 to 4,000 feet per minute (2.54 to

20.32 m/sec).

The DH200 Series Detector samples air currents passing through a duct and gives

dependable performance for shutdown of fans, blowers, and air conditioning systems,

preventing the spread of toxic smoke and ﬁre gases through the protected area.

These intelligent sensors communicate and are continuously monitored through the com-

munication line. Detector sensitivity changes caused by dirt, temperature, or humidity

are reported to the panel, allowing compensation algorithms to maintain the sensor’s set

sensitivity. An advance indication at the panel speciﬁes the sensor address, allowing for

selected maintenance to be performed as needed.

Remote alarm annunciation can be accomplished by using the RA400Z Remote

Annunciator or the RTS451 or RTS451KEY Remote Test Station. Both these devices

allow testing of the detector from a remote location.

The Innovair family is designed for simpliﬁed installation and easy maintenance. The

modular construction allows for easy cleaning and uncomplicated ﬁeld replacement of the

UL recognized power and sensor boards.

WARNING: Duct smoke detectors have speciﬁc limitations.

DUCT SMOKE DETECTORS ARE:

NOT a substitute for an open area smoke detector,

NOT a substitute for early warning detection, and

NOT a replacement for a building’s regular ﬁre detection system.

Refer to NFPA 72 and 90A for additional duct smoke detector application information.

Air velocity rating from 500 to 4000

feet per minute (2.54 to 20.32 m/sec.)

Patented telescopic sampling tube

Easily accessible code wheels

Outside mounting tabs

Easy and quick mounting to round

or rectangular ducts from 1′–12′

(0.3–3.7 meters) wide

Easy to clean

UL recognized ﬁeld-replaceable

power and sensor boards

Transparent cover for convenient

visual inspection

UL 268A listed

3-year warranty

DH200P (non-relay)

Has outputs for remote LED display,

remote test

Incorporates zener diodes to conserve

power for communications to other

devices

Com line power only

DH200RP (with relay)

Powered outputs for remote LED, remote

test and sounder

Two form “C”auxiliary contacts

Can be conﬁgured as a relay version or

jumpered to mimic a non-relay version

Patented cover tamper trouble signal

Requires both com line power and one of

the following: 24VAC/DC or

120/220VAC for operation

Intelligent Models Available

DH200P (non-relay)

DH200RP (with relay)

Product Overview

Innovair™200 Series

Intelligent

Duct Smoke Detectors

DH200P DH200RP

The duct smoke detector shall be a System

Sensor Model DH200P or DH200RP

Intelligent Series Duct Smoke Detector to

be used with compatible control panels.

The duct smoke detector shall be UL listed

per UL 268A, Standard for Smoke

Detectors for Duct Applications, speciﬁcal-

ly for use in air handling systems. The

detector shall operate in air velocities from

500 to 4000 feet per minute. The detector

shall be an intelligent photoelectronic

detector. It shall be capable of local testing

via magnetic switch or remote testing from

the RTS451 or RTS451KEY Remote Test

Station. The duct smoke detector housing

shall incorporate an airtight smoke cham-

ber in compliance with UL 268A. The

housing shall be capable of mounting to

either rectangular or round ducts without

adapter brackets. An integral ﬁlter system

shall be included to reduce dust and

residue effects, thereby reducing mainte-

nance and servicing. Sampling tubes shall

be easily installed after the housing is

mounted to the duct by passing through

the duct housing. Terminal connections

shall be of the strip and clamp method

suitable for 12-18 AWG wiring.

Architect/Engineer Speciﬁcations

Voltage Range

15 to 32 VDC

Standby Current

300µA @ 24 VDC (one communication

every 5 seconds with LED blink

enabled)

Wiring diagram for DH200P Duct Smoke Detector with optional RA400Z

(Must break tab on back of RA400Z when used with DH200P.)

Wiring diagram for DH200P Duct Smoke Detector with RTS451/RTS451KEY

TEST

RA400Z

RTS451

KEY

COMMON

COM(+)

COM(-)

TEST

RA400Z

RTS451

KEY

COMMON

COM(+)

COM(-)

–

COM (+)

COM (-)

COM (+)

COM (-)

COMMUNICATION

LINE

UL LISTED CONTROL

PANEL 1ST DETECTOR

IN LOOP 2ND DETECTOR

IN LOOP

TEST

RA400Z

RTS451

KEY

COMMON

COM(+)

COM(-)

RA400Z

COMMON

DH200P RTS451/RTS451KEY

TEST

RTS451

KEY

COM(+)

COM(-)

45 6

12 3

FIELD INSTALLED

JUMPER

COMMON TEST

LED RESET

FOR RTS451, TERMINAL 3 IS NOT USED.

(RTS451 DOES NOT HAVE ATERMINAL 6.)

FOR RTS451KEY, TERMINALS 3AND 6

ARE NOT USED.

TEST

RA400Z

RTS451

KEY

COMMON

COM(+)

COM(-)

RA400Z

COMMON

DH200P

RA400Z

Wiring diagram for DH200P Duct Smoke Detector using a UL listed control panel

DH200P Speciﬁcations

Device

Standby Alarm

RA400Z 0 mA 10 mA Max.

RTS451/RTS451KEY 0 mA 7.5 mA Max.

Accessory Current Loads

Current Requirements (using no accessories)

Power supply voltage

20-30 VDC 24 VAC, 50-60HZ 120VAC, 50-60Hz 220/240 VAC, 50-60Hz

Max. standby current 26 mA 65 mA RMS 44 mA RMS 25 mA RMS

Max. alarm current 87 mA 182 mA RMS 52 mA RMS 30 mA RMS

Alarm response time 3 to 17 sec. 3 to 17 sec. 3 to 17 sec. 3 to 17 sec.

Power up time 2 sec. 2 sec. 2 sec. 2 sec.

Device

Standby Alarm

PA400 0 mA 15 mA Max.

RA400Z 0 mA 12 mA Max.

RTS451/RTS451KEY 0 mA 10 mA Max.

Wiring diagram for DH200RP Duct Smoke Detector with optional RA400Z

Wiring diagram for DH200RP Duct Smoke

Detector with RTS451/RTS451KEY

Wiring diagram for DH200RP Duct Smoke Detector with optional PA400

Wiring diagram for DH200RP Duct Smoke Detector using a UL listed control panel

NOTE: Jumper J1 shunt must be installed for non-relay applications. J1 shunt must be removed for power supervision.

DH200RP Speciﬁcations

Alarm auxiliary contacts* (DPDT)

10 A @ 30 VDC

10 A @ 277 VAC (0.75 power factor)

240 VA @ 249 VAC (0.4 power factor)

1/8 HP @ 120 VAC

1/4 HP @ 240 VAC

Supervisory contact (SPST)

2.0 A @ 30 VDC (resistive)

*Minimum switching current for auxiliaty contact

must be 500 mA DC minimum @ 24 VDC.

Contact Ratings Accessory Current Loads at 24 VDC

–

COM (+)

COM (-)

COM (+)

COM (-)

COMMUNICATION

LINE

UL LISTED CONTROL

PANEL 1ST DETECTOR

IN LOOP 2ND DETECTOR

IN LOOP

1212

J1 JUMPER J1 JUMPER

57RA400Z

5 = Alarm Signal

7 = Aux. Power (—)

DO NOT BREAK TAB ON RA400Z

ALARM SIGNAL

AUX. POWER (—)

TEST +

TEST —

ALARM SIGNAL

NOT USED

CIRCUIT

REFERENCE

TEST

SWITCH

FOR RTS451, TERMINAL 3 IS NOT

USED. (RTS451 DOES NOT HAVE

ATERMINAL 6.) FOR RTS451KEY,

TERMINALS 3 AND 6 ARE NOT USED.

RTS 451/RTS451KEY

57PA400

5 = Alarm Signal

7 = Aux. Power (—)

NOTE: External power of 24V AC/DC

or 120/220 VAC must be connected in

order to power all remote horn or

strobe accessories.

Innovair™200 Series Specifications

Operating Temperature Range

32°to 131°F (0°to 55°C)

Operating Humidity Range

10% to 93% relative humidity

(non-condensing)

Duct Air Velocity

500 - 4000 ft./min. (2.54 - 20.32 m/s)

Length

14-3/8”(37 cm)

Width

5-1/2”(14 cm)

Depth

2-3/4”(7 cm)

Ordering Information

Part No. Description

DH200P Innovair™intelligent photoelectric non-relay duct

smoke detector

DH200RP Innovair™intelligent photoelectric with relay duct

smoke detector

ST-1.5 Metal sampling tube duct widths 1’–2’

ST-3 Metal sampling tube duct widths 2’–4’

ST-5 Metal sampling tube duct widths 4’–8’

ST-10 Metal sampling tube duct widths 8’–12’

A5053 Replacement photoelectric sensor board

A5060 Replacement power board for DH200RP (w/relay)

A5067 Replacement power board for DH200P (w/o relay)

Accessories Description

RTS451 Remote test station (see below)

RTS451KEY Remote test station w/key (see below)

RA400Z Remote LED (see below)

PA400 Mini-Alert™Sounder (see below)

F36-09-11 Replacement filters

M02-04-00 Test magnet

P48-21-00 End cap for metal sampling tube

P48-55-00 End cap for plastic sampling tube

S08-39-01 Replacement photo insect screen

T80-71-00 Replacement plastic sampling tube

RTS451

Remote Test Station

(UL S2522)

RTS451KEY

Remote Test Station with

Key (UL S2522)

RA400Z

Remote

Annunciator

(UL S2522)

PA400

Mini-Alert™Sounder

(UL S3593)

Device can not be wired

directly to DH200P

(non-relay).

ALARM

RESET

ALARM

RESET TEST

System Sensor Headquarters

3825 Ohio Avenue

St. Charles, IL 60174

Ph: 800/SENSOR2

Fx: 630/377-6495

Documents-on-Demand

800/736-7672 x3

www.systemsensor.com

System Sensor Canada

Ph: 905.812.0767

Fx: 905.812.0771

System Sensor Europe

Ph: 44.1403.276500

Fx: 44.1403.276501

System Sensor in China

Ph: 86.29.524.6253

Fx: 86.29.524.6259

System Sensor in Singapore

Ph: 65.273.2230

Fx: 65.273.2610

System Sensor –Far East

Ph: 85.22.191.9003

Fx: 85.22.736.6580

System Sensor –Australia

Ph: 613.54.281.142

Fx: 613.54.281.172

System Sensor –India

Ph: 91.11.558.2119

Fx: 91.11.567.6815

System Sensor Sales and Service

Dieses Handbuch passt für folgende Modelle

Andere System Sensor Rauchmelder Handbücher

System Sensor

System Sensor OSI-RE-SS Bedienungsanleitung

System Sensor

System Sensor DNRA Bedienungsanleitung

System Sensor

System Sensor B501 Bedienungsanleitung

System Sensor

System Sensor D4P120 Bedienungsanleitung

System Sensor

System Sensor BEAM1224 Bedienungsanleitung

System Sensor

System Sensor 2251B Bedienungsanleitung

System Sensor

System Sensor B210LP Bedienungsanleitung

System Sensor

System Sensor FAAST 7100X Bedienungsanleitung

System Sensor

System Sensor 2112/24S Bedienungsanleitung

System Sensor

System Sensor 2112/24R Bedienungsanleitung

System Sensor

System Sensor InnovairFlex D4240 Bedienungsanleitung

System Sensor

System Sensor DH500 Bedienungsanleitung

System Sensor

System Sensor Innovair DH100LP Bedienungsanleitung

System Sensor

System Sensor ECO1003ABL Bedienungsanleitung

System Sensor

System Sensor 2400 Bedienungsanleitung

System Sensor

System Sensor ED-P Bedienungsanleitung

System Sensor

System Sensor 2D51A Bedienungsanleitung

System Sensor

System Sensor 2112ж 24ATR Bedienungsanleitung

System Sensor

System Sensor 2012/24AUS Bedienungsanleitung

System Sensor

System Sensor B401BH-2 Bedienungsanleitung

System Sensor

System Sensor INNOVAIR DH100ACDCP Bedienungsanleitung

System Sensor

System Sensor Innovair DH200PL Bedienungsanleitung

System Sensor

System Sensor FSB-200 Bedienungsanleitung

System Sensor

System Sensor 2WTR-B Bedienungsanleitung

Beliebte Rauchmelder Handbücher anderer Marken

x-sense

x-sense SD19-W Bedienungsanleitung

BRK electronic

BRK electronic First Alert P1010 Bedienungsanleitung

FireAngel

FireAngel Thermoptek ST-622 Bedienungsanleitung

teko

teko Astra-42A Bedienungsanleitung

Safetec

Safetec SDS-2/6 Betriebsanleitung

Siemens

Siemens PE-11C Bedienungsanleitung

Resolution Products

Resolution Products RE612 CryptiX Bedienungsanleitung

First Alert

First Alert PC900V Bedienungsanleitung

Eminent

Eminent EM6590 E-Domotica Bedienungsanleitung

Ei Electronics

Ei Electronics Ei Ei168RC Bedienungsanleitung

Carrier

Carrier Kidde Quell Q301 Bedienungsanleitung

VESDA

VESDA VLF-500 Bedienungsanleitung

ELRO

ELRO FS8110 Bedienungsanleitung

Heiman

Heiman SMOKI NS-626PHS Bedienungsanleitung

Regin

Regin SDD-S65 Bedienungsanleitung

Family Gard

Family Gard FG225 Bedienungsanleitung

Greystone

Greystone DSD120 Bedienungsanleitung

Aparton

Aparton ASD-10 Bedienungsanleitung