TAGLab BAT 100 Bedienungsanleitung

BAT 100

Battery Tester

User Manual

Battery Tester User Manual (EN) ---------------------------------------------------------------------------------------- 1~10

__________________________________________________________________________________________________________________

TAGLab Battery Tester | BAT 100

Battery Tester User Manual

1 Safety Handle

Terminal connection cable (-) with clamp (black)

3 Terminal connection cable (+) with clamp (red)

4 Battery Analysis label (on back of tester)

5 Clear View Display Meter

6 Rocker Load Switch

__________________________________________________________________________________________________________________

TAGLab Battery Tester | BAT 100

Contents

Introduction

Scope of delivery ------------------------------------------------------------------------------------------------------------ 4

Technical data ---------------------------------------------------------------------------------------------------------------- 4

Safety ---------------------------------------------------------------------------------------------------------------------------- 5

Product Description -------------------------------------------------------------------------------------------------------- 6

Operation

Before Use -------------------------------------------------------------------------------------------------------------------- 6

Battery Test ------------------------------------------------------------------------------------------------------------------- 7

Starter Test ------------------------------------------------------------------------------------------------------------------- 9

Charging System Test ----------------------------------------------------------------------------------------------------- 9

Information

Care ---------------------------------------------------------------------------------------------------------------------------- 10

Disposal ----------------------------------------------------------------------------------------------------------------------- 10

Warranty ---------------------------------------------------------------------------------------------------------------------- 10

__________________________________________________________________________________________________________________

TAGLab Battery Tester | BAT 100

Introduction

• Explanation of symbols and pictograms used in this user manual and or the device:

You must follow these instructions prior to each use of the device

Follow warnings and safety instructions

Warning : Hot Surface. DO NOT TOUCH.

Never dispose the electrical equipment with daily waste

• Carefully study the user manual. The user manual should be kept in a safe place and submitted

together with the device in the event of this changing hands.

• Thank you for purchasing TAGLab BAT 100 Battery Tester.

• The TAGLab BAT 100 is suitable for testing open and a variety of closed, maintenance-free lead-acid

batteries as found in bike, cars, boats, and other vehicles, e.g.

o WET batteries (Wet) Lead-acid batteries (liquid electrolyte)

o GEL batteries (gel-type electrolyte)

o AGM batteries (electrolyte inside absorbed glass matt)

o Maintenance-free lead-acid batteries (MF)

• The device is designed to test 6V and 12V lead acid batteries.

• This device is not intended for use by children or persons with limited mental capacity or lacking experience

and or lacking expertise. Children should be supervised to ensure they do not play with the device.

• Any other use or modification of the device is considered improper and involves significant risks. The

manufacturer assumes no liability for damages due to improper use.

• On initial use of the battery tester, smoke may develop. This is caused by the lubrication burning off the

heater coils. This will not affect the performance of the tester and will diminish upon further use.

__________________________________________________________________________________________________________________

TAGLab Battery Tester | BAT 100

Scope of Delivery

• Tester

• Terminal Connection Cable with Clamps

• User Manual

Technical Data

Model BAT 100

Battery Type 6V 12V Lead Acid Batteries

Battery Capacity ~ 1000 CCA

Load Amp 100A

Load Test 100A 12V

50A 6V

Voltage Range 0 – 16V

Display Meter Analog Display with Colour Scale

Accuracy ± 0.2V

Test Cycle Maximum 10 seconds per test

Minimum 1 minute cool down after each test

Maximum 3 tests in 5 minutes

__________________________________________________________________________________________________________________

TAGLab Battery Tester | BAT 100

Safety

General Safety Guidelines

• Read all safety guidelines and instructions. Non-compliance with safety guidelines and instructions can

cause electric shock, fire and or serious injury. Keep all safety guidelines and instructions for future

reference.

Precaution

• Always perform testing in a well-ventilated area.

• Never operate the device if the cable is damaged. It must be repaired or replaced by a qualified technician.

• Make sure that the acid of the battery does not come into contact with the skin or clothing as it may cause

burns. However, if this happens then rinse the affected area immediately with water and contact your

physician immediately. Never trip the battery as acid may leak. Always wear safety goggles and protective

gloves.

• Do not place the battery on top of the tester or vice versa. Do not place other equipment on top of the tester.

• Do not pour liquid on the tester as there is a risk of electrocution. Never cover the tester when the device is

in operation. Make sure there is no risk of explosive or flammable substances e.g. gasoline or solvent, being

ignited whilst using the tester.

• Do not expose to heat or an excessive source of light. Keep the tester away from naked flames, hot surfaces

and sparks. Do not smoke or have open flames near the battery.

• Never disassemble the tester or attempt to repair the device. For inspection and repair, take it to a qualified

technician. Remove all device cables from the battery before attempting to drive your vehicle.

• Do not drop the Battery Tester as it may affect proper operation.

Warning

Life-threatening danger to infants and children! Never leave children unsupervised with the packing material as this

can cause suffocation. Do not allow children to play with cables – strangulation hazard.

The manufacturer is not responsible for damages caused by:

• Improper connection and or operation. Any type of modification to the device.

• Exterior force, damage to the device and or damage to parts of the device caused by mechanical impact or

overload. Moisture and or insufficient ventilation.

• Use of the device for purposes that are not described in this instruction manual.

• Consequential damages caused by non-intended and or improper use, and or defective batteries.

• The unauthorised opening of the device.

• This will void the Warranty.

__________________________________________________________________________________________________________________

TAGLab Battery Tester | BAT 100

Product Description

• TAGLab BAT 100 is designed for performing battery test, starter test and charging system test for wide

range of lead acid batteries used for passenger cars, commercial vehicles, motorcycles and certain other

vehicles – e. g. WET batteries (with liquid electro-lyte), GEL batteries (with electrolyte in gel form) or AGM

(absorbent glass mat) batteries.

• It can test 6V and 12V lead acid batteries.

• It can deliver a maximum 100A load.

Operation

Before use

• Make sure the terminals are clean, if required clean them with a brush and apply special grease to protect

the terminals.

• Refer to the user manual of the battery being tested for testing instructions and precautions prior to using the

tester.

• Do not allow the two clamps from the testing cable to touch each other. Only touch the insulated part of the

clamps.

• Do not connect the clamps or the battery poles through conductive tools or objects.

• Do not connect the tester to the battery while the engine is running. Turn the engine off before connecting.

• Undercharged lead-acid batteries will freeze during cold weather. Do not test or charge a frozen battery.

• Do not smoke or have open flames near the battery.

• Never remove tester clamps while testing.

• Never touch the clamps and the terminals with wet hands.

• Do not pull the clamps from the terminals by pulling on the clamp cables.

• Do not touch the cooling vents on the tester during or immediately after testing the battery. They become

very HOT.

• When placing the tester in the vehicle’s engine compartment, take special care that the metal housing of the

tester does not come in contact with either terminal of the battery or other electrical connections.

• First check if the needle of the tester points to zero position, if not, adjust the zero adjuster accordingly.

• After connecting the clamps, the needle should move to the right side, if it doesn’t move or moves in the

other direction, check the clamps for reverse connection or loose connection.

__________________________________________________________________________________________________________________

TAGLab Battery Tester | BAT 100

Battery Test

• Connect the red (+) terminal connector cable to the positive (+) terminal of the battery.

• Connect the black (-) terminal connector cable to the negative (-) terminal of the battery.

• With both the battery clamps connected, the tester’s display meter will show the battery’s current state of

charge.

• Engine and al electrical accessories must be off when testing battery.

• If it is less than 12V, disconnect the battery and recharge before re-testing.

• If recharging will not bring the reading above 12V, the battery is defective.

• Press and hold the load switch “ON” for 10 seconds to apply the load to the battery.

• Keep the load switch “ON” till the needle is steady. However do not exceed 10 seconds.

• Read meter with load switch “ON”.

• Release the battery load switch and remove the battery clamps from the battery.

• Refer to the battery analysis table on back of tester or in user manual

Cold Temperature Effects

• A battery will test lower when cold than when warm. For more accurate results, please reduce the battery’s

nominal rating by 200 CCA (one step on meter scale) for each 10°C drop below +5°C. If display meter CCA

rating is 800 and battery temperature is -5°C, read the same as 600 CCA (i.e. 1 step down).

Temperature Compensation

Battery Temperature -5°C

-15°C

-25°C

Decrease Rating by 1 Step

2 Step

3 Step

1 Step = 00 CCA

__________________________________________________________________________________________________________________

TAGLab Battery Tester | BAT 100

BATTERY ANALYSIS

(Read Meter with LOAD Switch ON for MAXIMUM 10 Seconds)

LOAD TEST BATTERY CONDITION

Good (Green)

Battery capacity is OK. Battery may or may not be fully

charged. Check specific gravity of battery to determine

state of charge. If specific gravity is less than full charge,

check for electrical drain or possible charging system

trouble. Recharge battery to full level.

Weak or Bad,

but Needle

remains Steady

(Yellow or Red)

Battery capacity is not satisfactory. Battery may be either

defective or not fully charged. Check specific gravity to

determine which condition exists. If charging does not bring

specific gravity to full charge level, battery should be

replaced.

Weak or Bad,

but Needle

remains Failing

(Yellow or Red)

Battery may be defective or very run down. Release load

switch and note volt meter reaction. Voltage recovery to 12

volt or above within seconds indicates defective battery.

Slow voltage recovery indicates run down condition. For

best results, check specific gravity.

Charging System

(White)

If the display meter needle reads OK, charging system is

functional. If it falls on the low red or high red areas,

charging system may be malfunctioning.

__________________________________________________________________________________________________________________

TAGLab Battery Tester | BAT 100

Starter Test

• Connect the red (+) terminal connector cable to the positive (+) terminal of the battery.

• Connect the black (-) terminal connector cable to the negative (-) terminal of the battery.

• Perform the battery test and note the exact voltage (Load Volts) with the load test on.

• If voltage continues to fall after 10 seconds, this test cannot be preformed.

• Do not press the rocker load switch during the following test.

• Disable the ignition system so the engine will not start,

• Crank the engine and note the exact voltage during cranking.

• Now refer the noted Load Volts and cranking voltage in the following starter test table.

• If cranking voltage is below the min. crank volts in following starter test table, the starter current draw is

excessive.

• Excessive starter current draw makes starting difficult and shortens the battery life. If starter cranks slowly,

check for high resistance or poor connections.

LOAD VOLTS 10.2

10.4

10.6

10.8

11.0

11.2

11.4

MIN. CRANK VOLTS 7.7

8.2

8.7

9.2

9.7

10.2

10.6

STARTER TEST

(Use the next higher Min. Crank Volts for the engine of less than 200 CID)

Charging System Test

• Do not press the rocker load switch during this test.

• Connect the red (+) terminal connector cable to the positive (+) terminal of the battery.

• Connect the black (-) terminal connector cable to the negative (-) terminal of the battery.

• Operate the engine at fast idle. e.g. 1200 - 1500 rpm.

• View the display meter and read the “charging system” scale located on the far right side of the display

meter.

• Note meter reading with all electrical accessories off. It should be in green area in “charging system” scale.

• With headlights and blower motor on high, meter should remain in green area.

• If display meter needle falls in red area or outside the charging system area, then “charging system“ is

malfunctioning.

Andere Handbücher für BAT 100

Inhaltsverzeichnis

Andere TAGLab Prüfgeräte Handbücher

TAGLab

TAGLab BAT 100 Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Vernier

Vernier Go Direct Voltage Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung