Talos Security WASPIR01 Bedienungsanleitung

Talos Security WASPIR01

Wireless DVR PIR Alarm System

CONTENTS

I. Introduction ------------------------------------------------------------------------------ 3

II. Features------------------------------------------------------------------------------------------3

III. Product Overview-----------------------------------------------------------------------------4

1. Technical parameters-----------------------------------------------------------------------4

2. Recommended Scan------------------------------------------------------------------------4

3. Time and date set up------------------------------------------------------------------------5

4. Installation--------------------------------------------------------------------------------------5

5. Turn on and Start:----------------------------------------------------------------------------5

6. Arm operation---------------------------------------------------------------------------------5

7. Disarm operation-----------------------------------------------------------------------------5

8. Automatic recording-------------------------------------------------------------------------5

9. Emergency Alarm-----------------------------------------------------------------------------5

10. Recording Indication------------------------------------------------------------------------5

11. Playback of recorded video---------------------------------------------------------------6

12. Adding wireless accessories-------------------------------------------------------------6

13. Removing wireless accessories---------------------------------------------------------6

IV. Wireless Remote Controller----------------------------------------------------------------6

1. Features------------------------------------------------------------------------------------------6

2. Technical Parameters------------------------------------------------------------------------6

3. Installation and Use---------------------------------------------------------------------------6

4. Adding or removing a connection with alarm host--------------------------------7

V. Wireless Door Magnetic Sensor-----------------------------------------------------------7

1. Features------------------------------------------------------------------------------------------7

2. Technical Parameters------------------------------------------------------------------------7

3. Installation and Use--------------------------------------------------------------------------7

VI. Wireless Sound and Flash Siren ----------------------------------------------------------------7

1. Features -----------------------------------------------------------------------------------------7

2. Technical Parameters------------------------------------------------------------------------7

3. Installation and Use--------------------------------------------------------------------------7

4. Adding a wireless connection with the alarm host-------------------------------8

VII. Cautions-------------------------------------------------------------------------------------------------8

I. Introduction:

This product is suitable to work with alarm system .It’s a new hi-tech product which can

automatically take and save audios and videos of the area where alarm events occur. Helpful

for evidence obtain. It has a wide application range such as home, office, hotel, market place,

store, villa, museum and warehouse etc. and any other kind of places which needs special

protection.

The package mainly contains: 1pc wireless DVR PIR alarm, 1pc SD card (4GB), 1pc USB

cable, 1pc power adaptor, 2 remote controls and 1 wireless siren. Please read below

instructions carefully before using.

II. Features:

1. Intelligent microchip control, good performance and reliable quality.

2. Wide-angle PIR detection, special temperature compensation circuit design, wireless signal

transmission.

3. Remote arm and disarm, system will automatically start audio and video recording and save

recorded files named by the starting time (year, month, date, hour, minute, second) of

recording.

4. Remote emergency alarm, automatically start audio and video recording.

5. Default (can be change according to special requirements) recording time for motion

detection is 1 minute , max 9 minutes for emergency alarm recording;

6. 4G default memory capacity and can be extended to 8G, 16G, 32G, files overwrite function,

data can be saved when power off, can connect with computers via data cable to read the

recording files.

7. DC power supply with rechargeable backup battery, backup battery up to 3 hours.

8. Automatic visual prompt for easy identification of recordings.

9. Connect up to 10 wireless sensors or remote controls.

III. Product Overview:

1. Technical parameters:

● Power Input：100~240VAC 50HZ/60HZ

● Backup Battery：3.7V rechargeable Lithium battery

● PIR Detector：Wide-Angle 100°8 * 8 m

● Static Current：< 60mA Working Current：< 110mA

● Wireless Frequency：433/860MHz（optional）

● Backup Battery Working Time：≤ 3 Hours

● Camera：1/6.5” OV CMOS Chip, 300, 000 pixels

● Video Format：AVI

● Recording Speed：30 fps

● Resolution：640*480, Min. illumination: 0.1 lux

● Focal Length：8mm

● Viewing Angle：35° (Vertical）60°（Horizontal）

● Transmission Mode：USB 2.0（Hs）

● Recording Time: 1 minute (can be customized)

● Memory Capacity：4GB SD card

● Product Dimension：103 * 60 * 32(mm）

● Video format request system ：Windows ME/ 2000/ XP/ Mac OS 9.2.2 or higher version

（Windows 98 requires driver installation）

2. Recommended Scan: We recommend a virus scan of any new media device that is

installed on your computer. Make sure SD card is installed, slide backup battery switch to the

left off position, connect the device to the computer with the USB cable and then you will see

the removable drive appear, scan the drive for any virus.

3. Time and date set up:

3.1 Double click the moveable disk to find the “Get Sys Time” file.

3.2 Click the file and then click Get Systime.exe; you will then see the Get System Time icon.

3.3 Click the icon “get system time” Success for time setting will be displayed within a few

seconds.

3.4 Click OK and then click Cancel. Open the moveable disk again and you should see the

systime.bin file.

4. Installation:

Fix the attached bracket on the proper position of the wall. (1.8~2.5M height from the floor is

suggested). Connect the

Output terminal to the power input port of the motion sensor, put the motion sensor onto the

mounting bracket and adjust the tilt for proper detecting and recording angle.

5. Turn on and Start:

Plug the power adapter after detecting angle and recording angle well adjusted. Turn on the

battery switch button, the

Device will go into standby mode; you will see a red light for 30 seconds during the boot up

process.

6. Arm operation:

Press arm key on the remote, you will hear one “beep” alarm goes into standby mode after 8

seconds.

7. Disarm operation:

Press disarm key on the remote, the device has two “beep” and the device is disarmed

immediately.

8. Automatic recording:

The Alarm camera will start a 1 minute audio and video recording upon motion trigger. A red

light will keep flashing all the time while recording and will go off automatically after recording

stops. Files will be saved automatically with a name code

9. Emergency Alarm:

Press emergency key on the remote, the device will start recording without sound indication.

The maximum recording time is 9 minutes. A red light will keep flashing all the time when

recording and will go off automatically after recording

10. Recording Indication:

10.1. A blue light will keep on for around 50 seconds after each recording finished.

10.2. Every time when you disarm the device from armed condition, a blue light will keep on for

around 50 seconds to indicate new recorded file.

11. Playback of recorded video:

11.1 Take the SD card out from the device on standby mode and insert it to the computer, you

can click and playback the recorded files in the moveable disk via computer. Then remove the

SD card from the computer in safe way and insert it to the motion sensor directly.

11.2 Turn off the backup battery switch of the motion sensor and connect it to the computer

with the USB data cable, you can click and playback the recorded files in the moveable disk.

Note：

1. When reviewing video files no other operation can be performed.

2. Install a supported video player, such as Storm Player, Kmplayer, Mplayer etc….

3. You will need to set the time according to the instructions every time before you remove the

alarm from the computer.

12. Adding wireless accessories: Press study button on the back side of the motion alarm,

after hear a “beep”, trigger the wireless accessories twice consecutively, the motion alarm has

5 “beeps” means the wireless accessory is successfully paired; 2 “beeps” means failure. You

need repeat above steps. If no study operations within 20 seconds, the motion alarm beeps

twice and exits from learning mode.

13. Removing wireless accessories:

Keep pressing the study button for 5 seconds and release you will hear a long beep,

(3 seconds) this indicates that the device has been deleted. This will remove ALL connections.

IV. Wireless Remote Controller

1. Features

1.1 Control the host to arm/disarm

1.2 Record with emergency button

2. Technical Parameters ：

2.1 Working Power: alkalinity 12V 27A battery

2.2 Emitting distance: ≥ 100m (without any objective air

condition)

2.3 Battery life: ≤ 2years

3. Installation and Use

3.1 DIY installation

3.2 Press Arm key to get alarm host make a “beep” sound, the alarm host goes into armed

condition. Press Disarm key to get two “beep” sounds to disarm successfully.

3.3 Please replace the battery after use of one year or the remote does not respond well.

4. Adding or removing a connection with alarm host (Sec III 12 & 13)

V. Wireless Door Magnetic Sensor

1. Features

1.1 Monitoring any door and window condition

1.2 Emitting alarm signal to alarm host once the door and window was open.

2. Technical Parameters ：

2.1 Working Power: alkalinity 12V 23A battery

2.2 Emitting distance: ≥ 150m

2.3 Battery life: ≤ 2years

2.4 Unobstructed distance: < 4m

3. Installation and Use

3.1 The magnet side fixed on the door, up to 1.6 meters above the ground to prevent

tampering.

3.2 The magnet control part fixed on the frame of the door, pay attention to keep same level

position with magnet side, the gap between two parts should be less than 10mm.

3.3 Indicator light keeps lighting means low voltage, please replace the battery.

VI. Wireless Sound and Flash Siren

1. Features ：

1.1 Working match with alarm host. Wireless receiving alarm signal,

On-site sound and flash alarm, max alarm time 3 minutes.

1.2 With power plug, normally installed indoor

2. Technical Parameters ：

2.1 Working Power: 100~240VAC

2.2 Static Current: <15 mA

2.3 Alarm Current : <200 mA

2.4 Receiving Distance: ≤100m （without any objective air condition.

3. Installation and Use:

Plug into a suitable power supply in the room. Suggested position is at least 6 feet from the

ground.

4. Matching or cancel the connection with alarm host

4.1 Connecting with alarm host

4.2 Power ON the siren and then press the study button, the siren lights up to indicate the

study mode is active.

4.3 Press the emitting button on the back of PIR/DVR detector twice consecutively.

4.4 The siren will flash 5 times if the connection is successful.

4.5 If the connection fails, please repeat above steps.

5. Cancel connection from alarm host

5.1 Keep pressing the study button for 5 seconds then release. The siren will flash once; this

indicates the connection is cancelled.

5.2 If the connection fails to cancel, please repeat the above operation.

Note:

1. Only one wireless device can be connected at a time.

2. Each DVR PIR detector can connect with many devices.

VII. Cautions:

1. Please abide by the applicable laws and regulations. Do not use this unit for other illegal

purposes or you should take all the responsibility.

2. Please do not use it at the environment which human can not living and do not place it in a

humid environment, this product is not waterproof.

3. Please do not face the camera to the sun or other strong light to avoid damaging of optics

parts.

4. Please do not use in a dusty environment. Keep its lens and other parts clean from dust to

avoid damage to the video recording or the operation of the product.

5. Please clean the lens with lens wiping paper or glasses towel periodically.

6. This product is precision electronic product and do not make it subject to any impact or

strong shake, do not use it in strong magnetic field or electric field.

Inhaltsverzeichnis

Andere Talos Security Sicherheitssystem Handbücher

Talos Security

Talos Security DK1400 Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

CADDX

CADDX NX-6 Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

Blaupunkt

Blaupunkt SA 2700 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Highway Safety Group

Highway Safety Group EA401 Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung