tams elektronik S88-3 Bedienungsanleitung
n
n
S88-3
n
s88-Rückmelder n
s88-Feedback Module n
Décodeur s88 n
s88-Terugmelder n
n
nAnleitung
nManual
nMode d´emploi
nHandleiding
n
Art.-Nr. 44-01305 / 44-01306 / 44-01307 n
n
n
n
n
nDeutsch 3
nEnglish 18
nFrançais 33
nNederlands 48
n
n
n
n
n
n
n
n
© 06/2008 Tams Elektronik GmbH
Alle Rechte, insbesondere das Recht
der Vervielfältigung und Verbreitung
sowie der Übersetzung vorbehalten.
Vervielfältigungen und Reproduktionen
in jeglicher Form bedürfen der
schriftlichen Genehmigung durch die
Tams Elektronik GmbH.
Technische Änderungen vorbehalten.
© 06/2008 Tams Elektronik GmbH
All rights reserved. No part of this
publication may be reproduced or
transmitted in any form or by any
means, electronic or mechanical,
including photocopying, without prior
permission in writing from Tams
Elektronik GmbH.
Subject to technical modification.
© 06/2008 Tams Elektronik GmbH
Tout droits réservés, en particulier les
droits de reproduction et de diffusion
ainsi que le traduction. Toute
duplication ou reproduction sous
quelque forme que ce soit nécessite
l´accord écrit de la societé Tams
Elektronik GmbH.
Sous réserve de modifications
techniques.
© 06/2008 Tams Elektronik GmbH
Alle rechten voorbehouden. Niets uit
deze publicatie mag worden
vermenigvuldigd opgeslagen of
openbaar gemaakt, zonder
voorafgaande schriftelijke toestemming
van Tams Elektronik GmbH.
Technische wijzigingen voorbehouden.
n
English S88-3
Page 18
Table of contents
1. Getting started 19
2. Safety instructions 20
3. Safe and correct soldering 23
4. Operation overview 24
5. Technical specifications 25
6. Assembling the S88-3 25
7. Connecting the S88-3 29
8. Check list for troubleshooting 30
9. Manufacturer's note, CE and Warranty 30
Parts list I.1
Printed Circuit Board (PCB) layout (Fig. 1) I.2
Circuit Diagram (Fig. 2) II
Connections diagram (Fig. 3) III
(Pages I to III in the centre of this handbook are removable.)
S88-3 English
Page 19
!
1. Getting started
How to use this manual
This manual gives step-by-step instructions for safe and correct
assembly of the kit and fitting of the ready-built module, and operation.
Before you start, we advise you to read the whole manual, particularly
the chapter on safety instructions and the FAQ chapter. You will then
know where to take care and how to prevent mistakes which take a lot
of effort to correct.
Keep this manual safely so that you can solve problems in the future. If
you pass the kit or the ready-built module on to another person, please
pass on the manual with it.
Intended use
The kit or the ready-built module can be assembled and operated with
a digital model railway to feedback data via the s88 bus using this
manual.
Any other use is inappropriate and invalidates any guarantees.
The kit and the ready-built module should not be assembled or fitted by
children under the age of 14.
Reading, understanding and following the instructions in this manual
are mandatory for the user.
Caution:
The circuit contains integrated circuits. These are very sensitive to static
electricity. Do not touch components without first discharging yourself.
Touching a radiator or other grounded metal part will discharge you.
English S88-3
Page 20
Checking the package contents
Please make sure that your package contains:
§one kit, containing the components listed in the parts and one PCB
or one ready-built module,
§an Ethernet patch cable (length: 0,5 m),
§one manual.
Required materials
For assembling the kit you need:
§an electronic soldering iron (max. 30 Watt) with a fine tip,
§a soldering iron stand,
§a tip-cleaning sponge,
§a heat-resistant mat,
§a small side cutter and wire stripper,
§a pair of tweezers and long nose pliers,
§tin solder (0,5 mm. diameter),
In order to connect the module you need wire. Recommended
diameters: >0,25 mm² for the connections to the rails.
2. Safety instructions
Mechanical hazards
Cut wires can have sharp ends and can cause serious injuries. Watch
out for sharp edges when you pick up the PCB.
Visibly damaged parts can cause unpredictable danger. Do not use
damaged parts: recycle and replace them with new ones.
Electrical hazards
§Touching powered, live components,
§touching conducting components which are live due to malfunction,
§short circuits,
§connecting the circuit to another voltage than specified,
S88-3 English
Page 21
§impermissibly high humidity,
§condensation build up
can cause serious injury due to electrical shock. Take the following
precautions to prevent this danger:
§Never perform wiring on a powered module.
§Assembling and mounting the kit should only be done in closed,
clean, dry rooms. Beware of humidity.
§Only use low power for this module as described in this manual and
only use certified transformers.
§Connect transformers and soldering irons only in approved mains
sockets installed by an authorised electrician.
§Observe cable diameter requirements.
§After condensation build up, allow a minimum of 2 hours for dispersion.
§Use only original spare parts if you have to repair the kit or the
ready-built module.
Fire risk
Touching flammable material with a hot soldering iron can cause fire,
which can result in injury or death through burns or suffocation.
Connect your soldering iron or soldering station only when actually
needed. Always keep the soldering iron away from inflammable
materials. Use a suitable soldering iron stand. Never leave a hot
soldering iron or station unattended.
Thermal danger
A hot soldering iron or liquid solder accidentally touching your skin can
cause skin burns. As a precaution:
§use a heat-resistant mat during soldering,
§always put the hot soldering iron in the soldering iron stand,
§point the soldering iron tip carefully when soldering, and
§remove liquid solder with a thick wet rag or wet sponge from the
soldering tip.
English S88-3
Page 22
Dangerous environments
A working area that is too small or cramped is unsuitable and can cause
accidents, fires and injury. Prevent this by working in a clean, dry room
with enough freedom of movement.
Other dangers
Children can cause any of the accidents mentioned above because they
are inattentive and not responsible enough. Children under the age of 14
should not be allowed to work with this kit or the ready-built module.
Little children can swallow small components with sharp edges, with
fatal results! Do not allow components to reach small children.
In schools, training centres, clubs and workshops, assembly must be
supervised by qualified personnel.
In industrial institutions, health and safety regulations applying to
electronic work must be adhered to.
S88-3 English
Page 23
!
3. Safe and correct soldering
Caution:
Incorrect soldering can cause dangers through fires and heat. Avoid
these dangers by reading and following the directions given in the
chapter Safety instructions.
§Use a small soldering iron with max. 30 Watt. Keep the soldering tip
clean so the heat of the soldering iron is applied to the solder point
effectively.
§Only use electronic tin solder with flux.
§When soldering electronic circuits never use soldering-water or
soldering grease. They contain acids that can corrode components
and copper tracks.
§Solder quickly: holding the iron on the joints longer than necessary
can destroy components and can damage copper tracks or
soldering eyes.
§Observe correct polarity orientation of semi-conductors, LEDs
electrolytic capacitors and integrated circuits before soldering and
ensure that the solder time does not exceed 5 seconds, otherwise
components can be damaged.
§Apply the soldering tip to the soldering spot in such a way that the part
and the soldering eye are heated at the same time. Simultaneously add
solder (not too much). As soon as the solder becomes liquid take it
away. Hold the soldering tip at the spot for a few seconds so that the
solder flows into the joint, then remove the soldering iron.
§Do not move the component for about 5 seconds after soldering.
§To make a good soldering joint you must use a clean and
unoxidised soldering tip. Clean the soldering tip with a damp piece
of cloth, a damp sponge or a piece of silicon cloth.
§Cut the wires after soldering directly above the PCB solder side with
a side cutter.
English S88-3
Page 24
§After placing the parts, please double check for correct polarity.
Check the PCB tracks for solder bridges and short circuits created
by accident. This would cause faulty operation or, in the worst
case, damage. You can remove excess solder by putting a clean
soldering tip on the spot. The solder will become liquid again and
flow from the soldering spot to the soldering tip.
4. Operation overview
The module is compatible with all components working with the s88-
bus developed by the company Märklin**. It can read in 16 earthed
contacts. This information is transferred via the s88-bus to the next
module or to the connected digital unit (interface, memory or central
unit). The data transfer from one feedback module to the next one
works on the principle of the bucket brigade device.
To each memory unit of Märklin* can be connected in series up to three
and to an interface unit up to 31 feed back modules. If connected
directly to the central unit up to 52 feed back modules can be
connected depending on the type of central unit.
Standard s88-N
The S88-3 has RJ-45 connections according to the standard s88-N,
which regulates the assignment of commercial Ethernet patch-cables
for use in s88 feedback systems. Unlike the 6-conductor connecting
cables frequently used so far, the patch-cables used in computer
networks are screened against outside electric signals. Thus using
patch-cables reduces the liability to interference considerably.
For the connection of digital devices or customary feedback modules
the module has an additional connector for a 6-conductor connecting
cable. Alternatively, the module´s RJ45 connector can be connected to
a 6-pole connector of digital devices or customary feedback modules via
a special adapter (optional extra).
S88-3 English
Page 25
5. Technical specifications
Number of contacts 16
Protected to IP 00
Ambient temperature in use 0 - + 60 °C
Ambient temperature in storage -10 - + 80 °C
Comparative humidity allowed max. 85 %
Dimensions approx. 73 x 83 mm
Weight approx. 71 g
6. Assembling the S88-3
You can skip this part if you have purchased a ready-built module.
Preparation
Put the sorted components in front of you on your workbench. The
separate electronic components have the following special features you
should take into account to prevent mistakes in assembling:
Resistors
Resistors reduce current. Their mounting orientation is of no
importance. The value of resistors for smaller power ratings
(under 5 W) is indicated through colour rings. Every colour
stands for another figure. The colour ring in brackets indicates
the tolerance of the resistor which here is of no importance.
Value Colour rings
1 kΩbrown - black - red (gold)
4,7 kΩyellow - violet - red (gold)
100 kΩbrown - black - yellow (gold)
Andere Handbücher für S88-3
1
Dieses Handbuch passt für folgende Modelle
3
Inhaltsverzeichnis
Andere tams elektronik Steuereinheit Handbücher
tams elektronik
tams elektronik PZS-2 Series Bedienungsanleitung
tams elektronik
tams elektronik 53-02015 Bedienungsanleitung
tams elektronik
tams elektronik HADES Bedienungsanleitung
tams elektronik
tams elektronik LED Control Basic Bedienungsanleitung
tams elektronik
tams elektronik mc2 EasyControl Digital System Silver... Bedienungsanleitung
tams elektronik
tams elektronik S88-6 Bedienungsanleitung
tams elektronik
tams elektronik ABC-1 Bedienungsanleitung
tams elektronik
tams elektronik PZS-3 Bedienungsanleitung
tams elektronik
tams elektronik KSM-4 Bedienungsanleitung
tams elektronik
tams elektronik S88-4 Bedienungsanleitung
tams elektronik
tams elektronik S88-2 Bedienungsanleitung
tams elektronik
tams elektronik HELIOS Bedienungsanleitung
tams elektronik
tams elektronik S88-3 Bedienungsanleitung
tams elektronik
tams elektronik HELIOS.DC Bedienungsanleitung
tams elektronik
tams elektronik KSM-2 Bedienungsanleitung
tams elektronik
tams elektronik mc2 40-03007 Bedienungsanleitung
Beliebte Steuereinheit Handbücher anderer Marken
Festo
Festo Compact Performance CP-FB6-E Stücklistenhandbuch
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung
JS Automation
JS Automation MPC3034A Bedienungsanleitung
JAUDT
JAUDT SW GII 6406 Series Kurzanleitung
Spektrum
Spektrum Air Module System Bedienungsanleitung
BOC Edwards
BOC Edwards Q Series Bedienungsanleitung
