TANDBERG MSE 8350 Bedienungsanleitung

Codian IP Gateway

MSE 8350

Getting started

Codian IP Gateway

MSE 8350

Getting started

may not be copied, photocopied, translated, reproduced, or converted into any

electronic or machine-readable form in whole or in part without prior written

approval of TANDBERG.

TANDBERG reserves the right to revise this documentation and to make changes in

content from time to time without obligation on the part of TANDBERG to provide

notification of such revision or change.

TANDBERG provides this documentation without warranty, term, or condition of

any kind, either implied or expressed, including, but not limited to, the implied

warranties, terms or conditions of merchantability, satisfactory quality, and fitness

for a particular purpose. TANDBERG may make improvements or changes to the

product(s) and/or the program(s) described in this documentation at any time.

All other product and company names herein may be trademarks of their respective

owners.

61-0018-04 rev 01

TANDBERG

Philip Pedersens vei 20

1366 Lysaker

Norway

Telephone: +47 67 125 125

Telefax: +47 67 125 234

Video: +47 67 117 777

E-mail: tandberg@tandberg.com

www.tandberg.com

Table of contents

General information ................................................................................................................ 1

About the MSE 8350 IP GW blade ......................................................................... 1

Port and LED location ................................................................................................ 1

LED behavior ................................................................................................................ 2

Installing the IP GW blade .....................................................................................................4

Step one: Install the IP GW blade into the MSE 8000 chassis ...................... 4

Step two: Connect to Ethernet Ports A and B ................................................... 6

Initial configuration ................................................................................................................. 7

Step one: Configure Ethernet Ports A and B ..................................................... 7

Step two: Configure the default gateway and routes (optional) ............... 7

Configuring the IP GW blade ................................................................................................ 8

Step one: Log in to the IP GW blade .................................................................... 8

Step two: Configure an H.323 gatekeeper or SIP registrar (optional) ...... 8

Step three: Configure the auto attendant menus (optional) ...................... 9

Step four: Configure an operator (optional) ..................................................... 9

Step five: Add endpoints and call groups (optional) ...................................10

Step six: Configure the dial plan ..........................................................................10

Checking for updates ............................................................................................................11

Troubleshooting and technical support information ...............................................12

Using the event log to help solve a problem ..................................................12

Getting more help ....................................................................................................12

General information

About the MSE 8350 IP GW blade

The MSE 8350 IP GW blade fits into an MSE 8000 chassis. The IP GW blade is a

voice and video gateway that allows calls to be made between pairs of IP endpoints

that cannot normally connect directly to each other. A second Ethernet port allows

for connections between two completely independent networks of endpoints. A

built-in auto attendant and support for manual operators allow easy connection of

calls where the endpoint cannot directly address the destination endpoint. The

IP GW blade translates call signalling (for example, between SIP and H.323) and can

connect between almost any two endpoints. The IP GW blade can transcode all

media to ensure the call takes place.

Port and LED location

Figure 1 shows the position of ports and LEDs on the IP GW blade.

Figure 1: IP GW blade front panel

Compact Flash

Activity LED

System Load

Alarm LED

Console Port

Console

Link LED

LEDs

Ethernet Ports

Ethernet Port

Status LEDs

Status LED

Power LED

LED behavior

Table 1 describes the behavior of the LEDs.

Table 1: IP GW blade LED behavior

LED Color Indicates

Compact Flash Activity Flashing

green

One of:

the IP GW blade is booting

a configuration change has been made

the configuration is being transferred

by FTP

Console Link Green A PC is connected to the console port

Status Green The IP GW blade is operating normally

Alarm Red The IP GW blade is booting or has

developed a fault, for example:

temperature is outside normal limits

battery failure of the internal clock

Refer to the web interface for more

information about the problem (go to

Status > Health)

System Load Green The IP GW blade is processing data. The

LEDs represent the media processing load

of the IP GW blade. The column

numbered 1 represents audio load. The

other columns represent video DSP load.

Media processing load is also displayed in

the web interface: go to Status > General

to see the percentage load

General information

Ethernet Port Status, for each

Ethernet port:

FDX Green The link has been negotiated as a full-

duplex link

Act Green Packets are being transmitted on this port

Link Green The speed of the link from this port,

which is either 10, 100, or 1000 Mbps

Power Blue The IP GW blade is receiving power from

the MSE 8000 chassis

Table 1: IP GW blade LED behavior (continued)

LED Color Indicates

Installing the IP GW blade

For information about powering the MSE 8000, refer to the Getting Started Guide

that accompanied the chassis.

Step one: Install the IP GW blade into the MSE 8000 chassis

1 Remove the blade or blanking blade from the slot into which you are going to

install the IP GW blade:

i Using a No.1 Phillips screwdriver, loosen the screws in the retaining latches

with an anti-clockwise quarter turn.

ii Open both retaining latches on the front of the blade or blanking blade.

When open, a retaining latch is at a 90° angle perpendicular to the front of

the blade.

iii Slide out the blade or blanking blade.

2 Open both retaining latches on the front of the IP GW blade. When open, a

retaining latch is at a 90° angle perpendicular to the front of the blade.

3 Slide the IP GW blade into the blade slot (as shown in Figure 2) until it stops.

4 Simultaneously close both retaining latches on the blade (thereby engaging the

connectors at the rear of the blade) to secure in the chassis as shown in Figure 3.

Before installing the IP GW blade into the MSE 8000, read the Safety

Information guide that accompanied the MSE 8000 chassis.

Although blades are hot-swappable parts, you must only remove one

blade at any time. Remove the power from the MSE 8000, if you need to

remove more than one blade at a time.

Before hot-swapping a blade, shut down the blade using the web interface.

Do not shut down a blade during a software upgrade or if the blade is

processing (for example if a call is taking place).

You must install either a blade or a blanking blade in each of the ten

positions in the chassis.

The Supervisor blade must be installed into slot 1 of the MSE 8000

chassis.

Installing the IP GW blade

5 Using a No.1 Phillips screwdriver, tighten the screws in the retaining latches

with a clockwise quarter turn.

Figure 2: Inserting a blade into the chassis

Figure 3: Closing the retaining latches on the front of a blade

Step two: Connect to Ethernet Ports A and B

Connect an Ethernet cable from Ethernet Port A to an Ethernet switch (rather than a

hub, to minimize interference from other devices on the network). The Ethernet

port is a 10/100/1000 Mbps auto-sensing connection.

Connect Port A to your local network and connect Port B to a second subnet or the

internet depending on your application of the IP GW blade.

Do not connect Ethernet Port A and Ethernet Port B to the same subnet.

Inhaltsverzeichnis

Andere TANDBERG Tor Handbücher

TANDBERG

TANDBERG Codian GW 3201 Series Bedienungsanleitung

TANDBERG

TANDBERG Gateway Bedienungsanleitung

TANDBERG

TANDBERG D1320203 Bedienungsanleitung

TANDBERG

TANDBERG IP GW 3500 Series Bedienungsanleitung

TANDBERG

TANDBERG 3G GATEWAY 1 Bedienungsanleitung

TANDBERG

TANDBERG D13192 Stücklistenhandbuch

TANDBERG

TANDBERG D13187-03 Bedienungsanleitung

TANDBERG

TANDBERG 3G GATEWAY 1 Bedienungsanleitung

TANDBERG

TANDBERG MPS 800 Bedienungsanleitung

TANDBERG

TANDBERG GW Bedienungsanleitung

TANDBERG

TANDBERG Codian MSE 8321 Bedienungsanleitung

TANDBERG

TANDBERG D13841.08 Service-Handbuch

TANDBERG

TANDBERG MPS 800 Bedienungsanleitung

Beliebte Tor Handbücher anderer Marken

LST

LST M500RFE-AS Bedienungsanleitung

Kinnex

Kinnex Media Gateway Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace 2N StarGate Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Bedienungsanleitung

Telsey

Telsey CPVA 500 - SIP Bedienungsanleitung

RTA

RTA 460A-NNA4 Technisches Datenblatt

Shaw

Shaw Gateway HDPVR Bedienungsanleitung

ABB

ABB VSN900 Kurzanleitung

Commander

Commander Pulse Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Bedienungsanleitung

NETGEAR

NETGEAR C6300BD Bedienungsanleitung

Amit

Amit CDW531AM Bedienungsanleitung

HMS

HMS Netbiter EasyConnect EC150 Bedienungsanleitung

Huawei

Huawei EchoLife HG620 Bedienungsanleitung

AT&T

AT&T U-verse 3801 Gebrauchs- und Pflegehandbuch

Logic IO

Logic IO RTCU MX2 turbo Bedienungsanleitung

Suttle

Suttle MediaMAX MXM-521 Bedienungsanleitung