TANDBERG LTO HH Bedienungsanleitung

Revision 6 – August 2007

Tandberg

TandbergTandberg

Tandberg LTO HH

LTO HH LTO HH

LTO HH

LTO

LTOLTO

LTO-

-1, LTO

1, LTO1, LTO

1, LTO-

-2, LTO

2, LTO2, LTO

2, LTO-

-3

(220LTO, 420LTO, 820LTO)

Tape Drive

Quick Installation Guide

Mechanical Installation Internal Tape Drive

For mechanical mounting specifications, please refer to Figure 1.

Allowed mounting position is either horizontal with the indicator LEDs to the

right, or vertical with the LEDs up.

The drive occupies a half-size 5.25-inch slot with standard holes for mounting

screws on both sides of the drive chassis and at the bottom of the drive.

Figure 1 Mounting specifications

Important!

Mounting screw

requirements

•Only M3 (metric) screws must be used for mounting the drive

•Maximum permitted screw penetration: 2.5 mm

•Minimum required screw penetration: 2.0 mm

•Screw torque, mounting screws: 0.5 Nm

•Screws are supplied with all the Tandberg 220/420/820LTO drive

variants

•Bags with 4 screws and 4 SCSI ID jumpers are available

(Ordering no. 43 32 65)

Do not use longer screws or higher screw torque than specified!

Figure 2 Allowed mounting orientations

SCSI Identification on Internal Tape Drive

Make sure that the drive unit has the proper SCSI-ID before it is connected to a

computer system. Refer to manuals for host computer and application software to

obtain the correct ID.

For correct mounting of ID-jumpers at the rear of the internal drive, please refer to

Figure 3 and Table 1 for internal tape drive.

Figure 3 Drive connectors

The factory default drive

number setting is SCSI ID = 2.

If the drive has to be set up

with a different unit number,

the jumpers (on the Service

Connector) have to be

connected according to

Table 1.

Example: SCSI ID = 2

Table 1

Service Connector jumper settings for SCSI

ID (Dark = Jumper mounted)

Power Connector

SCSI Connector

Service Connector

SCSI ID=0

SCSI ID=1

SCS

I ID=2

Default

SCSI ID=3

SCSI ID=4

SCSI ID=5

SCSI ID=6

SCSI ID=7

SCSI ID=8

SCSI ID=9

SCSI ID=10

SCSI ID=11

SCSI ID=12

SCSI ID=13

SCSI ID=14

SCSI ID=15

Termination Internal Tape Drive

The Internal SCSI-bus cable must be terminated as shown in Figure 4 according to

SCSI specifications. If the tape drive is the last device on the bus, the bus must be

terminated within 10 cm of the tape drive connection.

Tandberg LTO-1, LTO-2, LTO-3 have a combined SCSI-LVD/SE interface

embedded. The PC-98 Specification specifies that the termination of the SCSI-bus

system is a part of the SCSI-cable and not a part of the SCSI-device. As a result,

termination cannot be turned on or off directly on the tape drive itself.

For internal devices, a SCSI-cable with an integrated terminator or a separate

terminator applied to the end connector of the cable, 10 cm from the last device,

must be used.

Figure 4 Internal SCSI cable and termination

External Tabletop Enclosure

For front view, please see the picture on the front page.

Figure 5 External tabletop enclosure, rear side

SCSI Identification on External Tabletop

Make sure that the drive unit has the proper SCSI-ID before it is connected to a

computer system. Refer to manuals for host computer and application software to

obtain the correct ID.

External Tabletop Enclosures have a thumb-wheel switch to set the SCSI-ID for

the tape drive (see Figure 5).

Host

Last SCSI Device

Internal Terminator Connector

SCSI

bus

10 cm

Cooling Fan

SCSI_ID Switch

SCSI Interface Connectors

Power Connector

ON/OFF Switch

Termination External Tape Drive

External devices must be terminated with an external terminator on the last device

on the SCSI-bus. Please see Figure 5 for SCSI connectors and Figure 6 for SCSI

termination.

Figure 6 External SCSI cabling and termination

SCSI Cables Ordering no.

•Internal SCSI-LVD/SE-cable with 5 connectors (Ordering no. 43 20 51)

•Internal, removable SCSI-LVD/SE-terminator (Ordering no. 43 20 53)

•External, removable SCSI-LVD/SE-terminator (Ordering no. 43 26 17)

•External SCSI 68HD/VHDCI 320MBs-cable (Ordering no. 43 32 64)

External terminator on the last device

on the SCSI bus

SCSI Interface adapter

Front LED Indicators

Figure 7 Light Emitting Diodes (LED)

Drive State READY LED

(Green left)

ACTIVITY LED

(Green)

CLEAN LED

(Amber)

FAULT LED

(Amber right)

LED-test.

The LEDs are turned N one-by-one.

Power- n Self-Test starts in parallel

with the LED-test .

N N N N

Cartridge not loaded. FF FF N / FF FF

Cartridge loaded, no activity N FF N / FF FF

Cartridge loaded, activity N Flashing N / FF FF

Cleaning FF Flashing N FF

Cartridge loading or unloading FF Flashing N / FF FF

Unrecoverable drive failure N / FF FF N / FF Flashing

ver temperature FF FF N / FF N

Media Error (wrong, write protected or

harmed media) FF Flashing N / FF Flashing

Table 2 Front LED behavior during normal operation

Software Installation

For Software Application support and software drivers, please see

www.tandbergdata.com. Then select SUPPORT and Select Product.

For installation of Backup Application software, refer to the software vendor’s

software application user guide supplied with the software or on the software

vendor’s web.

Media and Capacities

To achieve and maintain the maximum quality of your Tandberg Data tape drive,

we recommend using Tandberg Data media.

Drive

odel

edia Name Tape

Length

Capacity

(Native)

Ordering

no.

LT -1 LT Ultrium Generation 1 (Native format) 609 m 100 GByte 43 26 30

LT -2 LT Ultrium Generation 2 (Native format)

LT Ultrium Generation 1 (Read/Write compatible)

609 m

200 GByte

100 GByte

43 27 44

43 26 30

LT -3 LT Ultrium Generation 3 (Native format)

LT Ultrium Generation 2 (Read/Write compatible)

LT Ultrium Generation 1 (Read compatible)

680m

609 m

400 GByte

200 GByte

100 GByte

43 32 16

43 27 44

43 26 30

LT 1, 2, 3 Cleaning Cartridge for LT 1, LT 2 and LT 3 43 26 31

Table 3 Media alternatives

Power Requirements

Tandberg LTO-1, LTO-2, LTO-3 in external tabletop enclosure:

AC Input: 100 VAC / 0.6 A or 240 VAC / 0.3 A, 50-60 Hz

Tandberg LTO as standalone: LTO-1/LTO-2 LTO-3

DC Input (typical operation) 5 VDC 2.1 A 0.8 A

DC Input (typical operation) 12 VDC 0.6 A 0.7 A

Heat Dissipation

Tandberg LTO as standalone: LTO-1/LTO-2 LTO-3

Operating: 18 W 13 W

Sleep mode with cartridge inserted: 9 W 6 W

Tandberg Data

Tandberg DataTandberg Data

Tandberg Data

Total customer satisfaction is of the utmost importance

to Tandberg Data.

We guarantee that this product left our premises defect free.

If you are not satisfied with the quality of this product,

please contact your distributor or the nearest

Tandberg Data office to have the problem solved!

For more documentation and information, please see our website

www.tandbergdata.com.

International headquarter

Tandberg Data ASA, Oslo, Norway.

Please visit our web site for detailed address

www.tandbergdata.com

Worldwide subsidiaries

Tandberg Data Corp., 2108 55th Street, Boulder CO 80301 USA

Tel. Toll Free: +1 800-392-2983. Tel. Local: (303) 442-4333

Tandberg Data GmbH, Feldstrasse 81, D-44141 Dortmund, Germany.

Tel: +49 231 5436 0. Fax: +49 231 5436 111.

Tandberg Data S.A.S., 16/18 Ave. Morane-Saulnier, F-78941 Vélizy Cedex, France.

Tel: +33 1 39 26 01 01/00800-82632374.

Fax: +33 1 34 65 02 89 (for technical support: 00800-07867243).

Tandberg Data (Asia) Pte. Ltd, 20 Bendemeer Road, #04-05 Cyberhub, Singapore 339914,

Tel: +65 6396 0786. Fax: +65 6396 0787.

Tandberg Data (Japan) Inc., Eitaibashi Eco-Piazza Bldg. 8th floor 29-13, Shinkawa 1-chome,

Chuo-ku Tokyo 104-033, Japan

Tel: +81 3 5566 2871. Fax: +81 3 5566 2875.

Tandberg Data Ltd., Bloxham Mill Business Centre, Barford Road, Bloxham, Banbury,

Oxfordshire, OX15 4FF, United Kingdom

Tel: +44 (0) 8450706916.

Specifications subject to change without notice. All trademarks are the property of their respective owners.

Part No. 433261-06. August 2007.

Inhaltsverzeichnis

Andere TANDBERG Lagerung Handbücher

TANDBERG

TANDBERG 420LTO Bedienungsanleitung

TANDBERG

TANDBERG STORAGELIBRARY Bedienungsanleitung

TANDBERG

TANDBERG VXA TAPE DRIVE Bedienungsanleitung

TANDBERG

TANDBERG LTO3 Bedienungsanleitung

TANDBERG

TANDBERG 220-420LTO Bedienungsanleitung

TANDBERG

TANDBERG SDLT600 Produktinformationsblatt

TANDBERG

TANDBERG SLR7 Bedienungsanleitung

TANDBERG

TANDBERG 840LTO Bedienungsanleitung

Beliebte Lagerung Handbücher anderer Marken

QNAP

QNAP TS 32PXU Series Bedienungsanleitung

LaCie

LaCie RUGGED RAID Bedienungsanleitung

Freecom

Freecom CLS DOCK Bedienungsanleitung

PNY

PNY Attache P-FD64MBATT3 Bedienungsanleitung

HP StorageWorks MSL2024 Bedienungsanleitung

OLT

OLT 6x6 Maximizer Bedienungsanleitung

Transcend

Transcend JetFlash 160 Bedienungsanleitung

LaCie

LaCie RUGGED MINI Bedienungsanleitung

Thunderbolt

Thunderbolt 600 Bedienungsanleitung

Panasonic

Panasonic LB-DH8 series Handbuch

Intel

Intel RAID High Availability Bedienungsanleitung

LaCie

LaCie 12big Thunderbolt 3 Bedienungsanleitung

Spectra Logic

Spectra Logic T-Series Spectra T50e Bedienungsanleitung

Panasonic

Panasonic LKM-F931-1 Bedienungsanleitung

Tabernus

Tabernus Enterprise Erase E2400 Bedienungsanleitung

Rocstor

Rocstor COMMANDER 3F series Bedienungsanleitung

Western Digital

Western Digital Ultrastar Data60 Bedienungsanleitung

HP P9000 Bedienungsanleitung