Taramp's TMA Freedom 200 Bedienungsanleitung

MANUAL

TMA FREEDOM 200

2) Technical Features

Supply voltage

Consumption

Engine lock

Turn indicators outputs

Siren output

9 to 18 Volts

Max. 20 A

2 x 4A

Only use the dedicated siren

Replacing the control battery.

3) 3) Remote Controls*

•This product aims to prevent or inhibit the theft of the motorcycle.

•Before contacting the TARAMPS technical support, read this manual, it contains all

information necessary for installation and use.

•The installation should be performed by a trained operator / technician.

•During installation, only use a multimeter to measure the voltage.

•For perfect operation, the ignition signal must be connected to the alarm. Always use

TARAMPS dedicated siren!

•Clean the place where the alarm will be ﬁxed to ensure good adhesion. Keep it away from the

ignition module, spark plug and ignition coil.

•During installation make sure that the control unit is properly attached to and away from metal

parts. This may degrade the reception of the remote control signal, causing false shots when

using the presence function.

•The TMA Freedom module has a tilt sensor. It does not require any adjustment.

433.92 MHz Operation frequency

Anti-Cloning Technology (Hopping Code)

1 CR 2032 3V-LITHIUM Battery

1) Before you begin

Control

PRESENSE

TR2-P

Control

TR2

BUTTONS

ARM DISARM AUXILIARY

HOME

Open the plastic box carefully, from

the sidelines. Replace the battery,

observing the polarity (+) e (-).

Use Cr2032 battery.

USE GOOD

QUALITY BATTERY

* See item 10 which remote control belongs to which

Alarm model. Any control model can be purchased

separately.

ATTENTION: We recommend reading this manual before installation!

Illustrative images, can diﬀer from actual models.

Sleep = 0,3mA / Normal = 5mA

Auxiliar output Max. 200mA

4) Remote Control Functions

FUNCTION ALARM RESPONSE

Note: If you hear four fast siren chirps

and turn lights blinks 4 times, it

indicates that was a triggering when

the alarm was armed .Item 7.2

Turn lights ﬂash once beep siren.

While the button is pressed, the alarm

generates a negative signal.

Operation depends on how the

ins t all a t io n w a s c o n ﬁg u r ed .

Installation of modules or relays is

required. Item 7.4

Turn lights ﬂash twice

For the siren and turn lights ﬂash. The

alarm still remain active.

The alarm will turn oﬀ. Item 8

Programmable function, Item 11.11

The siren will beep according to the

triggering causes(ignition, tilt sensor

and / or auxiliary input).

In the next arm, back to work.

Turn lights ﬂash for 40 seconds. To

cancel, press the

See item 7.5

Turn lights ﬂash twice siren beeps

twice.

The alarm will turn on. Item 8

Programmable function, Item 11.11

Turn lights ﬂash once

Note: If you hear four fast siren chirps

and turn lights blinks 4 times, it

indicates that was a triggering when

the alarm was armed .Item 7.2

The siren sounds and turn lights ﬂash

for 40 seconds. To stop, press

1 long beep, cancels the inclination

sensor.

Item 7.2

Press

Move the TR2-P control

far away from motorcycle

Press then

Press with the alarm

triggered

Move the TR2-P control

to be close from

motorcycle,Item 8.1

Press for 2 seconds

with the alarm disarmed

Press shortly

thereafter by 2 seconds

Press for 2 seconds

with the alarm on

Press for 2 seconds

with the alarm on

After a trigger caused by

any sensor, disarm the

alarm and press

Press

4.1 Arm the Alarm

4.2 Disarm the Alarm

4.7 To locate

motorcycle

4.12 Triggering report:

see the reason for the

last triggering

4.13 HOME

4.4 Disarm the alarm

by presence

4.3 Arm the alarm by

presence

4.8 Panic

4.6 Disarm alarm no

beep

4.11 Auxiliary Output

4.5 Arm alarm no beep

4.10 Tilt Sensor

4.9 Stop triggering

alarm

ACTION IN CONTROL

INSTALLER: You can only use one Anti Carjacking type at a time, by

presence, or by Secret Button. Inform the user to use the ignition key . item 12

Only It can disable the alarm when the remote control is lost.

5) Types of Anti Carjacking (enable the secret button)

5.2 ANTI CARJACKING BY PRESENCE:

Pressing the Secret Button at any time will cancel the function.

5.1.1VALET FUNCTION: Is used to leave the motorcycle in a parking lot; for

example: without the need to indicate to the Valet the secret button position. Turn oﬀ

the ignition, hold the secret button pressed for 3 seconds, turn ligths blinks 3x, will

conﬁrm the activation. To cancel, press the secret button for 1 second with the

ignition on.

Enable the function in the control module , ignition switched on, moving item 11.5

the PRESENCE control away from the motorcycle, anti carjaking function is

activated. After the time programmed for lock, short or long , the turn item 11.9

lights and the siren will sound. After another 20 seconds, the engine starts to fail

until it is permanently blocked.

To cancel, close the TR2-P control of the motorcycle and wait for the

transmission or press the OFF button on the TR2-P control.

5.1 ANTI CARJACKING by SECRET BUTTON: With the function enabled in the

control module, every time the ignition is switched on, the Secret Button item 11.6

must be pressed for 1 second, otherwise it will activate the carjacking function. After

the time programmed for lock, short or long , the turn lights and the siren item 11.9

will sound. After 20 seconds, the engine starts to fail until it is permanently blocked.

ATTENTION: Only the PRESENCE control can cancel the Anti Carjacking

by Presence. If the remote control is lost, turn oﬀ the alarm by the ignition

password until a new control is recorded for the cancel this function, item

11.3.

It is necessary to replace the battery of the control every 6 months or when the

alarm gives 1 beep when turning the ignition on, informing that the control

battery is low item 7.6.

The PRESENCE control must be in contact with the rider, separated from the

key and not close to metallic objects such as coins or cell phones, this may

cause interference into transmission.

ATENTION: Function canceled in the DEFAULT settings. It is necessary to

enable the Automatic Transmission of the TR2-P control and to item 6.1

enable the anti carjaking by Presence in the alarm central. item 11.5

TR2-P

6) Presence function -TR2-P control

6.2 DISABLING THE PRESENCE MODE IN THE TR2-P CONTROL:

Press the buttons simultaneously until the LED turns oﬀ and blinks 2x.

2) Check if the transmission of the presence signal to keep is enabled; item 6.1

3) Keep the ignition oﬀ;

4) Hold the buttons pressed until the LED turns oﬀ and ﬂashes (1) blink. Do this near

the motorcycle (as would be the real situation).

Every 2 seconds, the control will transmit the presence signal. The alarm will sound (1) beep

Every time when it receives the signal from the control.

*THESE FUNCTIONS DEPEND ON THE ANTI CARJACKING BY PRESENCE -

ENABLED 1ST. BEEP. ITEM 11.5

6.3 PRESENCE TEST:

To avoid the alarm triggering when the motocycle is running, activate the transmission again.

This function allows to do the blocking test without need the remote control far away from the

motocycle.

To exit the function, press any button of the TR2-P control.

1) Enables anti carjacking by presence; item 11.5

6.1 ENABLING PRESENCE MODE IN THE TR2-P CONTROL:

Press the buttons simultaneously until the LED turns oﬀ and blinks 1x.

Then the presence signal will be transmitted every 30 seconds.

TRANSMISSION IS DISABLED AS DEFAULT.

ACTIVATE

TRANSMISSION:

PRESS SIMULTANEOUSLY:

Until the LED

turns oﬀ and blinks 1x.

DISABLE

TRANSMISSION:

PRESS SIMULTANEOUSLY:

Until the LED

turns oﬀ and blinks 2x.

7) Alarm Functions

Turning the ignition on or moving the motorcycle (with the tilt sensor active) will

back the system to normal, thereby powering the RF system. Turn oﬀ the alarm by

the remote control as soon as the turn lights start blinking. Otherwise, after 10

seconds the alarm will trigger siren, turn lights and lock the engine. The alarm can

also be turned oﬀ by the ignition key .item 12

7.3.2 VIOLATION OF THE TILT SENSOR IN SLEEP MODE NEED AN ACTION.

7.1 SHUTDOWN-LIMITATION OF ALARM TRIGGERS: In case of violation, the

alarm will trigger the siren and ﬂash turn light for 45 seconds. After 5 seconds, the

sensors will be monitored. If it is triggered 4 times by the same sensor, this will be

disabled, keeping the other ones active. It will only be monitored again when

7.2 ALARM TRIGGER REPORT: When you disarm the alarm and hear 4 beeps, it

means that the alarm was triggered. To identify the cause, press the button on any

control, BEFORE the next arm. The number of siren beeps indicates the trigger

motive, as shown in the table below:

1 beep - Tilt Sensor - Accelerometer

2 beeps - Auxiliary sensor

7.3 SLEEP FUNCTION (motorcycle battery saving)

Exclusive for the TARAMPS Alarm. Function enabled by defaut. item 11.10

3 beeps - Ignition

the alarm is armed again by the remote control.

When the alarm is turned on by the remote control, after 24 hours, the system enters

Sleep mode. In this mode, motorcycle battery consumption is 17 times lower than in

normal mode. All sensors remain operative, triggering the alarm at any violation

attempt. However, for, the RF (Remote Control Receiving System) system is

temporarily turned oﬀ, so the alarm center does not respond to remote control

commands.

7.3.1 HOW TO DISARM THE ALARM WHEN IN SLEEP MODE?

The tilt sensor is not violated by simply changing the position of the motorcycle. It

will, such as sitting on the seat of the motorcycle, to exit the Sleep mode. After

that, the turn lights will turn on for a few seconds and blink fast. Press the disarm

button on the remote control.

7.4 AUXILIARY OUTPUT - Gray Wire

Output with negative signal enabled by the AUXILIARY button on the remote

control.

By the HOME button of the TR2 and TR2-P controls, it is possible to activate the

automatic gates or home alarm, without the needing of an auxiliary module, only

learning the control in the control panel.

The TR2 or TR2-P control must be rconﬁgured according to the home alarm or gate

manufacturer's instructions, .

Compatible with CODE LEARNING systems.

7.5 HOME function of the control TR2 and TR2-P:

When installing to start the motorcycle engine, it will be necessary to use auxiliary

module and connect the Green wire to the negative signal of the gear neutral

sensor to identify that it is neutral, in other cases connect the Green wire to the

GND.

7.6 LOW BATTERY WARNING TR2-P: When the ignition is turned on, a long

beep is given if the alarm has detected a low-battery remote control. This feature

works only for the control TR2-P, control with presence function.

If the presence function is enabled in the remote control, the battery consumption

will be faster. In order to continue working, it is important to pay attention to the

warnings and replace the battery when needed. Always use good quality battery

(Tip: use the same brand as in the control).

8) On / Oﬀ by Presence Function

When you move it away, the alarm will be activated automatically after a few minutes without

siren beep and or blinking turn lights.

If the ignition is switched on or the motorcycle is moved before receiving the presence signal,

the turn lights will ﬂash for 40 seconds (siren will not sound). To turn it oﬀ, press the Control Oﬀ

button or wait until the control sends the presence signal. The 'Oﬀ by Approach' function will

only work if the alarm has been armed by moving away from the Presence control.

The TR2-P control emits a signal that is received by the central alarm when it is close to the

motorcycle. This function (programmable - ) allows the user to turn on the alarm Item 10.11

simply by moving the remote control away from the motorcycle.

The alarm may take up to 30 seconds to disarm when moving closer the remote control TR2-P

to the motorcycle.

Only the TR2-P control supports this feature. To work properly, the automatic transmission

must be activated, .Item 6.1

For perfect operation, securely ﬁx the control unit in the motocycle body.

NOTE: The control unit can be ﬁxed at any angle.

The TARAMPS TMA Freedom alarm has an accelerometer in the control unit, which check

and store the tilt of the motorcycle when turned on by the remote control when it is changed,

triggers the alarm.

9) Tilt Sensor

Control

TR3C

12) What is included LINE G3

Control

TR1 PRESENSE

Control

TR1-P

Control

TR2 PRESENSE

Control

TR2-P

TR3C

Freedom

100 Freedom

200 Dedicado

200

BEEPS FUNCTION FACTORY

DEFAULT RESPONSE WHEN RELEASING

THE MASTER KEY

ENABLE/DISABLE Alarm

11) Programming

Wait for the beep of the desired function, as shown in the table below. Disconnect the Orange /

Black wire to conﬁrm the programming change.

While programming, keep the turn lights oﬀ. After every process, insulate the orange / black

programming wire.

Turn the ignition on, and then connect the Programming wire (Orange / Black) to the + 12V of

the motorcycle battery.

11.

12.

10.

Long

1 beep = Enabled

2 beeps = Disabled

SIREN BEEP, turns on and oﬀ

Item 12

Password 3_3New ignition password

Tilt Sensor

Item 9

Short / Long Lock

4 LONG BEEPS END of SETUP without CHANGES.

= Enabled = Disabled

1 long beep - factory settings

restored

RECORDING CONTROLS.

Up to 4 controls. When writing

th st

the 5 , the 1 will be replaced.

Turn lights + long beep. Press

the buttons arm and disarm

simultaneously in the control,

3 beeps conﬁrm the recording.

1 beep = Enabled

2 beeps = Disabled

ANTI CARJACKING BY PRESENCE

Item 5.2 1 beep = Enabled

2 beeps = Disabled

ANTI CARJACKING BY SECRET BUTTON

Item 5.1 1 beep = Enabled

2 beeps = Disabled

1 beep = Enabled

2 beeps = Disabled

1 beep = Enabled

2 beeps = Disabled

1 beep = Enabled

2 beeps = Disabled

1 beep = Short

2 beeps = Long

1 beep = Enabled

2 beeps = Disabled

FACTORY SETTING

Power On / Oﬀ by Presence

Item 8

Turn lights ﬂash on / oﬀ

Sleep - Battery saving

Item 7.3

12) Ignition Password - Disable Alarm Without Control

How to use:

1- Turn the ignition oﬀ and wait 5 seconds;

Wait 3 seconds;

3- Turn the ignition on and oﬀ according to the second digit number (default 3).

In case of problems with the remote control (low battery, malfunction or loss), it is possible to

disable the alarm by the ignition password even when triggered. With the alarm is disabled, it

won’t work until it is enabled again by the ignition password.

2 beeps: disable.

The alarm will signal after 2 seconds with:

2- Turn the ignition on and oﬀ according to the number of the ﬁrst digit (default 3).

1 beep: enable;

13) Changing the ignition password

Factory password _3_: _3_ NEW PASSWORD ____: ____

3- After the 4 beep, turn oﬀ the Orange / Black wire, the alarm will give 4 beeps and the

turn lights will be lit.

5. Wait 2 seconds (1 siren beep will be heard);

6- Turn the ignition on and oﬀ the number of times the second digit at the end and ignition

oﬀ;

4- Turn ignition on and oﬀ the number of times of the ﬁrst digit;

1- Turn on the ignition;

After a few seconds, a long beep will be heard to conﬁrm the new recorded password. If

you hear 2 beeps, a recording error has occurred. Perform the whole process again.

2- Connect the Orange / Black wire to the + 12V of the motorcycle battery;

12) Installation Diagram

Auxiliary Output

8 e 9 - Green / Black

Dedicated Siren + 12 Vcc

Lighting Indicators

11 - Red

12 - Grey

10 - Grey

6 - Grey

5 - Orange / Black

4 - Orange

Programming

3 - Black

GND

2 - Blue

Ignition

1 - Green

Chest Sensor

Master Key

BLOCK OF THE ENGINE

MÁX. 20A

7 - Black / Yellow

If the battery is under 12V, arrange for recharging or

replacement.

Check that the battery is receiving charge while the

motorcycle is on.

Check the battery voltage with the motorcycle oﬀ. Suporte Técnico

Technical Support / Apoyo Técnico

+55 18-3266-4050 / +55 18 99627-3364

suportetecnicotaramps WhatsApp

Inhaltsverzeichnis

Andere Taramp's Motorradzubehör Handbücher

Taramp's

Taramp's Tarsafe TMA 10 G4 Bedienungsanleitung

Beliebte Motorradzubehör Handbücher anderer Marken

SRC

SRC B-TRK502-01-01-SL Bedienungsanleitung

hepco & becker

hepco & becker 6307520 00 01 Bedienungsanleitung

HOMCOM

HOMCOM AA0-077 Bedienungsanleitung

hepco & becker

hepco & becker 6307558 00 01 Bedienungsanleitung

Wunderkind Custom

Wunderkind Custom 106503-F15 Benutzerhandbuch

Dräger

Dräger HPS 3500 Bedienungsanleitung

M-WAVE

M-WAVE SKI Bedienungsanleitung

Kuryakyn

Kuryakyn 6212 Bedienungsanleitung

hepco & becker

hepco & becker 6507504 00 01 Bedienungsanleitung

Tool it

Tool it PROMAX LCD 9.13G Bedienungsanleitung

Custom Dynamics

Custom Dynamics TruWrapz Bedienungsanleitung

Roof

Roof RO200 CARBON Bedienungsanleitung

Kabuto

Kabuto Japan IBUKI Bedienungsanleitung

PUIG

PUIG 5051 Bedienungsanleitung

rizoma

rizoma ZTH050 Bedienungsanleitung

Joubert

Joubert 10001711 Bedienungsanleitung

SW-Motech

SW-Motech SBL.01.971.10000/B Bedienungsanleitung

GÜDE

GÜDE GSH 180-TC-2 Bedienungsanleitung