Target LaserTrack LT400 Bedienungsanleitung

ENGLISH

TABLE OF CONTENTS

PREFACE 4

AREA OF APPLICATION OF

THE TARGET LASERTRACK 5

CONTENTS OF THE PACKAGE

AND OPTIONAL ACCESSORIES 5

IMPORTANT INFORMATION 6

INSTALLATION 6

TRANSPONDER ALIGNMENT 7

CALCULATION TABLE FOR THE

INSTALLATION OF THE TRANSPONDER 8

TESTING THE OPERATION 9

IMPORTANT INFORMATION

FOR ALL USERS 9

FAQ ABOUT TARGET LASERTRACK 10

INSTALLATION OF THE LT425

CONTROL CIRCUIT BOARD AND

THE LT420 BASIC TRANSPONDER 11

TECHNICAL SPECIFICATIONS 13

CONDITIONS OF GUARANTEE 14

CONNECTION DIAGRAM 88

PREFACE

You have just purchased a TARGET LaserTrack and are now

the owner of a very advanced Class 1 laser remote control

system which can be used for various actions. The system

is unique because it allows you to open your automated

gate, garage door or turn on or off the outdoor lighting

fully automatically, i.e. without pressing a button, at a

distance equal to that of radiographic remote control sys-

tems. The unique code of your vehicle is automatically

recognized by the basic transponder(s) as soon as you are

within range through the patented “trigger and reply”

tech-

nology. The Class 1 laser technology used is safe, reliable

and is more user-friendly than conventional remote

control systems.

The automotive industry has also discovered the advan-

tages of laser technology. Nissan already introduced an

“adaptive cruise control system” which automatically

determines the distance to the cars in front of it and

which adjusts the speed accordingly if required. Laser

technology is also widely applied for distance measuring

systems that can be mounted in the vehicles after these

have left the factory.

We believe our system can increase the comfort of

driving and wish you many happy years using your

TARGET LaserTrack.

We recommend you read this manual thoroughly in

order to get fully acquainted with the system.

Target Automotive BV

ENGLISH

AREA OF APPLICATION OF

THE TARGET LASERTRACK

THE TARGET LASERTRACK IS

DELIVERED IN 3 PACKAGES:

LT 400 Vehicle System

• 1 LT 400 car transponder (refer also to the accessories)

• 1 LED

• 1 Piezo signal device

• 1 Water leveller

• All required connection and fastening material

LT 430 House System

• 1 LT420 basic transponder

• 1 Control circuit board LT425

• 1 Water leveller

• All required connection and fastening material

LT 450 Complete System

• 1 LT 400 car transponder

• 1 LT420 basic transponder

• 1 LT425 control circuit board

• 1 Piezo signal device

• 1 LED

• 1 Water leveller

• All required connection and fastening material

ENGLISH

1. Exterior lighting

2. Access control

3. Garage doors

ACCESSORIES (OPTIONAL)

A special transponder for motorcycles is available.

For motorcycles order the TARGET LT400-M. The control

elements of this set are completely waterproof and

weatherproof. This system also has a special optical sig-

nalling system that is always visible to the motorcyclist.

IMPORTANT INFORMATION

Nearly all laser systems using infrared light emit their

information on a frequency of 904 nanometre (this is the

wave length which emits infrared laser light). This is also

true for the LaserTrack. This wave length has become the

worldwide standard. Even the police laser guns emit

speed measurements on this wave length. TARGET

LaserTrack is the only system that has intelligent elec-

tronic technology that can recognize the signals of laser

guns and other laser systems that use the same wave

length. After recognizing an infrared signal that is not its

own, TARGET LaserTrack temporarily shuts itself off to

prevent failures and, for example, to allow a laser speed

measurement to take place. You are informed of this

through a visual and audio signal.

INSTALLATION

Follow the instructions below to the letter to ensure

that the system performs optimally.

MOUNTING AND CONNECTING

THE LT400 CAR TRANSPONDER

1. Mount the transponder preferably in the middle at the

front of the vehicle (preferably very near to the number

plate). The transponder may also be mounted behind the

grill. The free passage opening should be larger when the

distance from the transponder to the opening is greater.***

Refer to the calculation table on page 8.

2. Mount the transponder using the tee bolt and

mounting bracket included in the package.

(Refer to Transponder Alignment on page 7.)

3. Ensure the transponder is aligned correctly

(refer to Transponder Alignment on page 7).

4. Lead the transponder cable through the engine com-

partment. Use the cable guides already present when

possible. Do not pull the cable too tightly and do not

kink the cable. Lead the cable through the existing grom-

met to the interior. Connect as indicated in the diagram

on page 88.

ENGLISH

CABLE CONNECTION:

LT400 Connect to:

1. Red Switched 12 V from the vehicle (+15).

This is the cable with 12 V as soon as

the vehicle is started. Mount a fuse for

this connection. A switch can be added

to this connection if required.

2. Black Earth. Connect this cable to a good earth

source. Preferably a section of the chassis

of the vehicle.

3. Yellow Connect with the red cable of the Piezo

signal device. Connect the black cable of

the signal device to earth.

4. White Connect with the red cable of the LED.

Connect the black cable of the LED to

earth.

5. Green Do not use. Insulate the cable using

insulating tape.

6. Blue Do not use. Insulate the cable using

insulating tape.

TRANSPONDER ALIGNMENT

The correct alignment of the transponder is very important.

It should be aligned correctly vertically and horizontally.

Vertical alignment: Upwards / Downwards. The transponder

can be adjusted upwards or downwards by turning the angle

iron included in the package. This is the vertical alignment.

Make sure the vehicle is level. Use the water leveller in-

cluded in the package to adjust the vertical position. Place

the water leveller just above the transponder and fasten

the transponder in the correct position.

Horizontal alignment: Left / Right. The transponder can be

turned around itself using the tee bolt. This is the horizon-

tal alignment. The transponder should be placed at a right

angle of the vehicle.

ENGLISH

90°90°

CALCULATION TABLE FOR THE

INSTALLATION OF THE TRANSPONDER

Use the table below when mounting the transponder in

the grill or behind a vent hole of the vehicle. Mounting

the TARGET LaserTrack using the parameters below guar-

antees maximum performance.

ENGLISH

Measurements are in millimetres

Minimum height H 6 8 9 10 11 13 14 15 16 18 19 20 21

Minimum width W 16 18 21 23 26 28 31 33 36 38 41 43 46

Maximum depth D 0 12 24 36 48 60 72 84 96 108 120 132 144

Minimum height H 23 24 25 26 28 29 30 32 33 34 35 37 38

Minimum width W 48 51 53 56 58 61 63 66 68 71 74 76 79

Maximum depth D 156 168 180 192 204 216 228 240 252 264 276 288 300

Cross-section of laser beam increases

with increase in distance D.

Grill/vent opening

TESTING THE OPERATION

The correct operation of the system can be tested after

the TARGET LT400 has been installed according to the

instructions.

1. Switch the system on by starting the vehicle

(if the switch has been added then it must be

set to ON).

Result: The system emits a short audio signal and the

LED is switched on for 2 seconds. The LT400 will be in

test mode for 10 seconds.

2. Test the operation of the laser receiver using an

infrared remote control device (for audio or video

equipment). Hold the remote control device in

front of the transponder lens (at a distance of

approximately 10 cm) and at the same time press

a button of the remote control device.

Result: The system emits a warning signal and the

LED is switched on.

3. Stop pressing the button of the remote control

device when you are satisfied that the system is

functioning correctly.

Result: After the last received signal the LED will be

switched on for 10 seconds. After the 10 seconds have

elapsed the system will emit two short audio signals.

The LT400 is now in the stand-by mode.

IMPORTANT INFORMATION

FOR ALL USERS

•

Check frequently whether the lens of the transponder

is dirty. The effect of dust and grit on the function-

ing of the system is very limited. Objects that cover

the lens completely, such as leaves or insects, should

be removed at once.

•

Check frequently whether the housing and the lens

of the transponder show signs of damage.

Contact your dealer if the lens is damaged.

•

A dealer should check the tuning of the transponder

periodically (for example, when the vehicle is

serviced).

ENGLISH

FAQ ABOUT TARGET LASERTRACK

1. Can other Target LaserTrack users gain access to

my grounds or garage?

No, Target LaserTrack has more than 4.5 thousand

million unique codes. Only vehicles for which the

code has been programmed in the basic transponder

can gain access.

2. Does the Target LaserTrack laser beam damage

the eye?

No, the Target LaserTrack is a Class 1 laser and is,

therefore, completely safe.

3. Can I control other systems or equipment than

those mentioned in the manual using the

Target LaserTrack?

Yes, in principle all electrical systems can be

switched on and off remotely using the Target

LaserTrack. We recommend contacting the dealer

for the system before applying the Target LaserTrack.

4. Does the Target LaserTrack meet all the legal

requirements and can I legally use the system

anywhere?

Yes, the Target LaserTrack meets the highest

European standards for automotive accessories.

Although interference with other equipment such as

laser guns cannot be ruled out, the system may be

used everywhere for the purpose it was developed.

The system may not be used for other purposes than

that for which it was developed by the manufacturer.

5. Is the Target LaserTrack influenced by police laser

guns or other infrared laser systems?

Yes, every laser gun or other laser system that emits

on a frequency of 904 nanometre is recognized by

the Target LaserTrack as an external source of inter-

ference. The Target LaserTrack shall always switch

itself off after a few seconds to prevent mutual

interference.

ENGLISH

INSTALLATION OF THE LT425 CONTROL

CIRCUIT BOARD AND THE LT420 BASIC

TRANSPONDER

MOUNTING THE LT420 BASIC TRANSPONDER

1. The LT420 basic transponder is mounted in the same

way as the LT400 car transponder. Ensure that the

transponder is mounted at a location where it can

detect the arriving vehicle. Avoid mounting it behind

bushes or other obstacles.

2. Mount the LT420 at the same height or as near to

it as possible as the LT400 on your vehicle. This is

especially important to guarantee the communication

between the vehicle transponder and basic transpon-

der at a short distance.

3. Make sure the cable is long enough to reach the

location where the control circuit board is mounted.

4. Ensure that the cable cannot be pinched. Especially

when the system is used to open and close gates.

5. Connect the plug of the LT420 to the control circuit

board.

Two LT420 transponders can be connected to the control

circuit board (depending on the actual circumstances).

CONNECTING THE LT 425 CONTROL

CIRCUIT BOARD TO THE GATE OR

GARAGE DOOR

The control circuit board is connected to the garage door

or gate differently depending on the brand and type of

door or gate.

Refer to the garage or gate system dealer for instruc-

tions for the connection of the system to your gate

or door.

The switching off can be delayed by 5 to 120 seconds

when the potentiometer is connected to the control cir-

cuit board. Turn the potentiometer in the direction of the

arrow to increase the delay.

The control circuit board should be placed in a separate

waterproof cabinet if it cannot be placed inside the gate

or garage door switch box.

ENGLISH

PROGRAMMING THE

TARGET LASERTRACK

1. Park your vehicle at a few meters distance and in

line with the basic transponder. Make sure that the

LT400 is in stand-by mode.

2. Press the BUTTON-1 or BUTTON-2 button (depending

on the group it is connected to) on the control circuit

board for 2 seconds.

Result: The corresponding LED blinks. LED 10 shall blink

for 10 seconds and it will subsequently start flash-

ing when the code from the LT400 is received.

The code of the vehicle is saved in the memory.

Result: The corresponding led blinks repeatedly for

30 seconds after which it returns to the usual

flashing pattern. This means that the code of

the vehicle has not been received. Check the

position of the vehicle and the basic trans-

ponder and repeat the procedure from step 2

onwards.

A maximum of 50 vehicles can be programmed into the

system in the above manner.

Program the second transponder in manner described

above if you have connected two LT420 transponders

to a single control circuit board.

Important: The car transponder concerned has to be

reset after programming the LT400 car transponder.

The LT400 switches off after a programming cycle to

prevent the gate or garage door to be opened imme-

diately.

DELETING VEHICLES FROM

THE BASIC SYSTEM MEMORY

All the codes saved in the memory of the connected

transponder shall be deleted if you press BUTTON-1

or BUTTON-2 for more than 5 seconds. The LED shall

blink 5 times to confirm it.

The vehicles that should have access should be pro-

grammed into the memory again.

ENGLISH

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Target Radarwarngerät Handbücher

Target

Target LRC 100 Bedienungsanleitung

Beliebte Radarwarngerät Handbücher anderer Marken

Cobra

Cobra XRS 9700 Bedienungsanleitung

Inforad

Inforad v3 Bedienungsanleitung

Cobra

Cobra ESD9200 Betriebsanleitung

Escort

Escort C65 Bedienungsanleitung

Cobra

Cobra SPX 7800BT Bedienungsanleitung

Escort

Escort max 360c Bedienungsanleitung

Cobra

Cobra XRS 9940 Bedienungsanleitung

Lowrance

Lowrance LRA-2400 Bedienungsanleitung

Cobra

Cobra ESD-9160 Bedienungsanleitung

Whistler

Whistler CR80 Bedienungsanleitung

Stinger

Stinger VIP Bedienungsanleitung

Cobra

Cobra XRS 9430 Bedienungsanleitung

Cobra

Cobra Pro 9680 Betriebsanleitung

Escort

Escort SmartRadar Bedienungsanleitung

Whistler

Whistler 1655 Bedienungsanleitung

Radenso

Radenso Pro M-Edition Bedienungsanleitung

Rocky Mountain

Rocky Mountain RMR-D250 Bedienungsanleitung

Cobra

Cobra XRS 9645 Bedienungsanleitung