Tarheel Antennas 400A Bedienungsanleitung

PROUDLY MADE IN THE

UNITED STATES OF AMERICA

Tarheel Antennas, Inc.

Instruction Manual

for the

Model 400A

Continuous Coverage

HF Antenna

18511 CR 304

St. Joseph, MO 64505

816-671-9409 / 816-364-2619 Fax

E-mail: sales@tarheelantennas.com

Technical Support

919-552-8788

E-mail: tarheelanten[email protected]m

www.tarheelantennas.com

Thank you for purchasing the

Model 400A Tarheel Antenna

Packing List for Model 400A

Model 400A Antenna

6 ft. Stainless Steel Whip

Up/Down Switch

20 ft. Control Cable

Ferrite Core

Fuse Holder & Fuse

1 tube of Dielectric Compound

Manual

Packing List for Model 400A Package

All of the above - - plus the following

MT-1 Antenna Bracket

Quick Disconnect for the Whip

21 ft. of RG-8X Coax with connectors installed

1 pack of Coax Seal

Model 400A Antenna Specifications

Lower Mast Length –4ft.

Frequency Coverage with 6’ whip – 1.7 to 26 MHz

Power Rating –250 watts P.E.P.

Typical SWR –1.5 to 1 or less

Total Height with 6’ whip at 25 MHz – 10’4”

Total Height with 6’ whip at 1.7 MHz – 12’4”

Weight –9.0 lbs.

Picture 1 –MT-1 & MT-30FB

Installation

Before installation of this antenna there are a few

things you have to consider. To get peak performance you

need to try to mount the antenna in a location where the

decoupler (this is where the coil comes out of the antenna)

is at least as high as the highest part of the vehicle. Next,

and this is the most important is the vehicle ground must

be within 12 inches of the base of the antenna. This

ground path should be provided with ground strap at least

1/2 inch wide.

After installation if the SWR will not go below 1.5 on the

frequencies above 10 MHz it's because of the ground path

mentioned above. Again, ground close to the base is most

important with this and any other antenna.

This is a large antenna that will require heavy duty mounts

to withstand the pressure produced from the wind load. All

of Tarheel Antenna mounts are designed to take this load.

While we have a variety of mounts lay the antenna down

horizontally, it’s designed to be mounted vertically. While

using these mounts, just make sure the anti-rotation rib on

the antenna will be at the bottom while in the horizontal

position.

Picture 2 –MT-1 & MT-5

Picture 3 –MT-1 & MT-3FB

Picture 4 –MT-1 & Automatic Lift & Lay

Picture 5 –MT-1 & MT-3

The MT-1 antenna bracket is designed to make your antenna

mounting convenient and incredibly strong. Made to clamp to

standard 1” pipe (1.312 OD) or bolted to a flat surface.

(Picture 6)

There are a few steps to make sure you

install the MT-1 antenna bracket the way it is

intended. First you need to install the upper

half of the quick disconnect in the bottom of

the antenna tight (Picture 7). Be sure to use

the lock washer.

The MT-1 antennas bracket has 6 cutouts for the anti-

rotation rib that’s on the antenna. Be sure the rib goes

into one of these cutouts, there is no need to cut the

insulator, it will compress enough to tighten the antenna

down, (Picture 8)

Don’t forget to tighten down

the top half plate and the quick

disconnect. (Pictures 9 & 10)

Picture 7

Picture 8

Picture 6

Picture 9

Picture 10

Included with the antenna is a special mix

#31 ferrite core that needs to be mounted

on the control wire as close to the

antenna as possible. Loop the wire

through the choke at least 3 times.

(Picture 11) It is used to decouple the

control cable from the antenna. If you fail

to install this ferrite core acts like a single

radial and the antenna will be untunable.

The up/down switch (Picture 12) that comes

with the antenna package will plug directly into

the control cable to the antenna, then there will

be 2 wires left on the switch. One will be white

with red dots and one red with black dots. This

system is designed for a standard 12vdc

system. Keep in mind polarity of these two wires

are not important. With the switch mounted up

(wire to bottom) you can wire the red wire with

black stripes to positive side of your 12vdc

system, and the white wire with red stripes to

the negative side. This will allow the antenna to

go up while you press the up button (this is

the way most wire up to their systems). Up

on the switch means the antenna is going UP in the band and DOWN in the bottom (this

is the way most wire up to their systems). Up on the switch means the antennas is

going up in height and Down in frequency. If you prefer that is reversed all you have to

do is reverse the connections. Be sure you add the fuse to the positive side.

Most installs:

Red with black dots –12 volt positive

White with red dots –12 volt ground

Picture 12

Picture 11

Now You Need To Install The Top Whip

Whip Length versus Frequency Coverage

4 ft. -- 1.8 MHz to 30.0 MHz

5 ft. -- 1.7 MHz to 28.0 MHz

6 ft.-- 1.6 MHz to 26.0 MHz

8 ft.-- 1.5 MHz to 20.0 MHz

12 ft.-- 1.2 MHz to 15.0 MHz

CH-1 -- Capacitance Hat

Hat only -- 1.8 MHz to 30.0 MHz

Hat with 3 ft. whip –1.6 MHz to 25.0 MHz

Hat with 6 ft. whip –1.5 MHz to 21.0 MHz

Our standard whip is 6 ft. long; it can be cut to any length for the coverage you need.

Keep in mind that the longer your whip is the better the performance will be on the

lower bands, however you will loose your upper frequencies with the longer whip.

Always try to use the longest whip possible for best performance. After mounting of the

antenna you need to route your antenna control cable and your coax cable in a location

away from exhaust pipes and anywhere the cable can be damaged.

Next is the control box and control cable. We preassemble everything here so you'll

have a plug and play system.

If properly installed this antenna will have a standing wave below 1.5 from 1.8 to 30

MHz. We know that every antenna installation is unique and it is impossible to describe

all the scenarios in this manual. However, if you are having problems with this initial

tuning please call.

Operation

Remember that when the coil is all the way in, it's resonant on the high bands and

all the way out, on the low bands. It will take a little time to get use to this style of

antenna, some mark the antenna with tape to mark the approximate location of the

bands, some just listen to the noise level increase on the radio's receive when it's close

to resonant. When you fine tune you need to transmit a low carrier (AM, FM, CW) at 5

watts and watch the SWR meter till the dip.

Relative Tuning Positions

The following photos will show you relative tuning positions of the Model

400 Tarheel Antennas.

LEXAN COVER REMOVED FOR CLARITY

Model 400 -- full down position with

5 ft. whip -- 28.0 MHz

Model 400 -- 21.2 MHz with 5 ft. whip

Do not try to twist or turn the bug shield on

the outside of the antenna, this is designed

not to turn.

Model 400 -- 14.2 MHz with 5 ft. whip

and 1/2" of coil showing

Model 400 -- 7.1 MHz with 5 ft. whip

and 1 1/2" of coil showing

Model 400 -- 3.9 MHz with 5 ft. whip

and 4" of coil showing

Model 400 -- 3.5 MHz with 5 ft. whip

with 5" of coil showing

Model 400 -- 1.9 MHz with 5 ft. whip

and 15" of coil showing

Model 400 -- 1.8 MHz with 5 ft. whip

and 16 1/2" of coil showing

Maintenance

Very little maintenance is required for your Tarheel Antenna. You should have years of

trouble free service from this antenna. You've made a large investment for a mobile

antenna. Here is a tip to help take care of your investment.

We use an automotive finish on this antenna so whenever you wash and wax your

vehicle raise your antenna and wash and wax the shaft and the bug shield (Lexan tube),

with wax on your antenna the bugs will have a harder time sticking to it.

About once per year or so, depending on how much driving you do and where the antenna is

mounted you will need to wash the coil to remove any road grime, no parts to replace. Also a

dirty coil will show vertical black streaks.

Here's how to clean the coil:

1. Run the antenna up till all the coil is exposed.

2. Remove the are 3 screws in the top Delrin Cap.

3. Then slide the Lexan bug shield down to expose the coil, next feel the coil, is it sticky?

4. If so it's dirty, now wipe the coil with alcohol.

5. Then lightly scrub the coil with a Scotch-Brite pad (available at any hardware store).

6. Then one more wipe with alcohol and that's it.

7. Reassemble the Antenna.

After you have the antenna reassembled, now is the time for a good cleaning on the outside.

Use the alcohol to remove the grime off the tube and Lexan, next get a good coat or two of

wax on it.

Warranty & Guarantee

IF for the 1st 30 days if for any reason you are not completely satisfied, return the

antenna undamaged for a full refund less the shipping charges. The antenna has a

ONE YEAR NO MATTER WHAT WARRANTY to the original owner. If for any reason

(other than damage due to unauthorized disassembly, negligence, improper

use, or use of Non-recommended Controllers) your Tarheel Antenna fails to

perform due to quality or workmanship Tarheel Antennas, Inc. will at our discretion

either repair or replace at no charge for parts or labor. Shipping charges are your

(the customer's) responsibility to and from Tarheel Antennas' repair shop. We here

at Tarheel Antennas hope you enjoy one of the best performing, best built, best looking

motorized antennas available.

We here at Tarheel Antennas hope you enjoy one of the best performing, best built,

best looking motorized antennas available.

Please pass along any suggestions you may have to make our antenna better.

All suggestions are appreciated. Also when you have your antenna installed please

send us pictures.

Thanks,

Tarheel Antennas

Inhaltsverzeichnis

Andere Tarheel Antennas Antenne Handbücher

Tarheel Antennas

Tarheel Antennas Little Tarheel HP Bedienungsanleitung

Tarheel Antennas

Tarheel Antennas Little Tarheel II Bedienungsanleitung

Tarheel Antennas

Tarheel Antennas MFJ-1792 Bedienungsanleitung

Tarheel Antennas

Tarheel Antennas 40A-HP Bedienungsanleitung

Tarheel Antennas

Tarheel Antennas 300A Bedienungsanleitung

Tarheel Antennas

Tarheel Antennas 100A-HP Bedienungsanleitung

Tarheel Antennas

Tarheel Antennas Stubby 75A Bedienungsanleitung

Tarheel Antennas

Tarheel Antennas 200A-HP Bedienungsanleitung

Tarheel Antennas

Tarheel Antennas Little Tarheel II Bedienungsanleitung

Beliebte Antenne Handbücher anderer Marken

Alfa Network

Alfa Network APA-L01 Bedienungsanleitung

Naval

Naval PR-422CA Bedienungsanleitung

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Bedienungsanleitung

TERK Technologies

TERK Technologies TV44 Bedienungsanleitung

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Bedienungsanleitung

HP J8999A Bedienungsanleitung

MobilSat

MobilSat MSP-S Bedienungsanleitung

Steren

Steren ANT-UHF 13 Bedienungsanleitung

Novatel

Novatel 600-G Bedienungsanleitung

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Bedienungsanleitung

TRENDnet

TRENDnet TEW-AO12O Bedienungsanleitung

Radio Shack

Radio Shack 15-1837 Bedienungsanleitung

CommScope

CommScope CMAX-OMFX-43M-I53 Bedienungsanleitung

Ramsey Electronics

Ramsey Electronics DAP25 Bedienungsanleitung

COBHAM

COBHAM SAILOR 800 VSAT Gebrauchs- und Pflegehandbuch

Trango Systems

Trango Systems AD900-9 Bedienungsanleitung

Steren

Steren ANT-100 Bedienungsanleitung

Proxim

Proxim 5054-PA-23 Bedienungsanleitung