Tascam IF-FW Bedienungsanleitung

»D00830000A

OWNER'S MANUAL

Contents

Introduction .................. 2

Installation ................... 3

Setup ....................... 5

IF-FW/DM

FireWire Interface Card

Introduction

Thank you for purchasing the TASCAM IF-

FW/DM FireWire audio card for TASCAM mix-

ers. It is designed to provide audio and MIDI

interfacing between your TASCAM mixer and

your computer based DAW, essentially turning

your TASCAM mixer into a FireWire

audio/MIDI interface.

Please take some time to look through this owners

manual and familiarize yourself with the IF-

FW/DM's features, setup and operation. We sug-

gest you pay particular attention to the setup notes

for your computer platform of choice (Mac or

PC). You may also need to refer to your soft-

ware's documentation for a clear understanding of

how to setup an audio/MIDI interface from within

your software. Your experience with the IF-

FW/DM will be greatly enhanced by a good

working knowledge of your audio software.

Be sure to check the TASCAM web site at

www.tascam.com and ensure you have the latest

software updates for your IF-FW/DM.

Features

The IF-FW/DM provides the following interfac-

ing between your TASCAM mixer and a host

computer via FireWire:

•24 channels of Input to the mixer from the

computer at 44.1k and 48k sample rates

• 24 channels of Output from the mixer to the

computer at 44.1k and 48k sample rates

• 1 MIDI port In and Out from the computer

System Requirements

Macintosh

•OS: MacOS X 10.3.5 or higher

•Computer: Apple Macintosh series with on-

board Firewire

•Minimum: G4/800MHz

•Recommended: Dual G4/1GHz

•Memory(RAM): 256MB or more

Windows

•OS: Microsoft® Windows® XP Home Edition

or XP Professional with Service Pack 1

•Computer: Windows® XP Compatible PC

equipped with an IEEE 1394/FireWire Port

•Minimum: Pentium®, Celeron®, or Pentium®

compatible processor 1.5GHz or higher

•Recommended: Pentium® IV/2GHz or higher

•Memory(RAM): 256MB or more

DM-24 Requirements

The DM-24 must be running V3.00 software to

use the IF-FW/DM. Please refer to www.tas-

cam.com or your local service center to obtain

this DM-24 update. Do not proceed to install the

IF-FW/DM until your DM-24 has been updated.

Windows and Windows XP are trademarks of

Microsoft Corporation.

Macintosh, MacOS, MacOS X and FireWire™

are trademarks of Apple Computer.

All other trademarks are the property of their

respective holders.

Installation

Installing the IF-FW/DM

•The IF-FW/DM must be installed in the DM-

24's Slot 1. It will not function in Slot 2.

•The following installation must be done with

the DM-24's power OFF and disconnected.

1. Remove the five screws holding the blank

plate or card currently installed in Slot 1, and

then remove the plate or card.

2. Insert the IF-FW/DM into Slot 1, making sure

that the card edges slide into the white plastic

guide inside Slot 1. Push it all the way in until

it clicks and the card back plate is flush with

the DM-24's back panel. Excessive force is

not required - if it doesn't click in easily,

remove it and start again with attention to the

guides.

3. Replace the five screws to hold the card in

place.

Making Connections

•The maximum FireWire cable length is 3

meters.

1. Connect one end of the provided FireWire

cable to the IF-FW/DM and the other end to an

available FireWire port on your computer.

2. Connect the MIDI Input of the IF-FW/DM to

the MIDI Output of the DM-24 if you plan to

use the DM-24 as a control surface for your

DAW.

3. Connect the MIDI Output of the IF-FW/DM to

the MIDI Input of the DM-24 if you plan to

drive the DM-24's automation from MTC pro-

vided by the DAW or if you require time code

display from the DAW in the DM-24's read-

out.

a. If you will not be using MIDI communica-

tion between the DM-24 and the DAW for

surface control or time code, the IF-

FW/DM's MIDI port may be used as an

additional MIDI port by the DAW's

sequencer. It can be used to connect a

MIDI controller, sound module or sampler.

NOTE: The IF-FW/DM must be connected by

itself on a FireWire bus. More than one FireWire

connector on a computer does not mean each con-

nector has its own bus. More often, all connec-

tors go to the same bus on the computer. If you

require additional FireWire devices, it is neces-

sary to add a FireWire card, thus adding a sepa-

rate bus, for those devices.

Configuring the Computer

Macintosh

The IF-FW/DM uses the FireWire audio/MIDI

services provided by OSX so it is not necessary to

install drivers. You must have OSX 10.3.5

installed on your Mac to use the IF-FW/DM.

Previous operating systems do not include the

correct built-in services.

1. Make the connections as described above.

2. Power up the Mac

3. Power up the DM-24

4. Open Audio/MIDI set and verify that the IF-

FW/DM device is present

5. Configure your DAW to use the IF-FW/DM

Core Audio device according to the instruc-

tions for your app.

•If the computer does not recognize the card,

disconnect the FireWire cable for 30 seconds

then reconnect it (Mac), increase the Stream

Buffer Depth in the control panel (PC) or use

the Reset Cards command under the control

panel Tools menu (PC).

Installation

Windows

It is necessary to install driver software in order

for Windows to recognize the IF-FW/DM. An

installer is provided for this purpose, the drivers

cannot be installed manually from Windows

Device Manager. On the CD-ROM that came

with your IF-FW/DM is a PC Drivers installer.

Launch it from the CD or copy it to your hard

drive and launch it from there.

•The IF-FW/DM should be disconnected from

the PC for driver installation.

1. Launch the driver installer and carefully fol-

low the on-screen instructions in the

Installation Wizard.

2. When presented with the Windows Logo

warning, click Continue Anyway.

3. Follow the steps on the final screen of the

Installation Wizard through the Windows

"New Hardware Wizard". Leave the selection

on the default setting of "Install the software

automatically (recommended)". You will go

through two New Hardware Wizards.

4. When "Your new hardware is installed and

ready to use" appears in the lower right of the

Windows desktop, click on "I Completed the

Above Steps" in the IF-FW/DM Setup win-

dow.

5. Another Windows "New Hardware Wizard"

will appear, click Next. Leave the selection on

the default setting of "Install the software auto-

matically (recommended)".

6. When presented with the Windows Logo

warning, click Continue Anyway.

7. When the installation activity is done, click

Finish.

8. "Your new hardware is installed and ready to

use" will appear again in the lower right of the

Windows desktop.

9. Configure your DAW to use the IF-FW/DM

WDM or ASIO device according to the

instructions for your app.

NOTE: Because WDM mode takes longer to be

recognized than ASIO mode, WDM mode is

defaulted to Off. It will have to be manually

turned on if you are using a WDM app. There is

a check box in the PC control panel to enable

WDM mode.

•If the computer does not recognize the card,

disconnect the FireWire cable for 30 seconds

then reconnect it (Mac), increase the Stream

Buffer Depth in the control panel (PC) or use

the Reset Cards command under the control

panel Tools menu (PC).

Setup

IF-FW/DM Interface Setup

Below are brief instructions for setting up com-

mon DAW software apps to use the IF-FW/DM

interface. If you app isn't covered here, but does

support ASIO (PC), WDM (PC) or Core Audio

(Mac), or if you need more detailed instructions

to configure your app, please refer to the docu-

mentation for your app to set up an audio/MIDI

interface.

Cubase / Nuendo

1. Select Device Setup under the Devices menu

2. Select VST Multitrack

3. Select ASIO IFFWDM under the ASIO Driver

pulldown

4. Click Apply then click OK

SONAR

1. Select Audio under the Options menu

2. Click the Drivers tab and enable the desired

Inputs and Outputs

3. Click the General tab and select IF-FW/DM

devices for the Playback and Record Timing

Masters

4. Click on Wave Profiler (run this any time you

change anything in this window)

5. Click on Yes to profile the interface. The sam-

ple rate corresponding to the sample rate set on

the mixer will show "OK". Other sample rates

will show "not available". Close this window

6. Click OK

Logic

1. Under the Logic menu, select Preferences >

Audio Hardware & Drivers

2. Ensure that Core Audio is checked and click

the triangle on the left to expand the window

3. Select the IF-FW/DM in the Driver pulldown

4. Click OK

Digital Performer

For the IF-FW/DM to work with Digital

Performer, version 4.5 or higher of DP must be

used.

In DP 4.5, there is a setting that reduces the MAS

thread priority in the System. The medium or low

setting should be used with the IF-FW/DM.

Effectively under this setting, the IF-FW/DM can

achieve an equal track & plug-in count under DP

as other FW audio interfaces that can run at high

MAS thread priority. However, on slower CPU's,

MAS could be more prone to processor spikes on

larger DP projects.

1. Under the Setup menu, select Configure Audio

System > Configure Hardware Driver

2. Highlight the IF-FW/DM to make it the select-

ed Core Audio device for DP.

3. Configure the Buffer Size and Host Buffer

Multiplier according to your Mac's capabili-

ties. Generally, less powerful Macs will

require higher settings.

4. Click OK

System Clocking

Master Clock

When configured with an IF-FW/DM, the DM-24

must be the master clock relative to the computer

DAW. The DM-24 itself may be clocked to an

external source other than the DAW.

Clock Settings

If it becomes necessary to switch between 44.1k

and 48k sample rates on the DM-24, the follow-

ing steps are required for correct operation:

1. Disconnect the FireWire cable between the IF-

FW/DM and your computer.

2. Change the sample rate on the DM-24.

3. Re-connect the FireWire cable.

NOTE: 30 seconds must elapse between discon-

nection and reconnection of the FireWire cable.

96k & 88.2k Operation

At the time of this writing, the IF-FW/DM does

not support high sample rate mode.

IF-FW/DM & DM-24 Routing

The IF-FW/DM appears to the DM-24 just like

any other optional I/O card except that it has 24

channels of I/O instead of 8.

Mixer Outputs

By default, the DM-24 duplicates busses 1 - 8 on

IF-FW/DM mixer outputs 1 - 8, 9 - 16, and 17 -

24.

Also available are the Direct Outputs from chan-

nels 1 - 16 on the DM-24. By default, those

appear on IF-FW/DM mixer outputs 1 - 16.

These routing settings can be changed in the

Output tab of the DM-24's I/O screen.

Mixer Inputs

The IF-FW/DM's mixer inputs must be config-

ured in banks of 8 in the CH1-16 IN and CH17-

32 IN tabs of the DM-24's I/O screen.

For 24 channel operation:

•Set RETURN CH1-8 to A:SLOT1, Trk1-8,

FW 1-8

•Set RETURN CH9-16 to B:SLOT1, Trk9-16,

FW 9-16

•Set RETURN CH17-24 to A:SLOT1, Trk17-

24, FW 17-24

Set the INPUT SOURCE to RETURN

Setup

IF-FW/DM Control Panel

(Windows)

The IF-FW/DM Control Panel is found here: Start

Menu > All Programs > TASCAM > IFFWDM

Control Panel.

There are three sliders available in the control

panel. Generally, lower audio buffer settings

offer lower latency but require a more powerful

computer. It may be necessary to experiment

with these settings to find the lowest setting your

computer is capable of running. The most com-

mon symptom of settings that are too low for a

particular computer is clicks & pops in the audio.

Enable WDM Audio (Default OFF)

Check this box to enable WDM mode in order to

use the IF-FW/DM with a WDM app. Checking

this box will increase the time required for the IF-

FW/DM to establish communication with the PC.

NOTE: There is status indication in the control

panel of a good connection between the IF-

FW/DM and the PC. If connection is lost, discon-

nect the FireWire cable for 30 seconds then

reconnect it, increase the Stream Buffer Depth or

use the Reset Cards command under the Tools

menu of the Windows control panel.

The three sliders are:

Stream buffer depth

Use this slider to control the size of the incoming

1394 audio stream. The larger the buffer size, the

more latency in the audio. Too small of a buffer

size can introduce clicks and pops in the audio.

ASIO buffer depth

Use this slider to reduce/increase latency when

using a Steinberg ASIO app or when using

SONAR in ASIO mode.

WDM sound buffer depth

Use this slider to reduce/increase latency when

using a WDM app such as SONAR.

After adjusting the sliders, press Apply to set the

changes.

Printed in China

TEAC CORPORATION

Phone: +81-422-52-5082 www.tascam.com

3-7-3, Nakacho, Musashino-shi, Tokyo 180-8550, Japan

TEAC AMERICA, INC.

Phone: +1-323-726-0303 www.tascam.com

7733 Telegraph Road, Montebello, California 90640

TEAC CANADA LTD.

Phone: +1905-890-8008 Facsimile: +1905-890-9888 www.tascam.com

5939 Wallace Street, Mississauga, Ontario L4Z 1Z8, Canada

TEAC MEXICO, S.A. De C.V

Phone: +52-555-581-5500 www.tascam.com

Campesinos No. 184, Colonia Granjes Esmeralda, Delegaacion Iztapalapa CP 09810, Mexico DF

TEAC UK LIMITED

Phone: +44-1923-438880 www.tascam.co.uk

5 Marlin House, Croxley Business Park, Watford, Hertfordshire. WD1 8TE, U.K.

TEAC EUROPE GmbH

Phone: +49-611-71580 www.tascam.de

Bahnstrasse 12, 65205 Wiesbaden-Erbenheim, Germany

TEAC FRANCE S. A.

Phone: +33-1-42-37-01-02 www.tascam.fr

17 Rue Alexis-de-Tocqueville, CE 005 92182 Antony Cedex, France

TEAC AUSTRALIA PTY.,LTD. A.B.N. 80 005 408 462

Phone: +61-3-9672-2400 Facsimile: +61-3-9672-2249 www.tascam.com.au

280 William Street, Port Melbourne, Victoria 3000, Australia

TEAC ITALIANA S.p.A.

Phone: +39-02-66010500 www.teac.it

Via C. Cantù 11, 20092 Cinisello Balsamo, Milano, Italy

IF-FW/DM

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Tascam Aufnahmegeräte Handbücher

Tascam

Tascam HD-R1 Bedienungsanleitung

Tascam

Tascam DS-D98 Bedienungsanleitung

Tascam

Tascam DR-05 Bedienungsanleitung

Tascam

Tascam DP-004 Bedienungsanleitung

Tascam

Tascam US-1800 Bedienungsanleitung

Tascam

Tascam 414MKII PortaStudio Bedienungsanleitung

Tascam

Tascam CD-RW900 Bedienungsanleitung

Tascam

Tascam 564 Digital Portastudio Bedienungsanleitung

Tascam

Tascam dr-44wl Bedienungsanleitung

Tascam

Tascam PORTASTUDIO 788 Referenzhandbuch

Tascam

Tascam MX-2424 Bedienungsanleitung

Tascam

Tascam Portastudio 2488 Benutzerhandbuch

Tascam

Tascam MMR-8 Bedienungsanleitung

Tascam

Tascam DR-40 Bedienungsanleitung

Tascam

Tascam MMR-8 Bedienungsanleitung

Tascam

Tascam CC-222mkIII Bedienungsanleitung

Tascam

Tascam Cubase LE Bedienungsanleitung

Tascam

Tascam CD-RW901 Leitfaden

Tascam

Tascam Frontier HD-P2 Montage- und Bedienungsanleitung

Tascam

Tascam CD-RW900 Bedienungsanleitung

Tascam

Tascam Frontier HD-P2 Bedienungsanleitung

Tascam

Tascam DP-24SD Bedienungsanleitung

Tascam

Tascam DR-V1HD Bedienungsanleitung

Tascam

Tascam Frontier HD-P2 Bedienungsanleitung

Beliebte Aufnahmegeräte Handbücher anderer Marken

KV2 Audio

KV2 Audio 500 Series Bedienungsanleitung

Robotics Technologies

Robotics Technologies microBus-Cam II Bedienungsanleitung

Seca

Seca 460 Bedienungsanleitung

Cognex

Cognex MVS-8000 Series Bedienungsanleitung

Mect

Mect MPNC006 Series Bedienungsanleitung

Bad Caf

Bad Caf THE LEASH Bedienungsanleitung

Strymon

Strymon NIGHTSKY Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Bedienungsanleitung

Tews Technologies

Tews Technologies TPMC465 Bedienungsanleitung

Honeywell

Honeywell Excel 50 Bedienungsanleitung

SeaLevel

SeaLevel COMM+8.LPCI Bedienungsanleitung

Arturia

Arturia AUDIOFUSE STUDIO Bedienungsanleitung

Rukra

Rukra RK-1240 Bedienungsanleitung

Samson

Samson SCOM Bedienungsanleitung

Dynacord

Dynacord DPS260 Bedienungsanleitung

Nice

Nice Core Bedienungsanleitung

Pyle Pro

Pyle Pro PSS8 Bedienungsanleitung

RF-System

RF-System TinyGate Gebrauchs- und Pflegehandbuch