Task Force Tips YE-RF Series Leitfaden
INSTRUCTIONS FOR INSTALLATION
OF RADIO BOARD FOR (YE-RF-##)
TASK FORCE TIPS, Inc. 3701Innovation Way, Valparaiso, IN 46383-9327 USA
800-348-2686 • 219-462-6161 • Fax 219-464-7155
MADE IN USA • www.tft.com
©Copyright Task Force Tips, Inc. 2010 LIY-415 October 4, 2010 Rev00
Observe precautions for handling Electrostatic Sensitive Devices. Be
sure to touch unpainted, exposed metal on monitor or firetruck before
removing and handling circuit boards.
1) Turn off power and remove lid from monitor control box.
Unscrew the lid screws but do not remove screws completely
from lid. Be careful to open lid slowly as lid is connected to
communication board by a flat cable.
Securely support lid during the installation process.
2) Locate connector with blue &
white wires on the small
communication board on the far
left.
3) Unplug connector with blue &
white wires from the
communication board.
Communication
Board
Lid Screw
Lid Screw
TASK FORCE TIPS
®
FIRE FIGHTING EQUIPMENT
®
6) Attach antenna connector to
radio board with the cable in the
orientation. Note, in some RC
monitors, cable tie may need to
be cut to attach antenna.
Antenna
Connector
4) Remove the small
communication board on the far
left. Pull board straight out.
5) Plug radio board into
communication board. Be
careful to line up pins.
Radio Board
Communication
Board
Board
Removed
7) Plug communication
board/radio board into main
board. Press down to seat
securely.
9) Replace lid onto box. Be sure
to guide flat cable down across
motor boards and to not pinch
any wires between lid and box.
Flat cable
10) Tighten lid screws equally in
a criss-cross pattern.
8) Insert connector with blue &
white wires into communication
board.
TASK FORCE TIPS, Inc. 3701Innovation Way, Valparaiso, IN 46383-9327 USA
800-348-2686 • 219-462-6161 • Fax 219-464-7155
MADE IN USA • www.tft.com
©Copyright Task Force Tips, Inc. 2010 LIY-415 October 4, 2010 Rev00
TEACHING ID CODE:
Every monitor has a unique ID code that must be “taught or transferred” to the wireless handheld unit. This unique ID code allows
multiple monitors to be used in one location without interference. Perform the following procedure to teach the handheld unit.
-Press POWER button to turn on electronics.
-Press and hold both LEFT & RIGHT buttons simultaneously for 5 seconds.
-Continue to press the LEFT & RIGHT buttons and then press UP button for 2 seconds.
-Release buttons. After several seconds the OSC & STOW lights will flash rapidly to indicate that the unit is in teach mode.
On Wireless Handheld Unit:
On Monitor Control Box:
-Apply power to monitor.
-Press and hold both LEFT & RIGHT buttons simultaneously for 5 seconds.
-Continue to press the LEFT & RIGHT buttons and then press UP button for 2 seconds.
-Release buttons. After several seconds the OSC & STOW lights will flash rapidly to indicate that the unit is in teach mode. ID
code is automatically transferred to the wireless handheld unit.
-OSC & STOW lights on handheld unit will stop flashing after ID code is transferred.
-Press DOWN button on monitor control box to exit teach mode.
-Cycle power off and back on to monitor.
In the event the handheld unit does not link up with the monitor, perform the following at the monitor operator station and the
handheld unit.
- Turn off power.
- Press and hold DOWN button.
- Apply power to the monitor, continue to hold DOWN button for 3 seconds.
- Release DOWN button.
- After green POWER light stops blinking, test wireless handheld unit.
- Repeat above procedure for “Teaching ID Code”
NOTE: When the wireless handheld operator station is purchased at the same
time as RC monitor, handheld unit will be pre-taught at factory.
NOTE: Before teaching, monitor should be powered down.
NOTE: If multiple monitors are present, apply power only to the monitor being taught, otherwise possible conflicts may
occur.
Inhaltsverzeichnis
Andere Task Force Tips Fernbedienung Handbücher
Beliebte Fernbedienung Handbücher anderer Marken
Panasonic
Panasonic EUR7622KB0 Bedienungsanleitung
Bang & Olufsen
Bang & Olufsen Beo4 Bedienungsanleitung
Sunwave Tech.
Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung
Multiplex
Multiplex PROFI TX 9 Bedienungsanleitung
One Remote
One Remote RMB4 Bedienungsanleitung
FUTABA
FUTABA 9ZAP - PART2 Bedienungsanleitung
