TCS AMI Series Bedienungsanleitung

TCS TürControlSysteme AG, TCS Hotline Deutschland: 0 41 94 / 9 88 11 88 Subject to technical changes.

Fax: 0 41 94 / 9 88 129 E-Mail: info@tcs-germany.de PI_AMI11100-uk 1A

Product information

Series AMI

Built-in door loudspeaker module

AMI11100

Note on the validity of this product information

This product information states specific information on the module.

It is only valid in combination with the enclosed product information Modules of the series

AMI in front-door stations.

2 01/2013

TCS TürControlSysteme AG, TCS Hotline Deutschland: +49 (0) 41 94 / 9 88 11 88 Subject to technical changes.

Fax: +49 (0) 41 94 / 9 88 129 E-Mail: hotline@tcsag.de PI_AMI11100-uk 1A

Scope of delivery

1 x Built-in door loudspeaker module AMI11100

3 x Spacer foil 0.5 mm

1 x 4-pin connecting cable

4 x Securing nut M4

1 x Screwdriver with round handle

Product information built-in door loudspeaker module AMI11100

Product information modules of the Series AMI in front-door stations

Intended use

The built-in door loudspeaker module AMI11100 is a module for front-door stations of

the sereis AMI.

It can be used in combination with other modules of the series AMI (except for function-

al group dispaly modules).

Short description

Connection for bell button module via 4-pin plug connector

Voice-controlled hands-free talking (standard)

Full duplex hands-free talking can be activated for indoor stations with handset

2 indoor stations can be allocated to any bell button provided on site

Error detection and display

Volume and volume acknowledgement tone can be adjusted manually

Pluggable memory to replace front-door stations identical in construction

Further slot to read-in TCU2 memory

R-terminal to extend functionality –door release

Technical data

supply voltage

+24 V ± 8 % (power supply and control unit)

housing

frame with hole lattice

plastics

aluminium, anodised

H x W x D

105 x 115 x 48 mm

weight

275 g

acceptable ambient temperature

−25 °C to +55 °C

input current standby

max. input current

I(a) = 0.1 mA, I(P) = 4.4 mA

I(Pmax) = 140 mA

3-wire technique necessary!

3-wire technique necessary to connect FAA1100 (TOER1)!

01/2013 3

TCS TürControlSysteme AG, TCS Hotline Deutschland: +49 (0) 41 94 / 9 88 11 88 Subject to technical changes.

Fax: +49 (0) 41 94 / 9 88 129 E-Mail: hotline@tcsag.de PI_AMI11100-uk 1A

Overview

1 Microphone

2 Connection for

another Module with 4-

pin connecting cable

(e.g. bell button module

AMI1090x) and Service

Device

3 Service opening with

cover

4 Terminal cover

5 Connection

TCS:BUS®

pluggable screw

terminal

Service opening

2Connection for another Module with 4-

pin connecting cable (e.g. bell button module

AMI1090x) and Service Device

7 Control volume acknowledgement tone

8 Control volume loudspeaker

9 Programming push button

10 Programming LED, red

11 Operation LED, green

(operation and error indication)

12 EEPROM

Installation

The built-in door loudspeaker module must always be installed horizontally into the front

panel (terminals face down).

4 01/2013

TCS TürControlSysteme AG, TCS Hotline Deutschland: +49 (0) 41 94 / 9 88 11 88 Subject to technical changes.

Fax: +49 (0) 41 94 / 9 88 129 E-Mail: hotline@tcsag.de PI_AMI11100-uk 1A

Connecting the lines

Connect the module within the front-door

station

After the installation into the front panel, the

modules themselves have to be wired.

The built-in door loudspeaker module can be

connected to a module with a 4-pin connect-

ing cable (e.g. bell button module):

Remove the cover of the service opening.

Guide the cable upwards from the termi-

nals and push it slightly under the module

housing. Plug the connection cable with 4

pins on the service socket in the service

opening.

Close the service opening and the terminal

cover.

Connect the module to the TCS:BUS®

Das Einbau-Türlautsprechermodul wird

direkt am TCS:BUS®angeschlossen

(3-Drahttechnik, a b P).

AMI11100

Bell button

module l

AMI1090x

Notes on connecting the module with a system

3-wire technique necessary!

Connect buttons from other systems (e.g. elevator):

The buttons must be potential-free. It may be necessary to insert a relay for decoulping

in order to guarantee that the buttons are potential-free.

Connecting other consumers:

It is not allowed to connect further consumers such as tubular lamps, light bulbs or

others to the ASI11000. For this, a separate transformer must be used.

The max. number of indoor stations depends on the type of indoor station (comp. Pro-

duct information of the indoor station).

Attention: When using a FAA1100, the door release time of the power supply and

control unit must be set to maximum!

01/2013 5

TCS TürControlSysteme AG, TCS Hotline Deutschland: +49 (0) 41 94 / 9 88 11 88 Subject to technical changes.

Fax: +49 (0) 41 94 / 9 88 129 E-Mail: hotline@tcsag.de PI_AMI11100-uk 1A

Wiring example 3-wire operation

If more than one front-door station is installed, an additional door release relay

(FAA1100-0600) must be used! Not enclosed in the delivery. Can be ordered from

TCS.

Connection diagram

Connecting line

Acceptable wire cross-section (diameter): 0.08 … 0.82 mm2(0.32 … 1.0 mm)

Max. number of wires per terminal contact:

connection bell buttons: each 2 x 0.8 mm,

connection TCS:BUS®: 3 x 0.6 mm or 2 x 0.8 mm

Further wires must be connected with auxilliar terminals!

Only use connecting lines with the same diameter within a terminal contact.

ISW4100

AMI11100

floor

push button

floor

push button

6 01/2013

TCS TürControlSysteme AG, TCS Hotline Deutschland: +49 (0) 41 94 / 9 88 11 88 Subject to technical changes.

Fax: +49 (0) 41 94 / 9 88 129 E-Mail: hotline@tcsag.de PI_AMI11100-uk 1A

Error detection and indictaion

Errors are displayed optically and acoustically: one-time

error tone and constant flashing of the operation-LED,

green. When pressing a button at a connected bell but-

ton module, the error tone sounds again. The optical

error indication stays active until the error has been

fixed.

11 Operation-

LED, green

Error causes

Display

Error tone

Solution

EEPROM is missing or plugged

incorrectly

Operation-

LED,

green

flashes

(1:7, 1 Hz)

Insert EEPROM,

switch on the main voltage again!

a- and P-wire interchanged or

short-circuited

Interchange a- and P-wire or remove short

circuit, device returns to standby mode

a-wire not connected

Connect a-wire,

device returns to standby mode

Button stucks (press longer than

15 seconds)

Release button,

device returns to standby mode

Settings

Adjust volume of speech and acknowledgement tones

Use the enclosed small screwdriver to adjust the setting!

Open the cover of the secive

openeing.

The volume of speech (loudspeaker)

and acknowledgement tones can be

adjusted via two separate controls.

The volume is set ex works to an

average value.

7 Control acknow-

ledgement tones

8 Control volume

loudspeaker

Configuration

Settings ex works

Communication time

56 s

Door call standby time

56 s

Door release time

3 s

01/2013 7

TCS TürControlSysteme AG, TCS Hotline Deutschland: +49 (0) 41 94 / 9 88 11 88 Subject to technical changes.

Fax: +49 (0) 41 94 / 9 88 129 E-Mail: hotline@tcsag.de PI_AMI11100-uk 1A

Configuration options*

Function

manually

TCSK-01

configoTM

AS-address

–

Communication time

–

Door release time

–

Door standby time

–

Programming lock (ON/OFF)

–

Type of acknowledgement tones

–

Communication only when door standby active

(ON/OFF)

–

Light switch function (via door release button of

the indoor stations) ON/OFF

–

Volume of speech Sprechen

–

Volume of acknowledgement tones

–

Send any control function when pressing a bell

button (serial number of the control function =

serial number of ASI11000)

–

Bell button programming

Send a 16 bit door release command

–

Door release only when door standby is active

–

* The configuration of AMI11100 with the configuration software configo™ must be carried out the same way

as the configuration of ASI11000.

Set AS-address

When combining the door loudspeaker module or the display module AMI1010x with a bell

button module AMI1090x the following must be observed:

The AS-addresses of the built-in door loudspeaker module and bell button module resp.

display module must be the same in order to make a connection.

Set the AS-addresses to the correct value and place a lock on these addresses.

Bell button programming

Refer to Product information Bell button module AMI1090x.

Set functions

Buttons of a connected bell button module which are not allocated, can be used for switch-

ing functions:

Switching lights via bell button

Do not programme the button resp. delete programming

Send control function

Set fnction with device configurator configoTM einrichten

8 01/2013

TCS TürControlSysteme AG, TCS Hotline Deutschland: +49 (0) 41 94 / 9 88 11 88 Subject to technical changes.

Fax: +49 (0) 41 94 / 9 88 129 E-Mail: hotline@tcsag.de PI_AMI11100-uk 1A

Repair

Note

For maintenace, the connections, display LED and push buttons of the module are easily

accessible whithout having to lossen screws. Open the cover of the service opening (see

Overview).

The exchange programming mode cannot be activated when:

The LED operation indication, green blinks slowly (the programming mode of the

system is activated at the power supply and control unit) or

The LED, green flashes (error indication).

ATTENTION!

Remove and insert an EEPROM only when in idle condition!

Accessory

Short text

Article number

Maintenance package

FBI1210-0

Service

For questions please contact

[email protected]

Headquarters

TCS TürControlSysteme AG, Geschwister-Scholl-Str. 7, D - 39307 Genthin

Tel.: +49 (0) 39 33 / 87 99 10, Fax: +49 (0) 39 33 / 87 99 11, E-Mail: info@tcs-germany.de, Internet:

www.tcsag.de

Andere Handbücher für AMI Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere TCS Gegensprechanlage Handbücher

TCS

TCS IVW2211-0218 Bedienungsanleitung

TCS

TCS PDS Series Bedienungsanleitung

TCS

TCS ISW3030 Bedienungsanleitung

TCS

TCS ISW5010-0145 Gebrauchsanweisung

TCS

TCS CAI2002-0140 Bedienungsanleitung

TCS

TCS ISW3130-0140 Bedienungsanleitung

TCS

TCS SKYLINE:TEN BASIC Bedienungsanleitung

TCS

TCS Tasta Series Bedienungsanleitung

TCS

TCS ISH3230 Bedienungsanleitung

TCS

TCS IVW2221-015x Bedienungsanleitung

TCS

TCS Carus Adapto Bedienungsanleitung

TCS

TCS PVU14 0-0010 Series Bedienungsanleitung

TCS

TCS IVX9001-0140 Bedienungsanleitung

TCS

TCS ECOOS:FIVE Bedienungsanleitung

TCS

TCS ISH3022 Bedienungsanleitung

TCS

TCS Carus Origo CAI2010 Bedienungsanleitung

TCS

TCS Carus Adapto Bedienungsanleitung

TCS

TCS IMM2500 Bedienungsanleitung

TCS

TCS AVU14 0 Series Bedienungsanleitung

TCS

TCS ISH3030 Gebrauchsanweisung

TCS

TCS ISH3030-0140 Bedienungsanleitung

TCS

TCS IVH3222 Bedienungsanleitung

TCS

TCS ISW3030-0140 Bedienungsanleitung

TCS

TCS AVU940x0 Bedienungsanleitung

Beliebte Gegensprechanlage Handbücher anderer Marken

Bticino

Bticino LINEA 3000 Bedienungsanleitung

MSI

MSI MSI-140 Bedienungsanleitung

golmar

golmar Stadio Plus Bedienungsanleitung

CyberData

CyberData 011211 series Handbuch

Vidos

Vidos duo M1021 Bedienungsanleitung

Vimar

Vimar ELVOX 7539/E Bedienungsanleitung

SSS Siedle

SSS Siedle BTSV 850-03 Bedienungsanleitung

Dahua

Dahua VTO Series Bedienungsanleitung

Elvox

Elvox 5651 Bedienungsanleitung

Videx

Videx VIDEOKIT Series Bedienungsanleitung

Rocom

Rocom Doortello Business FW T2.05W2.04 Bedienungsanleitung

Viking

Viking E-35-EWP Bedienungsanleitung

Safeguard Supply

Safeguard Supply LRA-EX1000 Bedienungsanleitung

SSS Siedle

SSS Siedle BFCV 850 Series Bedienungsanleitung

GRD

GRD MAX V2 Bedienungsanleitung

Alecto

Alecto ADI-250 Bedienungsanleitung

Aiphone

Aiphone IE-8MD Bedienungsanleitung

Perel

Perel EDB4 Bedienungsanleitung