Teac FD-235 Series Bedienungsanleitung

TEAC FD-235 Series

3 1/2" 1.44 MB Floppy Disk Drive

Installation Guide

3 1/2'' diskette

insertion window

Activity indicator

Eject Button

Your FD-235 package includes:

* FD-235 3 1/2" floppy disk drive

* Installation Guide

Introduction

Thank you for purchasing the TEAC FD-235 Series 1.44 MB floppy disk

drive. This product is intended for use in IBM PC/AT compatible computers.

This quality drive will provide trouble-free operation for your computer

system if properly installed. PLEASE READ THE ENTIRE INSTALLATION

GUIDE THOROUGHLY BEFORE YOU BEGIN THE INSTALLATION.

Use a standard floppy controller card or the floppy connector (34 Pin) on

the motherboard.

Preparing your Personal computer for FD-235 Floppy Drive Installation

1. Unplug your computer from the power source.

2. Remove cover from your computer. Refer to your computer system

manual for this procedure.

3. If you are replacing a current floppy, note the cables that are connected

to your floppy disk drive, as these same cables will be required to install

your FD-235. The floppy interface cable is the flat “ribbon” type, and

the power connector consists of the 4 or 2 separate wires attached to a

single connector. See Figure A.

Your system may also have a single ground wire attached to the floppy

disk drive. Carefully disconnect all cables from your floppy disk drive.

Remove original floppy disk drive.

4. Install the FD-235 Series 1.44 MB into an available drive bay.

Rear View of FD-235

CAUTION: TURN OFF YOUR COMPUTER AND UNPLUG IT FROM

THE AC POWER SOURCE BEFORE INSTALLING THE FD-235.

FAILURE TO DO SO MAY RESULT IN ELECTRIC SHOCK.

Traditional power connector

from PC power supply

Pin #1 indicator stripe

(red or blue)

Flat “ribbon” cable

Power connector

FIGURE A

Pin #1

Configuring for A: or B: drive

Use a standard IBM PC compatible cable with a twist at the end connector

(Figure B) to complete installation. Cable’s colored-line denotes Line 1 to

match to Pin 1 on drive and motherboard’s connectors.

a. To configure as your A: drive, connect the FD-235 Series floppy drive to

Connector A: on the flat “ribbon” cable. Connector A: is the end

connector of the cable as shown in Figure B.

b. To configure as your B: drive, connect the FD-235 Series floppy drive to

Connector B: on the flat “ribbon” cable. Connector B: is the middle

connector of the cable as shown in Figure B.

c. Make the correct changes to the CMOS BIOS setup after you install

your FD-235. Configure Floppy A: to 3.5" 1.44 MB.

d. Upon rebooting, the Operating System (DOS, Windows) will recognize

the floppy disk drive. There are no drivers required.

FIGURE B

Pin #1 I/F Cable Twist

Connector B: Connector A:

TEAC Tech Support: If you have questions on the floppy installation, please

Phone: 323-727-4860

Fax: 323-869-8751

Email: [email protected]

Hours: M-F 8am-5pm PST

Website: www.teac.com/DSPD/techsupport.htm

*IBM PC/AT are registered trademarks of International Business Machines Corp. Rev. TRG 2/02

Symptom

Indicator light never turns on when

executing READ or WRITE

Indicator light comes on as soon as

power is applied and stays on.

Drive type mismatch during boot

Invalid media or Track 00 bad when

formatting.

The same directory is displayed for

different diskettes.

Drive not ready error reading drive X.

General failure error reading drive X

Sector not found error.

Solution

Ensure proper interface cable and power

cable connection and CMOS setup

configuration.

The ribbon cable may be reversed. Check

Pin #1 orientation. Possible bad cable.

Check CMOS setup for correct drive

type: 3.5" 1.44 MB.

Attempted to format an HD diskette to

720K or DD diskette to 1.44 MB. Drive

is not properly set in CMOS setup. Or

controller card is not configured

correctly. Check setup by referring to

controller documentation.

Controller is not receiving disk change

signal. Pin #34 on the ribbon cable is

broken. Or disk drive is malfunctioning.

No diskette inserted in the drive or

motor not spinning. Drive may need

service. A possible bad cable.

Diskette not formatted. Drive out of

alignment. DSDD disk formatted to

1.44MB.HD disk formatted for 720K.

Use correct disk. Drive may need service.

Head seek error or drive out of

alignment. Bad media or drive.

Trouble Shooting

Inhaltsverzeichnis

Andere Teac Diskettenlaufwerk Handbücher

Teac

Teac FD-55 Series Bedienungsanleitung

Teac

Teac FD-05PUB Bedienungsanleitung

Teac

Teac FD-55 Series Bedienungsanleitung

Teac

Teac Internal Floppy Drives Bedienungsanleitung

Teac

Teac FD-05PUB Bedienungsanleitung

Teac

Teac FD-05PU Bedienungsanleitung

Teac

Teac FD-55BR-100 Benutzerhandbuch

Teac

Teac FD-55 Series Bedienungsanleitung

Beliebte Diskettenlaufwerk Handbücher anderer Marken

Commodore

Commodore 2031 Bedienungsanleitung

Epson

Epson SMD-100 series Bedienungsanleitung

Bering

Bering OptiPac 2652MD Bedienungsanleitung

EI-EN Enterprise

EI-EN Enterprise Super 5 Bedienungsanleitung

Commodore

Commodore 1581 Bedienungsanleitung

Shugart

Shugart SA410 Bedienungsanleitung

Panasonic

Panasonic CF-VFDU03U - 1.44 MB Floppy Disk Drive Bedienungsanleitung

Cipher Data Products

Cipher Data Products FloppyTape 525 Series Technische Daten

Iomega

Iomega Zip 250 Gebrauchsanweisung

Commodore

Commodore 8050 Bedienungsanleitung

Panasonic

Panasonic CF-VFDU03W Bedienungsanleitung

CORVUS

CORVUS H-Series Bedienungsanleitung

Commodore

Commodore vic-1540 Bedienungsanleitung

Commodore

Commodore 8050 Bedienungsanleitung

Atari

Atari 810 Bedienungsanleitung

Tandon

Tandon TM848-1 Service-Handbuch

Epson

Epson TF-20 Bedienungsanleitung

Siemens

Siemens Microfloppy FDD100-5 Betriebsanleitung