Teac DR-100MKII Bedienungsanleitung

D01160520A

DR-100)"

Linear PCM Recorder

OWNER'S MANUAL

2 TASCAM DR-100MKII

IMPORTANT SAFETY PRECAUTIONS

For U.S.A

TO THE USER

This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful

interference in a residential installation. This equipment

generates, uses, and can radiate radio frequency energy

and, if not installed and used in accordance with the

instruction manual, may cause harmful interference

to radio communications. However, there is no

guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful

interference to radio or television reception, which can

be determined by turning the equipment o and on,

the user is encouraged to try to correct the interference

by one or more of the following measures.

a) Reorient or relocate the receiving antenna.

b) Increase the separation between the equipment and

receiver.

c) Connect the equipment into an outlet on a

circuit dierent from that to which the receiver is

connected.

d) Consult the dealer or an experienced radio/TV

technician for help.

CAUTION

Changes or modications to this equipment not

expressly approved by TEAC CORPORATION for

compliance could void the user's authority to operate

this equipment.

Declaration of Conformity

Model Number : DR-100MKII

Trade Name : TASCAM

Responsible party : TEAC AMERICA, INC.

Address : 7733 Telegraph Road, Montebello,

California, U.S. A.

Telephone number: 1-323-726-0303

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference recieved,

including interference that may cause undesired

operation.

This appliance has a serial number located on the rear

panel. Please record the model number and serial

number and retain them for your records.

Model number

Serial number

For European Customers

Disposal of electrical and electronic equipment

(a) All electrical and electronic equipment should be

disposed of separately from the municipal waste stream

via designated collection facilities appointed by the

government or the local authorities.

(b) By disposing of the electrical and electronic equipment

correctly, you will help save valuable resources and

prevent any potential negative eects on human health

and the environment.

eects on the environment and human health as a

result of the presence of hazardous substances in

electrical and electronic equipment.

(d) The crossed out wheeled dust bin symbol

indicates that electrical and electronic

equipment must be collected and disposed of

separately from household waste.

(e) The return and collection systems are available

to the end users. For more detailed information about

disposal of old electrical and electronic equipment,

please contact your city oce, waste disposal service or

the shop where you purchased the equipment.

Disposal of batteries and/or accumulators

(a) Waste batteries and/or accumulators should be

disposed of separately from the municipal waste stream

via designated collection facilities appointed by the

government or the local authorities.

(b) By disposing of waste batteries and/or accumulators

correctly, you will help save valuable resources and

prevent any potential negative eects on human health

and the environment.

accumulators can have serious eects on the

environment and human health as a result of the

presence of hazardous substances in batteries and/or

accumulators.

(d) The crossed out wheeled dust bin symbol

indicates that batteries and/or accumulators

must be collected and disposed of separately

from household waste.

If the battery or accumulator contains more

than the specied values of lead (Pb), mercury (Hg),

and/or cadmium (Cd) dened in the Battery Directive

(2006/66/EC), then the chemical symbols for lead (Pb),

mercury (Hg) and/or cadmium (Cd) will be indicated

beneath the crossed out wheeled dust bin symbol.

(e) The return and collection systems are available to the

end users. For more detailed information about disposal

of waste batteries and/or accumulators, please contact

your city oce, waste disposal service or the shop

where you purchased them.

Pb, Hg, Cd

TASCAM DR-100MKII 3

IMPORTANT SAFETY INSTRUCTIONS

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in

accordance with the manufacturer's instructions.

8 Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including

ampliers) that produce heat.

9 Do not defeat the safety purpose of the polarized

or grounding-type plug. A polarized plug has two

blades with one wider than the other. A grounding

type plug has two blades and a third grounding

prong. The wide blade or the third prong are

provided for your safety. If the provided plug does

not t into your outlet, consult an electrician for

replacement of the obsolete outlet.

10 Protect the power cord from being walked on

or pinched particularly at plugs, convenience

receptacles, and the point where they exit from the

apparatus.

11 Only use attachments/accessories specied by the

manufacturer.

12 Use only with the cart, stand, tripod, bracket, or

table specied by the manufacturer, or sold with the

apparatus. When a cart is used, use caution when

moving the cart/apparatus combination to avoid

injury from tip-over.

13 Unplug this apparatus during lightning storms or

when unused for long periods of time.

14 Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or

plug is damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus has

been exposed to rain or moisture, does not operate

normally, or has been dropped.

Do not expose this apparatus to drips or splashes.

•

Do not place any objects filled with liquids, such as

•

vases, on the apparatus.

Do not install this apparatus in a confined space such as

•

a book case or similar unit.

The apparatus draws nominal non-operating power

•

from the AC outlet with its POWER or STANDBY/ON

switch not in the ON position.

The apparatus should be located close enough to the

•

AC outlet so that you can easily grasp the power cord

plug at any time.

The mains plug is used as the disconnect device, the

•

disconnect device shall remain readily operable.

If the product uses batteries (including a battery pack

•

or installed batteries), they should not be exposed to

sunshine, fire or excessive heat.

CAUTION for products that use replaceable lithium

•

batteries: there is danger of explosion if a battery is

replaced with an incorrect type of battery. Replace only

with the same or equivalent type.

Caution should be taken when using earphones or

•

headphones with the product because excessive sound

pressure (volume) from earphones or headphones can

cause hearing loss.

4 TASCAM DR-100MKII

8Cautions about rechargeable batteries

This product uses rechargeable batteries. Misuse of

batteries could cause a leak, rupture or other trouble.

Always abide by the following precautions when using

batteries.

If a rechargeable battery leaks, do not touch the

•

leaking fluid with a bare hand. Please consult with TEAC

Corporation if a battery fluid leak occurs.

Battery fluid in an eye could result in loss of vision. If

•

fluid enters an eye, wash the eye immediately with clean

water. Do not rub the eye when washing. Consult a

physician soon after washing. Battery fluid on the body

or clothing could cause injuries or burns on the skin.

Wash with clean water immediately and then consult a

physician.

Do not use any AC adaptor other than the model

•

designated for use with this unit. Always use the

designated AC adaptor when operating the unit or

recharging the battery with a household AC power

source. Use of an AC adaptor other than the designated

one could lead to overheating and cause injury, burns,

fires or stains, as well as battery ruptures and battery

fluid leaks.

Do not put a battery into a fire or leave it or recharge it

•

near a fire, under the sun or in other hot conditions.

Do not disassemble a battery. Doing so could cause

•

electric shock. Please contact the shop where you

bought the product or TEAC Corporation if you want to

have a battery inspected or repaired. When you want to

dispose of the product, please follow the instruction in

the Owner's Manual to remove the batteries and recycle

the equipment properly.

Cautions about batteries

Never recharge non-rechargeable batteries. The

•

batteries could rupture or leak, causing fire or injury.

When installing batteries, pay attention to the polarity

•

indications (plus/minus (+/–) orientation), and install

them correctly in the battery compartment as indicated.

Putting them in backward could make the batteries

rupture or leak, causing fire, injury or stains around

them.

When you store or dispose batteries, isolate their terminals

•

with insulation tape or something like that to prevent them

from contacting other batteries or metallic objects.

When throwing used batteries away, follow the disposal

•

instructions indicated on the batteries and the local

disposal laws.

Small children may mistakenly swallow a lithium coin

•

battery and it is very dangerous. Keep the battery and

the remote control out of the reach of small children. In

the event a battery is swallowed, immediately consult a

physician.

Do not use batteries other than those specified. Do not

•

mix and use new and old batteries or different types of

batteries together. The batteries could rupture or leak,

causing fire, injury or stains around them.

Do not carry or store batteries together with small metal

•

objects. The batteries could short, causing leak, rupture

or other trouble.

Do not heat or disassemble batteries. Do not put them

•

in fire or water. Batteries could rupture or leak, causing

fire, injury or stains around them.

If the battery fluid leaks, wipe away any fluid on the

•

battery case before inserting new batteries. If the battery

fluid gets in an eye, it could cause loss of eyesight. If

fluid does enter an eye, wash it out thoroughly with

clean water without rubbing the eye and then consult a

doctor immediately. If the fluid gets on a person’s body

or clothing, it could cause skin injuries or burns. If this

should happen, wash it off with clean water and then

consult a doctor immediately.

Remove the batteries if you do not plan to use the unit

•

for a long time. Batteries could rupture or leak, causing

fire, injury or stains around them. If the battery fluid

leaks, wipe away any fluid on the battery compartment

before inserting new batteries.

Do not disassemble a battery. The acid inside the battery

•

could harm skin or clothing.

This Product contains a CR Coin Lithium Battery which

contains Perchlorate material - special handling may

apply.

See www.dtsc.ca.gov/hazardouswaste/perchlorate

Safety Information

For China

TASCAM DR-100MKII 5

Contents

IMPORTANT SAFETY PRECAUTIONS ..................... 2

IMPORTANT SAFETY INSTRUCTIONS .................... 3

Safety Information ................................................. 4

Quick Start Guide ................................................... 7

1 – Introduction ...................................................... 9

Main features.................................................................................9

Included items ..............................................................................9

Conventions used in this manual ..........................................9

Recycling the lithium ion battery ....................................... 10

Intellectual property rights................................................... 10

SD cards........................................................................................ 11

Precautions for use .............................................................. 11

Precautions for placement and use ...................................11

Beware of condensation ........................................................ 11

Cleaning the unit ...................................................................... 11

User registration........................................................................ 11

2 – Names and Functions of Parts ....................... 12

Top pane ...................................................................................... 12

Front panel.................................................................................. 13

Rear panel.................................................................................... 13

Left side panel............................................................................ 14

Right side panel......................................................................... 14

Bottom panel ............................................................................. 14

Remote control (TASCAM RC-10)........................................ 15

Home screen............................................................................... 16

Recording screen ...................................................................... 17

Menu item list ............................................................................ 18

Using menus............................................................................... 18

Basic operation.......................................................................... 19

3 – Preparation for Use......................................... 20

Preparing the power................................................................ 20

Power source options......................................................... 20

Using the lithium ion battery........................................... 20

Using AA batteries............................................................... 20

Using both types of batteries together........................ 20

Using an AC adaptor (sold separately) ......................... 21

Using an external battery pack (sold separately) ..... 21

Preparing the remote control............................................... 21

Installing the battery ......................................................... 21

When to change the battery............................................ 21

Cautions about the use of the battery .........................21

Using the remote control (TASCAM RC-10)..................... 22

Wireless use ........................................................................... 22

Wired use ................................................................................ 22

Enable wired remote control use .................................. 22

Precautions for use of the remote control .................. 22

Turning the power on and off.............................................. 23

Starting up the unit............................................................. 23

Shutting down ...................................................................... 23

Battery settings ......................................................................... 23

Setting the date and time...................................................... 23

Inserting and removing SD cards ....................................... 24

Inserting the card................................................................. 24

Removing the card .............................................................. 24

SD card write protection ................................................... 24

Preparing an SD card for use ................................................ 24

Using the built-in speaker ..................................................... 25

Connecting monitors and headphones ........................... 25

Mode selection .......................................................................... 25

Setting the mode ................................................................. 25

Confirming the mode ....................................................... 25

Restrictions when using HS mode ............................... 26

4 – Recording ........................................................ 27

Setting the mode ..................................................................... 27

Selecting file format, sampling frequency, and

maximum file size..................................................................... 27

Available recording time display.................................... 27

Setting where files are saved................................................ 28

Setting the analog input........................................................ 28

Recording with the built-in mics (UNI/OMNI)............ 28

Recording with external mics (XLR)............................... 28

Using phantom power ...................................................... 29

Recording from external equipment (LINE 1)............ 29

Recording from external equipment (LINE 2)............ 29

Setting the digital input......................................................... 30

Making analog input settings ............................................. 30

Adjusting the analog input level......................................... 31

Manually adjusting the analog input level................. 31

Using the level control function ................................... 32

Recording .................................................................................... 32

Dividing files and creating new files while recording . 33

Creating new files manually while recording (track

incrementing)........................................................................ 33

Creating new files automatically while recording

(automatic track incrementing) ...................................... 33

Automatically cutting silences during recording..... 33

Dividing a file manually (DIVIDE) ........................................ 33

Recording playback and input sounds together

(overdubbing)............................................................................ 34

Select the file you want to overdub .............................. 34

Monitoring input signals .................................................. 34

Adjusting the input and playback sound levels........ 34

Recording an overdub........................................................ 34

Automatic recording (AUTO REC) ....................................... 35

Enabling automatic recording......................................... 35

Automatically adding marks when recording

(MARK)...................................................................................... 35

Automatically pausing recording (PAUSE) .................. 36

Start new files automatically during recording (TRK

INC)............................................................................................ 36

Mark function............................................................................. 36

Adding marks manually during recording and

playback .................................................................................. 36

Moving to a mark position................................................ 37

Clearing Marks ...................................................................... 37

Recording the moment before pushing RECORD (PRE

REC)................................................................................................ 37

Delaying the start of recording (REC DELAY).................. 37

Recording duration.................................................................. 38

5 – Working with Files and Folders (BROWSE

Screen) ............................................................. 39

Screen navigation..................................................................... 39

6 TASCAM DR-100MKII

Contents

Icons on the BROWSE screen................................................ 39

File operations ........................................................................... 39

Folder operations...................................................................... 40

Add identification tags to files (QUICK TAG) ................... 40

Delete the selected file (QUICK DEL) ................................. 41

6 – Playback .......................................................... 42

Selecting files for playback (skip)........................................ 42

Setting the mode...................................................................... 42

Adjusting playback volume .................................................. 42

Setting the playback area (AREA) ....................................... 42

Selecting a folder for the playback area (1)..................... 42

Selecting a folder for the playback area (2)..................... 43

Playlist........................................................................................... 43

Adding files to the playlist................................................ 43

Editing the playlist............................................................... 43

Selecting files for playback (skip)........................................ 44

Playback ....................................................................................... 44

Stopping ...................................................................................... 44

Pausing (PAUSE) ........................................................................ 44

Rewinding and fast-forwarding (search).......................... 44

Using the wheel to change the playback position .. 45

Repeat playback (REPEAT)..................................................... 45

Loop playback............................................................................ 45

Special playback control functions .................................... 45

Setting the playback control functions........................ 45

Changing speed without changing pitch (VSA

function).................................................................................. 46

Changing playback speed ............................................... 46

7 – Connecting with a Computer ......................... 47

Connecting a computer ......................................................... 47

Transferring files to a computer .......................................... 47

Transferring files from a computer..................................... 47

Disconnecting from a computer......................................... 47

Using the INFORMATION screens........................................ 48

File information page (FILE) ............................................. 48

Card information page (CARD)........................................ 48

System information page (SYSTEM).............................. 48

8 – Settings and Information ............................... 48

Battery information page (BATTERY)............................ 49

Operation settings (SETUP) .................................................. 49

Search speed setting ......................................................... 49

Automatic power OFF setting ........................................ 49

Automatic backlight OFF setting .................................. 49

Display contrast setting .................................................... 49

Backlight brightness setting ........................................... 49

Restoring default settings ................................................ 49

Using QUICK FORMAT......................................................... 50

Using FULL FORMAT............................................................ 50

Setting the main battery source (MAIN)........................... 50

Changing batteries when the power is on.................. 50

Setting the type of AA batteries (AA BATTERY) ............. 51

Setting the file name format................................................. 51

File name format ..................................................................51

Setting the file name (WORD) ......................................... 51

9 – Using the REMOTE/DIGITAL IN jack ............... 52

Footswitch (TASCAM RC-3F, sold separately) ................. 52

Setting footswitch operation........................................... 52

Using the footswitch........................................................... 52

Using digital input.................................................................... 52

Setting the digital input ..................................................52

10 – Messages ....................................................... 54

11 – Troubleshooting ........................................... 56

12 – Specifications................................................ 57

Ratings.......................................................................................... 57

Input/output ratings................................................................ 57

Analog audio input/output ratings............................... 57

Digital audio input ratings................................................ 57

Control input/output ratings........................................... 57

Audio performance.................................................................. 57

Requirements for connected computers......................... 57

General ......................................................................................... 58

Dimensional drawing.............................................................. 58

TASCAM DR-100MKII 7

Quick Start Guide

In this section, we explain how to use this unit to record

with the built-in mics (UNI MIC) and how to play back a

recording.

The unit contains a factory-installed SD card, and will by

default produce 44.1 kHz, 16-bit WAV les.

Higher-quality or longer les can be produced using other

recording settings. See “Selecting file format, sampling

frequency, and maximum file size” for details on page 27.

1 Insert the included TASCAM BP-L2 lithium ion

battery into the battery compartment on the side of

the recorder. Orient the battery so that it fits in the

battery compartment.

NOTE

When the product is purchased new, the included TASCAM

BP-L2 lithium ion battery has not been charged suciently

for the operation of the recorder. Charge the battery before

using the unit by connecting it with a computer by USB.

(See “Using the lithium ion battery” on page 20.)

2 Turn on, and various setting information will be

displayed.

Press the button on the left side panel until the

unit is turned on, and then release it.

NOTE

After purchasing the recorder, the rst time you turn the

power ON, the

DATE/TIME

screen will open in order to

enable it to accurately add date and time information to

recorded les.

Press the .or /button to move the cursor

(highlighted portion), and adjust the date and time using

the wheel. Then press the ENTER/MARK button to set. (See

“Setting the date and time” on page 23.)

3 Set the INPUT switch to UNI.

4 Press the RECORD [0] button to switch to recording

standby. The indicator will flash.

RECORD button/

indicator

5 Use the INPUT knob on the right side panel to adjust

the analog input level. See“Adjusting the analog

input level”on page 31 for details.

6 Press the RECORD [0] button to start recording. The

indicator will light during recording.

7 Press the STOP [8] button to finish recording.

NOTE

To pause recording, press the RECORD [0]or PLAY/

PAUSE [7/9] button. Press the RECORD [0]or PLAY/

PAUSE [7/9] button again to restart recording in the

same le.

8 TASCAM DR-100MKII

8 Press the PLAY/PAUSE [7/9]button for playback.

If you use a headphone or external monitor system

(powered monitor speakers or amplifier and

speakers), connect it to the or LINE OUT jack on the

left side panel.

Powered monitor speakers

or amplier and speakers

Headphones

For playback over the built-in speaker, turn the

SPEAKER switch to ON (See “Using the built-in

speaker” on page 25.)

NOTE

When headphones are connected, sound will not be

output from the speaker even if the SPEAKER switch is ON.

9 Use the /SP OUTPUT volume control to adjust the

playback volume.

10 Press the STOP [8] button to stop playback.

NOTE

If you have made several recordings, use the .or /

button to select the le to play when playing back or

stopped and the Home Screen is displayed.

11 To turn the power OFF, press and hold the

button on the left side panel until

LINEAR PCM

RECORDER

appears on the screen. When the recorder

is finished shutting down, the power will turn off.

Quick Start Guide

TASCAM DR-100MKII 9

1 – Introduction

Thank you very much for purchasing a TASCAM DR-100MKII

Linear PCM Recorder.

Before using your unit, please read this manual carefully so

that you will understand the correct operating procedures

and be able to use all the functions fully. We hope that you

will enjoy using this product for many years to come.

Please keep this manual for future reference. You can also

download a digital copy from our website (http://tascam.

com/).

Main features

Uses SD/SDHC cards as storage media for high quality

•

audio recording

Includes HS mode that supports 44.1 kHz, 48 kHz and

•

96 kHz sampling frequencies and allows recording and

playback at 96 kHz

Linear PCM (WAV format) recording possible at 44.1 kHz,

•

48 kHz or 96 kHz and 16-bit or 24-bit (96 kHz supported

only in HS mode)

MP3 format recording possible at 32–320 kbps (STD

•

mode, ID3 tag v2.4 supported)

4 total built-in mics include 2 directional mics suitable

•

for high-quality stereo recording and 2 omnidirectional

mics optimal for recording meetings and similar events

2 lockable XLR mic connectors that can provide +48V

•

phantom power

Built-in 0.4-W mono speaker

•

2 different types of batteries used together allow for

•

many hours of operation as well as the ability to change

batteries while recording

AUTO REC function allows the unit to start and stop

•

recording automatically by sensing changes in the

analog input level

MARK function allows you to move to specific locations

•

in a recording

DIVIDE function allows you to split a file at the position

•

you select (WAV files only)

PRE REC function allows the unit to record the two

•

seconds of sound before recording is activated (pre-

recording)

User words and dates can be set for file names

•

Quick Tag function allows you to quickly identify files

•

REC DELAY allows you to avoid recording the sound of

•

pushing the RECORD [0] button

Automatic track incrementing creates a new file and

•

continues recording when a file size or input level set in

advance is exceeded

Track incrementing allows the creation of new files at

•

any time during recording without pausing

Tripod mounting hole built-in

•

Wireless remote control (TASCAM RC-10) included with

•

wired remote control adapter and cable

USB cable, soft case and windscreen included

•

3.5 mm (1/8”) line/headphones output jack

•

128 x 64 pixel LCD with backlight

•

Mini-B type USB 2.0 port

•

Power can be supplied using a TASCAM BP-6AA external

•

battery pack, which meets the specifications of this unit

(sold separately)

Included items

This product includes the following items.

Take care when opening the package not to damage the

items. Keep the package materials for transportation in the

future.

Please contact the retailer where you purchased this unit

if any of these items are missing or have been damaged

during transportation.

Main unit

•......................................................................................... 1

SD memory card (installed in the main unit)

•..................... 1

TASCAM BP-L2 custom lithium ion battery (including

•

warranty and manual) ................................................................1

USB cable (80 cm)

•......................................................................... 1

Soft case

•.......................................................................................... 1

Windscreen

•..................................................................................... 1

TASCAM RC-10 Wireless remote control

•.............................. 1

Coin battery for remote control (installed in remote

•

control)............................................................................................. 1

Wired remote control adapter

•................................................. 1

Wired remote control cable

•...................................................... 1

Digital conversion cable

•............................................................ 1

Warranty

•.......................................................................................... 1

Owner’s manual (this document)

•........................................... 1

Conventions used in this manual

The following conventions are used in this manual.

Buttons and connectors on this device are indicated like

•

this: MENU

Messages on the unit’s screen are shown like this:

•

Messages that appear on the computer’s screen are

•

shown like this: DR-100MKII

“SD memory card” is sometimes abbreviated as“SD

•

card.”

Additional information is provided as necessary as “tips,”

•

“notes” and “cautions.”

TIP

These are tips about how to use the unit.

NOTE

These provide additional explanations and describe special

cases.

CAUTION

Failure to follow these instructions could result in injury,

damage to equipment or lost recording data, for example.

10 TASCAM DR-100MKII

1 – Introduction

Recycling the lithium ion battery

This unit uses a lithium ion battery. When you no longer

need the battery please help preserve the valuable

resources it contains by returning it to a business that

recycles rechargeable batteries.

Please contact a TASCAM sales representative if you have

any questions.

Li-ion00

Intellectual property rights

TASCAM is a registered trademark of TEAC Corporation.

•

SDHC Logo is a trademark of SD-3C, LLC.

•

Supply of this product does not convey a license nor

•

imply any right to distribute MPEG Layer-3 compliant

content created with this product in revenue-generating

broadcast systems (terrestrial, satellite, cable and/or

other distribution channels), streaming applications (via

Internet, intranets and/or other networks), other content

distribution systems (pay-audio or audio-on-demand

applications and the like) or on physical media (compact

discs, digital versatile discs, semiconductor chips, hard

drives, memory cards and the like). An independent

license for such use is required. For details, please visit

http://mp3licensing.com.

MPEG Layer-3 audio coding technology licensed from

•

Fraunhofer IIS and Thomson.

Microsoft, Windows, Windows XP, Windows Vista,

•

and Windows 7 are either registered trademarks or

trademarks of Microsoft Corporation in the United

States and/or other countries.

Apple, Macintosh, iMac, Mac OS and Mac OS X are

•

trademarks of Apple Inc.

Other company names, product names and logos in this

•

document are the trademarks or registered trademarks

of their respective owners.

Any data, including, but not limited to information,

described herein are intended only as illustrations

of such data and/or information and not as the

specications for such data and/or information. TEAC

Corporation disclaims any warranty that any use

of such data and/or information shall be free from

infringement of any third party’s intellectual property

rights or other proprietary rights, and further, assumes

no liability of whatsoever nature in the event of any

such infringement, or arising from or connected with or

related to the use of such data and/or information.

This product is designed to help you record and

reproduce sound works to which you own the

from the copyright holder or the rightful licensor.

Unless you own the copyright, or have obtained the

appropriate permission from the copyright holder

or the rightful licensor, your unauthorized recording,

reproduction or distribution thereof may result in

severe criminal penalties under copyright laws and

international copyright treaties. If you are uncertain

about your rights, contact your legal advisor. Under no

circumstances will TEAC Corporation be responsible

for the consequences of any illegal copying performed

using the recorder.

Inhaltsverzeichnis

Andere Teac Diktiergerät Handbücher

Teac

Teac RW-800 Bedienungsanleitung

Teac

Teac WX-7000 Bedienungsanleitung

Teac

Teac 80-8 Bedienungsanleitung

Teac

Teac SD-500HR Bedienungsanleitung

Teac

Teac VR-10 Bedienungsanleitung

Teac

Teac DR-2d Bedienungsanleitung

Teac

Teac WX Navi Bedienungsanleitung

Beliebte Diktiergerät Handbücher anderer Marken

Sony

Sony ICD-UX533F Bedienungsanleitung

RCA

RCA VR5230 Bedienungsanleitung

Ramsey Electronics

Ramsey Electronics BULLSHOOTER ENDLESS LOOP BS2C Benutzerhandbuch

Sony

Sony TCM-400DV Bedienungsanleitung

LogTag

LogTag TREL30-16 Bedienungsanleitung

SVAT

SVAT CVP800 Bedienungsanleitung

Marantz

Marantz PMD620 Bedienungsanleitung

Zoom

Zoom H4next Bedienungsanleitung

Roland

Roland BR-900CD Bedienungsanleitung

JVC

JVC ProHD GY-HMZ1U Bedienungs- und Wartungshandbuch

Panasonic

Panasonic PQT8531-P Bedienungsanleitung

Sanyo

Sanyo TRC-6400 Bedienungsanleitung

Tascam

Tascam DR-07 Bedienungsanleitung

Olympus

Olympus DW-90 Bedienungsanleitung

Sanyo

Sanyo ICR-B150 Bedienungsanleitung

Korg

Korg D4 Bedienungsanleitung

Sony

Sony ICD-SX46 - Ic Recorder Bedienungsanleitung

Olympus

Olympus DIGITAL VOICE RECORDER WS-200S Montageanleitung