TEC ST-6500 Bedienungsanleitung

ST-6500 Setup Guide for Windows

TOSHIBA TEC CORPORATION

Windows Setup Guide for ST-6500/ST-6500-C7

TOSHIBA TEC CORPORATION

1. Introduction

This setup guide describes the procedure and notes for installing the drivers on the

ST-6500/ST-6500-C7.

The procedure outline to set up the OS for the ST-6500/ST-6500-C7 is described below. Some

drivers supported by some OS will be automatically installed, when the OS is installed.

Procedure outline to set up the ST-6500/ST-6500-C7 on Windows

1) Setting up BIOS

2) Installing Windows

3) Installing the 810E2 chipset software

4) Installing the SM712 graphic driver (for the ST-6500-C7)

5) Installing the PnP touch panel driver

6) Changing the serial port setting

Windows Setup Guide for ST-6500/ST-6500-C7

TOSHIBA TEC CORPORATION

2. Setup on Windows 98/Windows 98SE

1) Setting up BIOS

By pressing the F2 key on the keyboard, when the machine starts up, the BIOS Setup Menu

is selected. Select the following item for BIOS setup.

[Exit]-> Load Setup Defaults (Win98/Me)

2) Installing Windows

Install Windows 98 or Windows 98SE.

3) Installing the 810E2 Chipset Software

wInstalling the Intel Chipset Installation Utility

Execute Chipset¥Chipset¥Disk1¥Setup.exe contained in the driver kit, and install “Intel

Chipset Installation Utility.”

wInstalling the Intel 810/815 Chipset Family Graphics Driver

To enable the CRT display, this driver must be installed.

Execute Chipset¥Graphics¥Win9x¥Graphics¥Setup.exe contained in the driver kit, and

install “Intel 810/815 Chipset Family Graphics Driver.”

wInstalling the Intel®PRO/100 VE Network Connection Driver

Execute Chipset¥LAN¥100pdisk.exe contained in the driver kit, to extract the files onto the

hard disk. Select [PCI Ethernet Controller] in the Device Manager and click on the

“Properties”button.

Windows Setup Guide for ST-6500/ST-6500-C7

TOSHIBA TEC CORPORATION

The following screen appears. Select “Reinstall Driver”to install the driver.

Select the folder to extract 100pdisk.exe to, as the folder containing the driver to be installed.

Select “Intel®PRO/100 VE Network Connection”to install the driver.

For detailed installation procedure, refer to Intel’s documents and online help.

Windows Setup Guide for ST-6500/ST-6500-C7

TOSHIBA TEC CORPORATION

4) Installing the SM712 Graphic Driver

Select [Display] on the Control Panel and display the “Display Properties”screen. On this

screen, select [Settings] –[Advanced] to display the “Standard PCI Graphics Adapter

Properties”screen. Select [Adapter] –[Change] on this screen. Select

“Display¥SM712¥Win98”in the driver kit to install“Silicon Motion LynxEM+.”

5) Installing the CHIPS Graphic Driver

Select [Display] on the Control Panel and display the “Display Properties”screen. On this

screen, select [Settings] –[Advanced] to display the “Standard PCI Graphics Adapter

Properties”screen. Select [Adapter] –[Change] on this screen. Select

“Display¥Chips¥Win98”in the driver kit to install “Chips And Technologies, Accelerator.”

Windows Setup Guide for ST-6500/ST-6500-C7

TOSHIBA TEC CORPORATION

6) Installing the PnP Touch Panel Driver

Select “SMK PnP TABLET”in the Device Manager, and click on the “Properties”button. On

the “SMK PnP TABLET properties”screen, select [General] –[Reinstall Driver] to install the

driver.

Select “Tablet¥PnPTablet¥Win9x”in the driver kit to install “SMK PnP Tablet Driver.”

Reboot the machine. Select [Touch Panel] on the Control Panel to display the “Touch Panel

Property”screen. On this screen, select [Calibration] –[Execute] to set up calibration.

Windows Setup Guide for ST-6500/ST-6500-C7

TOSHIBA TEC CORPORATION

IMPORTANT:

*Unless any of the PS/2 mouse, the serial mouse, or the USB mouse is used, the

touch panel is not detected. When installing the driver, connect any of the mice

and let the machine detect the touch panel.

*Do not check the “Beep when touched”checkbox on the Sound tab page.

This function is not available on Windows 98. (Windows 98 cannot keep the

sound constant.)

7) Changing the Serial Port Setting

IRQ for COM4 has been set incorrectly. Change the IRQ to “11.”No additional operation

for the SIO1 port is required, since it cannot be actually used due to hardware configuration.

Windows Setup Guide for ST-6500/ST-6500-C7

TOSHIBA TEC CORPORATION

8) Setting up the Dual Display

To enable the dual display, carry out this setup.

The ST-6500-C7 enables the dual display using the Dual Display functions supported by

Windows.

Select [Display] on the Control Panel to display the “Display Properties”screen. On this

screen, select [Settings] –[Display]. Select the on-board VGA (Intel810E2)-equipped

display. Check the “Extend my Windows desktop onto this monitor”checkbox at the lower

left, then click on the “Apply”button. The on-board VGA will be enabled.

Select proper “Colors”and “Screen area”.

IMPORTANT:

*Windows 98/98SE/2000/XP can use the Dual Display functions supported by the

OS. However, Windows NT cannot use the Dual Display functions, since

Windows NT does not support them.

Windows Setup Guide for ST-6500/ST-6500-C7

TOSHIBA TEC CORPORATION

IMPORTANT:

*If the SM712 VGA board (SMI) has been inserted on the machine, when Windows

98 is installed, the on-board VGA (Intel810E2) cannot be used after Windows 98

has been installed. On the “Device Manager”tab of the “System Properties”

screen, the on-board VGA (Intel810E2) is marked with “!”, which indicates the

device is disabled. (See the screen below.)

To solve this problem, remove the SM712 VGA board from the machine, then

start up the PC. It will make the on-board VGA (Intel810E2) enabled.

Windows Setup Guide for ST-6500/ST-6500-C7

TOSHIBA TEC CORPORATION

9) Cautions of dual-screen use by Windows98 and Windows98SE.

If a dual-screen is set up by Windows 98 and Windows 98SE, an error may occur. iIn order

to set up a dual-screen without generating an error, please set up the follows;

Settings tab of Display Properties Control Panel.

When screen is in the state of disable, as shown in a figure, it is displayed faintly.

A second screen can be enabled by clicking the second display of a figure.

And then the following message boxes are displayed, choose Yes.

Dieses Handbuch passt für folgende Modelle

Andere TEC Touch-Terminal Handbücher

TEC

TEC ST-71 SERIES Bedienungsanleitung

Beliebte Touch-Terminal Handbücher anderer Marken

Ingenico

Ingenico AXIUM EX4000 Bedienungsanleitung

Heisei Electronics

Heisei Electronics Q-POS 815 Bedienungsanleitung

Amano

Amano MTX-15 Bedienungsanleitung

FLOWBIRD

FLOWBIRD CWT Compact Touch Bedienungsanleitung

Demco

Demco SP7 Bedienungsanleitung

Lathem

Lathem PC600 Series Bedienungsanleitung

Partner

Partner MF-2352 Bedienungsanleitung

NCR

NCR RealPOS 7460-2 Handbuch

Simrad

Simrad MS50 Montageanleitung

Unitech

Unitech MR350 MKII Kurzanleitung

Jungheinrich

Jungheinrich WMT 210 Bedienungsanleitung

Motorola

Motorola MTP850 Bedienungsanleitung

YASKAWA

YASKAWA 62H-MDC0 Bedienungsanleitung

MVG industries

MVG industries NeptuLink Bedienungsanleitung

Price Industries Limited

Price Industries Limited FDC Gebrauchsanweisung

Honeywell

Honeywell TemaKey Bedienungsanleitung

EBN

EBN BPC65-B-A16G Bedienungsanleitung

Prestel

Prestel VCS-G2PRO Bedienungsanleitung