TECHCON SYSTEMS TS5624DMP Bedienungsanleitung

Techcon Systems

TS5624DMP

Disposable Material Path

Diaphragm Valve

User Guide

CONTENTS

Page number

1. Specifications…………………..………………………………….…………

2. Unpacking and Inspection……………………………………………………

3. Description...…………………………………………………….….………...

4. Theory of Operation…………………………………………….….…………

5. Setup Instructions……………………………………………….….…………

6. Typical System Set-Up……………………..……..…….……….……………

7. Disposable Material Path Removal/Replacement….………………………….

8. Maintenance of Air Cylinder O-Ring…………………………………………

9. Spare Parts…………………………………………………………………...

10. Accessories…………………………………………………………………..

11. Troubleshooting……………………………………………………………...

12. Warranty……………………………………………………………………..

1. SPECIFICATIONS

TS5624DMP

Size

See below illustration

Weight

0.25 lb. (113g)

Fluid Inlet Port

Luer lock female

Fluid Outlet Port

Luer lock male

Air Inlet Port

10-32 UNF

Auxiliary Air Inlet Port

10-32 UNF

Minimum Air Pressure

70 psi (4.8bar)

Maximum Fluid Pressure

60 psi (4.1bar)

Operating Frequency

Exceeds 400 cycles/min.

Mounting Port

10-32 UNF

Wetted Parts

Black Polyethylene Compound.

Black Nylon (Elbow).

Figure 1.0

Dimensions are in inches [mm]

2. UNPACKING AND INSPECTION

Carefully unpack the valve and examine the items contained in the carton. These

will include:

Valve assembly.

Mounting bracket and mounting screw.

1 x Disposable Material Path.

2 x Hex keys (1/8” & 9/64”).

Sample tip kit.

Fluid line and air hose.

User guide.

3. DESCRIPTION

The TS5624DMP Diaphragm Valve is designed to dispense low to medium

viscosity fluids. An internal spring return makes the valve fully adaptable for use

with any time/pressure controller. A short opening stroke provides extremely fast,

positive shut-off. An external stroke control adjustment makes it easy to fine tune

shot sizes. The TS5624DMP Diaphragm Valves compact design allows for

mounting flexibility and easy integration into automated applications.

4. THEORY OF OPERATION (Refer to figure 2.0)

The TS5624 Diaphragm Valve is normally closed, adjustable stroke valve. Input

air pressure of 70-90 psi (4.8 to 6.2bar) through air inlet port (1) drives the piston

assembly (2) back, opening the material path, allowing fluid flow from the

material inlet (3) to the material outlet (4). Relieving the input air pressure allows

the piston return spring (5) to close the diaphragm (6), ensuring rapid “fail-safe”

shut-off of fluid flow.

Figure 2.0

5. SETUP INSTRUCTIONS

Refer to Figure 3.0

Note: This installation uses Luer lock adapters shipped with the valve.

1. Connect the fluid feed tube or syringe to the fluid inlet port (1).

2. Connect the valve airline to the valve controller or other pneumatic device

that is used to control the valve.

3. Connect the opposite end of the airline to valve air inlet (2).

4. Connect appropriate dispensing tip or nozzle to the fluid outlet port (3).

5. Set the valve controller pressure at 70 psi (4.8bar).

6. Set the fluid pressure. Do not exceed 60 psi (4.1bar).

7. Make sure all connections are tight.

8. Place container under the outlet and activate the valve until the fluid flows

steady.

The amount of fluid that flows through the valve is determined by:

Valve open time

Fluid reservoir pressure

Dispensing tip size

Stroke adjustment knob position

Figure 3.0

6. TYPICAL SYSTEM SET-UP

Figure 4.0

Figure 5.0

Optional Syringe Feeding

1. Attach 7509-9100 syringe bracket as shown below.

2. Use insert rings for syringe sizes 3cc –10cc.

3. Ensure syringe is under constant air pressure.

7. DISPOSABLE MATERIAL PATH REMOVAL/REPLACEMENT:

Removal of a feed path assembly: Refer to figure 6.0

1. Release fluid pressure.

2. Remove syringe barrel or fluid line from the valve.

3. Loosen the lower receiver screws (4 - 5 turns) and pull out disposable material

path.

4. Dispose of the used feed path assembly in an appropriate waste container.

Installation of a new feed path assembly: Refer to figure 6.0

1. Insert a new feed path assembly into the valve housing. Ensure correct fitment

into the actuator.

2. Tighten lower receiver screws to torque setting specified below.

Torque Specifications

14 in lb. (1.58 N-m)

Figure 6.0

1. Loosen screws

4 - 5 turns.

2. Remove DMP

insert.

3. Insert new

DMP insert.

4. Tighten screws

evenly to torque

setting.

8. MAINTENANCE OF AIR CYLINDER O-RING (Refer to figure 7.0 and 8.0)

1. Unscrew receiver screws (1).

2. Remove the DMP (2).

3. Remove the stroke control knob (3) and spring (4).

4. Remove the receiver assembly (5).

5. Remover actuator (6).

6. Remove retaining ring (7), anti-rotate washer (8) and Mylar washer (9).

7. Remove piston (10) from air cylinder (11).

8. Replace O-ring (12) if damaged; otherwise lubricate O-ring with Bimba

HT-99, or equivalent.

9. Reinstall piston (10), retaining ring (7), anti-rotate washer (8) and Mylar

washer (9).

10. Reinstall actuator (6) as per position in Step 4. 90° offset to the air inlet.

11. Reinstall receiver assembly (5), leaving receiver screws loose.

12. Reinstall spring (4) and stroke control knob (3).

13. Install DMP (2) and set torque on receiver screws. - 14 in lb. (1.58 N-m)

Vertical slot must

face this way, 90°

offset to the air inlet.

Step 1

Figure 7.0

(12)

(10)

(1)

(2)

(3)

(4)

(5)

(6)

(7)

(8)

(10)

(11)

(9)

Step 2

Step 3

Step 6

Step 5

Step 4

9. SPARE PARTS

ITEM

PART NUMBER

DESCRIPTION

5620-000-004

End Cap

TSD1400-111APK

End Cap O-Ring (Pack of 10)

2800-0892

Washer, SS

3300-0578

Spring

TSD1120-11

Retaining Ring

TSD1109-43

Mylar Washer

5620-000-006

Anti-Rotate Washer

TSD1400-016APK

Piston O-Ring (Pack of 10)

5620-000-005

Piston

5620-000-003

Air Cylinder

A0100478

Air Hose/Connector Assembly, 4mm

TSD1003-20

Air Fitting, 4mm, Elbow

7509-0250

Actuator

7509-0270

Upper Receiver

2800-0463

Upper Receiver Screw

7509-0280

Lower Receiver

2800-0236

Washer

2800-0886

Screw

DMP-5624

Disposable Material Path (Pack of 10)

TSD1106-13

Mounting Screw

918-000-048

Mounting Bracket

7509-9100

Syringe Bracket W/Inserts (See Fig.5)

Lubrication: All O-Rings must be lubricated with Bimba HT-99, or equivalent.

Receiver Mounting Screws Torque (Item 18): 14 in lb. (1.58 N-m).

Figure 8.0

10. ACCESSORIES

10.1 FLUID FITTINGS AND TUBING

10.2 BRACKETS

PART NUMBER

DESCRIPTION

TS918-46

4-Way Fluid Manifold

TN00DKIT

Complete Dispensing Tip Kit

9000-000-100

Sample Tip Kit

PART NUMBER

DESCRIPTION

TSD1003-16

⅛'' NPT to ¼'' O.D. Tube, 90° Elbow

TSD1002-17

⅛'' NPT to ⅜'' O.D. Tube

TSD1002-18

⅛'' NPT to ¼'' O.D. Tube

TSD1002-38

¼'' NPT to ¼'' O.D. Tube

TSD1099-22

⅜'' O.D. X ¼'' I.D. Tube, Black, Polyethylene

TSD1099-23

⅜'' O.D. X ¼'' I.D. Tube, Clear, Polyethylene

TSD1099-24

¼'' O.D. X ⅛'' I.D. Tube, Clear, Polyethylene

TSD1099-25

¼'' O.D. X ⅛'' I.D. Tube, Black, Polyethylene

TSD1099-45

6mm O.D. X 4mm I.D, Clear, Polyethylene

TSD1099-46

6mm O.D. X 4mm I.D, Black, Polyethylene

TSD126-360BPK

Luer Lock Tubing, 60'' (1524mm) , Black

PART NUMBER

DESCRIPTION

918-033-000

Productions Master Stand (Base & Support)

918-000-012

Rod Clamp Assembly

5620-000-008

4'' (101.6mm) Threaded Mounting Rod

7509-9100

Syringe Bracket With Inserts

Inhaltsverzeichnis

Andere TECHCON SYSTEMS Steuereinheit Handbücher

TECHCON SYSTEMS

TECHCON SYSTEMS TS5620 Series Bedienungsanleitung

TECHCON SYSTEMS

TECHCON SYSTEMS TS5440 Bedienungsanleitung

TECHCON SYSTEMS

TECHCON SYSTEMS TS9800 Series Bedienungsanleitung

TECHCON SYSTEMS

TECHCON SYSTEMS TS941 Bedienungsanleitung

TECHCON SYSTEMS

TECHCON SYSTEMS TS5322 Bedienungsanleitung

TECHCON SYSTEMS

TECHCON SYSTEMS TS924 Installationshandbuch

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung