Techko S082K Bedienungsanleitung

SAFETY SECURITY

MAGNET GUARD

MODEL S082X/S082K

S082X

S082K

OPERATION MANUL

3.INSTANT mode.

When an entryis detected. Thealarm sounds

immediately. This is used to protect you when you

are at home.

4.DELAYmode.

This mode isused when youare leaving yourhome.

On your return,an entry alertbeep tone willsound

to alert youto disarm theunit. If theunit is not

disarmed within10 secondsof entry,the alarm will

sound a110db(S082KA is115db) alarmsiren.

5.The 110db/115db alarmwill sound forabout 30/36

seconds, while thealarm is soundingor during the

entry alert timethe security codecan be enteredto

disarm the unit.

6.To disarm the unit, enter the security code followed by

the #ON/OFF button.

CHIME MODE

1.Before activating the chime, slide the function switch

to the CHIME position.

2.Enter the security code followed by the #ON/OFF button.

3.The ARM LED will illuminate to verify the unit is ON,

followed by a short beep. If theARM light does not

illuminate this indicated the unit is OFF.

4.The chime will sound if there is an entry. The chime will

sound for each entry until the unit is turned OFF(disarmed)

NOTE: The position of the function switch does not

necessarily indicate the mode the unit is in

(CHIME / INSTANT / DELAY). Each time before

activating the unit, set the function switch to the correct

position for the mode desired.

PANIC ALARM

The red PANIC button on the front panel activates the

alarm during a possible emergency.

1.Press the panic button. This will activate the 110db

(S082KA is 115db) alarm siren.

2.Disarm the PANIC alarm, follow the same procedure as

you would to DISARM the unit.

CAUTION

THE MAGNET GUARD IS EXTREMELY LOUD. FOR YOUR

SAFETY. NEVER PLACE THE UNIT CLOSE TO YOUR EARS.

TO TEST THE ALARM, DIRECT THE UNIT AWAY FROM YOU

AT ARMS LENGTH AND ACTIVATE.

PATENT PENDING NOTICE

THIS PRODUCT IS PROTECTED UNDER FEDERAL PATENT. TRADEMARK AND COPYRIGHT

LAWS AND LAWS PREVENTING UNFAIR COMPETITION. NO DUPLICATION OR SIMULATION OF

THIS PRODUCT IS PERMITTED EXCEPT BY WRITTEN AUTHORIZATION OF TECHKO, INC.

TECHKO AND THE CONFIGURATION OF THIS PRODUCT ARE TRADEMARKS OF TECHKO, INC.

ALARM OUTPUT AND PANIC BUTTON TEST

Totest the alarmoutput, press the PANIC button located on

front of theunit. (THIS UNITIS VERYLOUD, COVER THE

SIREN ON THEFRONT OFTHE UNIT BEFOREACTIVATING).

The unit willimmediately sound apiercing alarm siren.To

disarm the unit,enter your securitycode followed bythe

#ON/OFF button. (If youhave not entereda security code

the default is 0 and S082K is 5

CHIME TESTING

1.Set the functionswitch to the CHIME position.

2.Enter the securitycode followed bythe #ON/OFF button,

the ALARM LED will illuminate. If this does not happen

repeat steps 1and 2.

3.Close the doorand then openit again, apleasant chime will

sound 3 times.

4.Todisarm the unit,enter the securitycode followed by the

#ON/OFF button.

5.As long asthe unit isin the ARM mode, the chimewill

continue to sounduntil DISARMED .

ALARM TESTING

1.Set the functionswitch to the INSTANT or DELAY

position.

2. Enter thesecurity code followedby the #ON/OFF button,

the ARM LED will turn on. If this does not happen, repeat

steps 1 and2.

3. Close thedoor and openit again in INSTANT mode, the

alarm sounds immediately. If thealarm is in DELAY mode,

the alarm willemit a lowbeep tone toalert your todisarm the

unit, if notdisarmed, the unitwill then sounda piercing alarm.

4.Todisarm the unit,enter the securitycode followed bythe

#ON/OFF button.

Note: in both modes, CHIME or ALARM (instant / delay) the unit will continue to

sound until DISARMED . The unit will only sound the ALARM if ARMED in

the ALARM mode. If armed in the CHIME mode the unit will sound only the CHIME.

If function switch is changed after the unit has been activated, this will not alter the

sound being produced.

ALARM MODE

1.Before arming theunit slide thefunction switch tothe

INSTANT/DELAY position.

2.Toarm the S082X/ S082K, enterthe security code

followed by the #ON/OFF button, the ARM LED will

turn on. Ifthis does nothappen repeat steps1 and 2.

TESTING

OPERATION

123

456

789

*0#

S082KA

1 2 3

4 5

* #

PANIC

S082X

TEMPLATE

SCREW HOLE

MODE S082KA

SCREW HOLE

Customer Service :

1-888-8TECHKO (1-888-883-2456)

Website: www.techkomaid.com

Mfg. By

9767 Research Drive

Irvine, CA 92618-4626

MADE IN CHINA

Congratulations on your purchase of the TECHKO model

S082X/S082KA.The MAGNET GUARD provides detection of

unwanted intruders in your home by detecting entry. This

unit can be mounted on any door or window. Arming and

disarming of the unit is done by entering a security

code on the keypad.

1.Read all installationand operation instructions

carefully before using.

2.Alarm siren isvery loud, neverput the unitclose to

your ear.

3.Avoid rough handling.

4.Do not installalarm where itwill be exposeddirectly to

sunlight or highhumidity.

5.The unit canprovide valuable protectionfor your home

and property ifutilized properly.However, this unit can

not guarantee competeprotection against burglary

or robbery.Therefore, TECHKO cannot be heldliable for

loss or damagewhich could occur.

6.Keep this manualin a convenientlocation for future

reference.

INSTALLATION

BATTERYINSTALLATION

1.Remove screws frombattery compartment locatedon the

bottom of theunit .(Fig.1)

2.Install 3 AAA batteries / 9V battery. (Not included).

NOTE: When the batteriesare installed forthe first timeor

are replaced thesecurity code willautomatically default

back to 0 (S082KA factorycode is 5 ) and theLED indicator

will illuminate. Thisunit will alsobe in theARM mode.After

installing the batteryto disarm theunit press 0 / 5 and

the #ON/OFF button. Ashort Confirming beep will sound

and the LEDlight will goout to verifythe unit hasbeen

disarmed.

ENTERING CODE TO ARM AND DISARM

NOTE: The default for the security code is 0 (S082KA default

is 5 ). When the battery is replaced the unit will reset to the

factory set code 0 / 5 .

1.Press the 0 / 5 button or the code that is currently in

memory.(New battery default is 0 / 5 ). If there is an

existing code use that in place of the 0 / 5 .

2.Press the #ON/OFF button, a confirming beep should be

heard.

3.If the wrong security code is entered there will be two tone

beep , this is different from the single beep confirmation.

4.When the unit is armed the ARM LED will illuminate.

PROGRAMMING

A SECURITY CODE

NOTE: The programmable security code can be a 1 to 12 digit code.

(S082KA is 1 to 7 digits). Shorter codes such as 1 to 4 digits are easy to

remember, long codes can provide greater safety. DO NOT INCLUDE

A 0 IN YOUR CODE (S082X). DO NOT INCLUDE A 5 IN YOUR

CODE (S082KA).

TO PROGRAM ASECURITY CODE AFTER

BATTERY INSTALLATION

1.Press the 0 (S082KA is 5 ) button.

2.Press the */CODE button.

3.Enter the new code (1 to 12 digits), (S082KA is 1 to 7).

4.Press the */CODE button, the unit will beep once to confirm

your new code has been entered.

CHANGING A SECURITY CODE TO A NEW CODE

1.Enter the old security code number.

2.Press the* /CODE button.

3.Enter the new code(1 to 12 digits), (S082KA is 1 to 7).

4.Press the */CODE button, the unit will beepo nce to

confirm your new code has been entered.

SELECT A MOUNTING LOCATION

NOTE: Before mounting the unit be sure to read theS AFETY

TIPSs ection at the beginning of the manual.

1.Apply double sided tape (included) to back of sensor switch

pair. Mount sensor without wire to the door or window.

Mount the sensors with wire to the door or window frame.

(Fig.2) Be sure the magnetic sensors are mounted no further

than a 1/4f rom each other.

2.Using the mounting plate as template, mark the screw hole

locations and drill two 1/4h oles. Tap the provided screw

anchor into place. (Fig.3)

3.Secure the mounting plate to the wall with the screws

provided.

4.Snap the alarm unit into place on the mounting plate.

TEMPLATE

SCREW HOLE

MODE S082X

MOUNTING

FEATURES

* Requires nowiring or specialinstallation.

* Built-in 110db (S082KAis 115db)alarm siren.

* Up to12 (S082KA7 digits) digitsprogrammable

security codes.

* Alarm/ chime switchablemode.

* 5-10 secondsentry alarm delaywith alert beeptone.

* Magnetic sensordetects entry.

* Direct access PANIC button.

* 4.5V (31.5V AAAsize) alkaline batteryoperation

(S082KA uses9V battery) (Notincluded).

* OptionalAC adaptor poweroperation for S082KA.

* 2 warningstickers for possiblepoints of entry.

INTRODUCTION

SAFETY TIPS

SENSORS

ON WINDOW

SENSORS

ON DOOR

112233

445566

778899

**00##

S082XS082X

112233

445566

778899

**00##

S082XS082X

112233

445566

778899

**00##

S082XS082X

Fig.2

S082KA

1 2 3

4 5

* #

PANIC

S082KA

1 2 3

4 5

* #

PANIC

S082KA

1 2 3

4 5

* #

PANIC

AFFIX SELF

ADHESIVE

TAPE HERE

KEY HOLE

FOR WALL

MOUNTING

Fig.3

AFFIX SELF

ADHESIVE

TAPE HERE

3x1.5V AAA 1x9V 6F22

Dieses Handbuch passt für folgende Modelle

Andere Techko Sicherheitssystem Handbücher

Techko

Techko Safe Pool S189A Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

CADDX

CADDX NX-6 Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

Blaupunkt

Blaupunkt SA 2700 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Highway Safety Group

Highway Safety Group EA401 Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung