Technaxx TX-171 Bedienungsanleitung
1
Technaxx®* User Manual
WiFi Rear Camera System TX-171
Suitable for most of cars (& vans, SUVs, minibuses, caravans, etc.)
as assistance for reverse parking.
This system should be an aid and should NOT replace the need to drive
carefully.
Do not point the high pressure cleaner directly to the plate holder
camera, or drive through a car wash - the device can be damaged.
NOTE: The Smartphone in the car may only be used if it is firmly fixed in
a holder.
Under no circumstances will the manufacturer or supplier accept any
responsibility or can held liable for any direct or indirect, incidental or
consequential damage, or for injuries resulting from installing or use of
this system.
The manufacturer Technaxx Deutschland GmbH & Co.KG hereby declares
that this device, to which this user manual belongs, complies with the
essential requirements of the standards referred to the Directive RED
2014/53/EU. The Declaration of Conformity you find here:
www.technaxx.de/ (in bar at the bottom “Konformitätserklärung”). Before
using the device the first time, read the user manual carefully.
Service phone No. for technical support: 01805 012643 (14 cent/minute from
German fixed-line and 42 cent/minute from mobile networks). Free Email:
support@technaxx.de
The support hotline is available Mon-Fri from 9 am to 1 pm & 2 pm to 5 pm
Keep this user manual for future reference or product sharing carefully. Do
the same with the original accessories for this product. In case of warranty,
please contact the dealer or the store where you bought this product.
Warranty 2 years
Enjoy your product. Share your experience and opinion on one of the
well-known internet portals.
2
Contents
Features........................................................................................................ 2
Technical specifications................................................................................. 3
Safety regulations.......................................................................................... 4
Product overview........................................................................................... 4
License plate holder with camera............................................................... 4
Commissioning.............................................................................................. 4
Insert the license plate in the holder .............................................................. 7
Camera angle adjustment.............................................................................. 7
Download & install the APP........................................................................... 8
iOS: Setting up the WiFi connection:.......................................................... 8
Android: Setting up the WiFi connection:.................................................... 9
Start/Open the APP JoyTrip..................................................................... 10
Tips, Note & Attention.............................................................................. 11
FAQ............................................................................................................. 11
General information..................................................................................... 12
Environmental conditions............................................................................. 12
Disposal....................................................................................................... 13
Features
⚫Inconspicuous reversing camera in license plate holder
⚫Suitable for most vehicles as assistance for reverse parking
⚫Your Smartphone needs to support IEEE 802.11ac 5GHz
⚫Video stream over WiFi 5GHZ to Smartphone APP (JoyTrip)
⚫Wireless video transmission up to ~15m
⚫IR LED for clear night vision ~3m
⚫Adjustable camera alignements & 120° viewing angle
⚫Power supply of the camera by connection to the reverse light
⚫IP67 camera protection class (dustproof & protection against
temporary immersion)
⚫License plate holder suitable for single-line registration
(52x11cm)
⚫Distance displayed by reversing line on the Smartphone
⚫Take photos and videos via App
⚫More safety in reverse driving
3
Technical specifications
License plate holder with camera and WiFi module
Image sensor
2MP CMOS
Camera resolution / fps
1024x720 pixel / 30
Video compression
H.264
Viewing angle
120°
Min. illumination
0.1Lux / automatic white balance
IR night vision distance
~3m
Power supply
DC12V
Max. current
<270mA
Power wire length
Ca. 4m
Protocol
IEEE802.11ac
Transmission frequency
5GHz
Transmission distance
~15m open space (no interferences)
Max. radiated output power
80mW
Protection class
IP67
Operating temperature
–20°Cup to +50°C
App name / version
JoyTrip / iOS version 12.0 and higher and
Android version 9.0 and higher
App Language
DE, EN, FR, SP
Weight / Dimensions
260g / (L) 52.8 x (W) 3.7 x (H)
12.6cm
Packing
Contents
WiFi Rear Camera System TX-171:
License plate holder with camera, WiFi transmitter
and power connection, Mounting material, User
Manual
4
Safety regulations
The reversing system is an aid and does not relieve the driver of his
duty of care in road traffic according to STVO. Read these
instructions carefully before first use.
Product overview
The rear view camera sends a video signal from the camera via
WiFi (5GHz) to the smartphone. In case another Bluetooth
handsfree device is installed in your vehicle, it may cause
disturbances. Therefore we recommend to deactivate that other
Bluetooth handsfree device while using the reversing system.
License plate holder with camera
1
Connection cable
4
Camera
2
WiFi antenna
5
Mounting holes
3
Infrared-LED
Commissioning
Check the functionality of the components before installation (a
installed product is excluded from the return). Preparing and
installing the license plate holder.
NOTE: You may need a voltmeter to measure the polarity of the
electrical system.
5
CAUTION! If you have no experience in installing electrical
devices on vehicles, you are not allowed to carry out the
following work yourself. Have the assembly and connection
carried out by qualified specialists.
1. Remove your rear license plate including any holder that may be
present. Instead of the built-in holder, mount the license plate
holder with camera here - if possible using the old mounting holes.
First hold it up to the vehicle and prepare for installation:
2. Expose the interior behind the license plate so that you can see
the license plate carrier plate from the inside. In the area of the
license plate and license plate light, look for an existing cable duct
in the rear of the vehicle or in the tailgate. If there is no usable cable
passage here, you will have to drill your own cable passage. Mark a
drilling point that is hidden under the camera module or license
plate.
Note: You may need to drill a 6mm hole for the connection cable.
3. After drilling, seal the sheet metal edge with a suitable rust
preventive agent.
4. Push the connection cable through the hole into the vehicle and
connect the power wire to the connection cable. Carefully seal the
cable entry with a suitable body sealing compound so that no water
can get into the vehicle. Screw the license plate holder into place,
taking care not to damage the cable seal. If necessary, re-seal from
the inside.
5. Try to lay the power wire like it is seen in the below images. Make
sure that the cable routing is clean so that opening and closing
cannot break the cable.
6
Note: The pictures are just advice. Depending on your car it can be
a different way.
License plate holder installed to
the trunk lid.
License plate holder installed to
the bumper.
6. Remove the cover of the reverse light.
7. The thin two-core cable is used for power supply and as a
switching signal when reverse gear is engaged. Connect the two
wires with the two contacts of your reversing light. To do this, you
need to know their polarity (measure or check the circuit diagram):
The red cable must be mounted on the positive pole of the
reversing light and the black cable on an earth contact.
8. Install the tail light cover again.
Important: This installation only shows the rear view when the
reverse gear is chosen. Then the rear view camera gets power and
the WiFi signal is transmitted. The connected Smartphone shows
the rear view via App.
Note: If your 12V connection of the rear view camera has a
permanent plus the signal will be transmitted permanently. This can
drain the car battery!
Because of this we do not recommend a permanent
connection. If you want a permanent connection make sure it
linked with the ignition of the car!
7
Insert the license plate in the holder
The following drawings show in sequence the insertion of the
license plate.
1. Step
→Slide the license plate into the upper
opening.
→→ Press the license plate towards
the holder.
2. Step
→→→ Slide the license plate down
until it stops.
Camera angle adjustment
Set the camera at an angle where you
have a good view to the rear, depending on
the height of the license plate holder from
the ground.
Adjustable angle for flexibility: 75°
The displayed lines on the Smartphone give you an indication of the
distance. Definitely control the distance with a folding ruler.
Then tighten the screws on both sides of the camera
→Explanations for the installation of the Smartphone APP can be
found on the following pages.
8
Download & install the APP
Special Attention:
This product uses 5GHz high-speed WiFi chip. Your Smartphone
must support 5GHz WiFi (IEEE 802.11ac 5GHz). Low-end or old
Smartphones do probably do not support a 5GHz Wifi connection.
To download the App JoyTrip from the Appstore or the Playstore
search for “JoyTrip” or scan the QR-code below.
[iOS 12.0 or above; Android 9.0 or above (09-2021)]
iOS
APP icon
Android
iOS: Setting up the WiFi connection:
→Go to Settings of your Smartphone and
open WiFi.
→Select CAR-WIFI-XXXX as WiFi
connection.
→The connection is made.
→→ Open the APP JoyTrip.
Info: If you want that you have an internet
connection while using the JoyTrip App
you can enable the “Wi-Fi Assist” under
Mobile Data on your iPhone.
9
Android: Setting up the WiFi connection:
→Go to Settings of your Smartphone
and open WiFi.
→In the WiFi list, select CAR-WIFI-
XXXX.
→The connection is made.
→→ Open the App JoyTrip.
Info: If you get the message on your
Smartphone that CAR-WIFI-XXXX has
no internet access:
1. Ignore that prompt message. WiFi and
mobile network can be used at the same
time. Convenient for mobile phones to
use another App with Internet connection
meanwhile.
2. After you click Yes to confirm the use
of this network, the Smartphone will not
communicate with the mobile network as
long as you are connected with the CAR-
WIFI-XXXX. The Smartphone will not be
able to access the Internet via mobile
network for this time. The rear view
camera can be used normally. If you
need to reset this setting, ignore WiFi
and reconnect to it
10
Start/Open the APP JoyTrip
iOS
Android
Take a snapshot of the current live view
Take a video of the current live view.
See the live image from the rear view camera
See taken photos and recorded videos in the gallery
- Mirror the camera image (Video Flip Horizontal)
- Show or hide distance marks (Auxiliary Reversing Line)
- Find a short description how to use the App (User
Manual)
- See the privacy policy (Privacy Policy)
- See the App version (App version)
Inhaltsverzeichnis
Andere Technaxx Dashcam Handbücher
Technaxx
Technaxx TX-21 Bedienungsanleitung
Technaxx
Technaxx TX-185 Bedienungsanleitung
Technaxx
Technaxx 1080P TX–14 Bedienungsanleitung
Technaxx
Technaxx TX-185 Bedienungsanleitung
Technaxx
Technaxx TX-124 Bedienungsanleitung
Technaxx
Technaxx CarHD Cam 1080P TX-14 Bedienungsanleitung
Technaxx
Technaxx SafeGuard TX-13 Bedienungsanleitung
