TechnoAP APV8016A Bedienungsanleitung

Digital Signal Processor

APV8016A

Instruction Manual

Version2.0.5

October2022

TechnoAPCo., Ltd.

Add:2976-15 Mawatari,Hitachinaka-shi, Ibaraki, Postcode: 312-0012

TEL: +81-29-350-8011

FAX:+81-29-352-9013

URL:http://www.techno-ap.com

e-mail: info@techno-ap.com

APV8016A Instruction Manual

TechnoAP Co., Ltd.

Safety Precautions / Disclaimer

Thank you very much for purchasing the APV8016A (hereinafter "This board") of TechnoAP Co.,

Ltd. (hereinafter "We"). Please read this "Safety Precautions / Disclaimer" before using this

device, be sure to observe the contents, and use it correctly.

We are not responsible for any damage caused by abnormality of device, detector, connected

device, application, damage to failure, other secondary damage, even if accident caused by using

this device.

Prohibited matter

⚫This device cannot be used for applications requiring special quality and

reliability related to human life, accident.

⚫This device cannot be used in places with high temperature, high humidity, and

high vibration.

⚫Do not apply a power supply that exceeds the rating.

⚫Do not turn the power on while other metals are in contact with the board

surface.

Note

⚫If there is smoking or abnormal heat generation in this device, turn off the

power immediately.

⚫This board may not work properly in noisy environments.

⚫Be careful with static electricity.

⚫The specifications of this board and the contents of the related documents are

subject to change without notice.

APV8016A Instruction Manual

TechnoAP Co., Ltd.

Warranty policy

The warranty conditions of "our product" are as follows.

Warranty period

One year from date of purchase.

Guarantee contents

Repair or replacement will be carried out in case of breakdown even

though you have used correctly according to this instruction manual

within the warranty period

Out of warranty

We do not warranty if the cause of the failure falls under any of the

following.

1. Failure or damage due to misuse or improper repair or modification or

disassembly.

2. Failure and damage due to falling etc.

3. Breakdown / damage in harsh environments (high temperature / high

humidity, under zero, condensation etc.).

4. Causes other than the above, other than "our products".

5. Consumables.

APV8016A Instruction Manual 
4 
TechnoAP Co., Ltd. 
- Table of Contents - 
 
１． Overview....................................................................................................................................................................................................................6 
１．１． Overview........................................................................................................................................................................................................6 
１．２． Features..........................................................................................................................................................................................................8 
２． Specifications................................................................................................................................................................................................... 10 
３． Appearance.......................................................................................................................................................................................................12 
３．１． On-board setting............................................................................................................................................................................ 14 
４． Application installation and network configuration...........................................................................................17 
４．１． Application Installation.............................................................................................................................................................. 17 
４．２． Connection............................................................................................................................................................................................. 17 
４．３． Network setup...................................................................................................................................................................................18 
５． Applicationwindow........................................................................................................................................................................................... 19 
５．１． Startupwindow........................................................................................................................................................................................19 
５．２． CH tab.........................................................................................................................................................................................................23 
５．３． config tab.................................................................................................................................................................................................37 
５．４． status tab.................................................................................................................................................................................................40 
５．５． wave tab...................................................................................................................................................................................................41 
５．６． option tab * optional................................................................................................................................................................... 42 
５．６．１． list-pileup-wave part * optional........................................................................................................................................ 42 
５．６．２． list-wave part * optional...........................................................................................................................................................45 
５．７． histogram tab...................................................................................................................................................................................... 49 
６． Setup tutorial....................................................................................................................................................................................................51 
６．１． Checkingthepreamplifieroutputsignal............................................................................................................................. 51 
６．２． Power supply and connection....................................................................................................................................... 51 
６．３． Setting excecution.........................................................................................................................................................................51 
６．４． Analog Course Gain and Analog Pole Zero Adjustment of Preamplifier Output Signal
 52 
６．４．１． Resistive feedback preamplifier output signal...............................................................................................52 
６．４．２． For transistor-reset preamplifier output signal...............................................................................................54 
６．５． FAST filter setting.......................................................................................................................................................................... 55 
６．６． SLOW filter setting.........................................................................................................................................................................57 
６．７． SLOW threshold setting.........................................................................................................................................................60 
７． Measurement...................................................................................................................................................................................................61 
７．１． Setting.......................................................................................................................................................................................................... 61 
７．２． Start measurement...................................................................................................................................................................... 61 
７．３． Histogram mode..............................................................................................................................................................................61 
７．４． List mode.................................................................................................................................................................................................. 62 
７．５． List wave mode * optional................................................................................................................................................... 62 
７．６． List pile-up wave mode * optional............................................................................................................................. 62 

APV8016A Instruction Manual 
5 
TechnoAP Co., Ltd. 
７．７． Stop measurement.......................................................................................................................................................................62 
８． Quit...............................................................................................................................................................................................................................62 
９． Various data files and formats...................................................................................................................................................63 
９．１． Histogram data file........................................................................................................................................................................ 63 
９．２． List data file............................................................................................................................................................................................65 
９．３． List waveform data file * optional...............................................................................................................................66 
９．４． List pile-up waveforme data file * optional......................................................................................................68 
１０． Auto analog pole zero....................................................................................................................................................................70 
１０．１． Startup window.........................................................................................................................................................................71 
１０．２． Execution...........................................................................................................................................................................................72 
１０．３． Precautions......................................................................................................................................................................................73 
１０．４． Quit............................................................................................................................................................................................................73 
１１． Gaussian fitting........................................................................................................................................................................................74 
１１．１． Startup window.........................................................................................................................................................................75 
１１．２． Online Gaussian Fit Analysis.......................................................................................................................................77 
１１．３． Offline Gaussian Fit Analysis......................................................................................................................................78 
１１．４． Precautions......................................................................................................................................................................................79 
１１．５． Quit............................................................................................................................................................................................................79 
１２． Peak search.................................................................................................................................................................................................80 
１２．１． Startup window.........................................................................................................................................................................81 
１２．２． Online Peak Search Analysis......................................................................................................................................83 
１２．３． Offline Peak Search Analysis.....................................................................................................................................84 
１２．４． Precautions......................................................................................................................................................................................84 
１２．５． Quit............................................................................................................................................................................................................85 
１３． Troubleshooting............................................................................................................................................................................................ 86 
１３．１． Connectionerroroccurs............................................................................................................................................................86 
１３．２． Command error occurs....................................................................................................................................................86 
１３．３． Histogram is not displayed.............................................................................................................................................87 
１３．４． Change IP addres....................................................................................................................................................................87 
１４． APV8016A performance graph......................................................................................................................................88 
１４．１． Energy resolution and counting rate................................................................................................................88 
１４．２． Input and output count rates................................................................................................................................... 88 
１４．３． Linearity................................................................................................................................................................................................89 
１５． Example of Measurement..........................................................................................................................................................90 
１５．１． Energy spectrum when using transistor reset type Ge semiconductor detector
 90 
１５．２． Example of multi-element Ge detector measurement................................................................90 
１５．３． Example of Silicon Drift Detector (SDD) measurement............................................................. 91 
 

APV8016A Instruction Manual

TechnoAP Co., Ltd.

１． Overview

１．１． Overview

TechnoAP'sDSP(DigitalSignalProcessor)productsaremulti-channelanalyzers(MCA)withreal-time

digital signalprocessing capability.

Inconventionalradiationmeasurement,signalsfromapreamplifierarepassedtoaspectroscopyamplifier,

amplifiedandwaveform shapedbyanalogcircuits,andthenanalyzedforspectraaccordingtoa

measurementdevicesuchasan MCA.

InthecaseofDSP,thesignalfromthepreamplifierisdirectlyconvertedtodigitalusinganextremelyfast100

MHz,14BitA/Dconverter.ThedigitallyconverteddataissenttoahighlyintegratedFPGA(Field

ProgrammableGateArray)forspectralanalysisusingnumericaloperations.Thepreamplifiersignalis

trapezoidallyfiltered(TrapezoidalFilter)in real-timeby thepipelinedarchitecture of theFPGA.

TheDSPconfigurationintegratesaspectroscopicpeeramplifierandanMCAtoperformpulseshaping

usingthelatestdigitalsignalprocessingtechniquesinsteadoftraditionalanalogmethods.

Inadditiontothetrapezoidalfilter,theDSP hasatimingfilteramplifier,CFD,andwaveform digitizer.

Itprovidesexcellentenergyandtimeresolutionandisextremelystableevenathighcountingrates.Italso

offersthroughput(>100Kcps)higherthangateintegratoramplifiers,whichboastthehighestthroughputof

anyanalogsystem.

Multi-channelDSPswithupto16 channelsareavailablewithallADCsoperatingsynchronouslyandcan

alsobesynchronizedbetweenmodules.Itcanbeappliedtomulti-channelsystems,coincidenceandanti-

coincidencesystems, andenergyandtimecorrelationanalysis.

Thismanual describesthis equipment.

* Theboardofthisdevicemayberevised,andtheremaybeadditionalchangesinfunctionssuchasthe

presenceorabsenceofjumpersontheboardandthepresenceorabsenceofGNDterminals.Therevision

number(e.g.,APV8016A5)maybeindicatedontheboardsilk.

*Inthetext,"CH"iscase-sensitiveforsignalinputchannelsand"ch"forbinnumberchannels.List"and

"event" aresynonymous.

* The APV in the model’s nameindicatestheVMEstandardsizeboardtype.AseparateVMEpowersupply

rack(suchasourAPV9007)isrequiredtosupplypowertothisboardtype.Inaddition,thetypeofmodelin

whichthisboardishousedinaunit(chassis)andACpowersupplycanbeuseddirectlyismarkedwithAPU

insteadofAPV.Forexample,themodelinwhichtheVME-typeAPV8016Aisinstalledinaunitiscalled

APU8016A.Thismanual alsoincludesadescriptionoftheAPU8016A.

APV8016A Instruction Manual

TechnoAP Co., Ltd.

*The8CH versionisAPV8008A,andthefunctionsaredescribedasthesameexceptforthenumberof

CHs.

*Thefunctionscanbeaddedtothisdeviceasanoption.Inthisdocument,thefunctionpartisspecifiedas

(optional).

APV8016A Instruction Manual

TechnoAP Co., Ltd.

１．２． Features

The main features are as follows.

・Digital signal processing for gamma-ray/X-ray spectroscopy

・Suitable for multi-channel, multi-functional systems such as HPGe semiconductor detectors,

multi-element semiconductor detectors, and anticompton spectrometers

・Spectral analysis of scintillation (NaI(Tl), LaBr3(Ce)) detectors

・Digital Pulse Shaping using highly integrated FPGA

・Data recording via Ethernet (TCP/IP)

Figure1 DSPconfigurations

The output signal from the detector's preamplifier is directly input to the board and digitized by a

high-speed ADC (100MSPS) in the DSP. The A/D converter, which is the heart of the digital pulse

processing, uses the latest 100 MHz, 16 Bit high-speed, high-resolution pipeline type ADC to

directly digitize the signal from the preamplifier.

Trapezoidal waveform processing is performed by hardware operation in FPGA. The shaping time

required for trapezoidal waveform shaping is set by parameters from a PC, and both FAST and

SLOW systems digitally detect peak values using peaking time (peakingtime = rise time + flat top

time).

The FAST and SLOW systems are processed by two different filter blocks.

The FAST system acquires timing and performs pile-up rejection (Pile up Reject).

The SLOW system performs Pole zero Cancel and Baseline Restorer processing followed by

energy analysis.

Preamplifier signals and trapezoidal waveform processing signals imported into FPGA are output

via DAC (Digital Analog Converter), and operation can be checked on a digital oscilloscope.

Settings and data acquisition for the DSP are performed by the supplied DSP application

(hereinafter referred to as "this application"). This application runs on Windows. The DSP

TFA FAST

CFD

Trapezoidal

filter BLR PEAK

HOLD

DET Preamp

1Gbps

Ethernet

DAC

AMP ADC

FPGA

Digital

Signal

Processor

Ethernet

Board LAN

Oscillo

scope

FAST

DISC PUR

ICR

Time ICR

LLD / ULD Energy

OCR OCR

ADC

DATA

16bit

APV8016A Instruction Manual

TechnoAP Co., Ltd.

communicatesonlyviaTCP/IPor UDP networkcommunication,so nospecial librariesarerequired,

and the DSP can be used in non-Windows environments as well.

APV8016A Instruction Manual

TechnoAP Co., Ltd.

２． Specifications

（１） Analog Input

・Number of channel 16

・Input range ±12 V * ±12 V with input protection circuit

・Input impedence 1 kΩ

・Coarse gain ×1、×2、×5、×10

・Frequency band DC to 25MHz

・First-stage differencial circuit 6.8 μs fix * Can be changed upon request

・Attenuator None or 1/10 * Depends on jumper setting on board

（２） ADC

・Sampling frequency 100 MHz

・Resolution 16 Bit

・Input range ±2 V

・Base line noise 0.104 mV (1.7 LSB Rms)

・Energy Resolution 1.70 [email protected] MeV (typ.)

・Spectral broadenning 12 % or less (1 kcps to 100 kcps)

・Throughput 200 kcps and more

・Integral non-linearity ±0.025 % (typ.)

・Peak shift THD

・Drift characteristics THD

・Pulse pair resolution 1.25 × (Risetime + Flat top Time) * Guideline

（３） MCA

・ADC gain 16384, 8192, 4096, 2048, 1024, 512, 256 channel

・Operation mode Histogram, List and Wave

・Event transfer rate Approx. 20 Mbyte per sec. * 16 Byte (128 Bit) per event

（４） Option

・list-pileup-wave Pileup waveform data is added to the list data when a pileup is

detected.

・list-wave Adds waveform data of selected CH to list data

Inhaltsverzeichnis

Andere TechnoAP Signalprozessor Handbücher

TechnoAP

TechnoAP APV8032 Bedienungsanleitung

Beliebte Signalprozessor Handbücher anderer Marken

2Y-LINK Technology

2Y-LINK Technology CI-12-ASP-DAASS Bedienungsanleitung

Crane Song

Crane Song Falcon Bedienungsanleitung

Steg

Steg DSP 6 Bedienungsanleitung

Rocktron

Rocktron INTELLIFEX LTD Bedienungsanleitung

RF-Lambda

RF-Lambda RF1457 Bedienungsanleitung

TC Electronic

TC Electronic DB8 MKII Handbuch

Acqiris

Acqiris U5309A Bedienungsanleitung

PCI

PCI MicroTrans EQ Handbuch

Crestron

Crestron Avia DSP-1282 Bedienungsanleitung

turck

turck MS96-11EX0-R/24VDC Bedienungsanleitung

Rolls

Rolls ROTORHORN RP147 Bedienungsanleitung

ESX

ESX QUANTUM QL810SP Bedienungsanleitung

Oberheim

Oberheim GM-1000 Bedienungsanleitung

AMC

AMC DSP8X8 Bedienungsanleitung

Planet Audio

Planet Audio PC3.5B Bedienungsanleitung

Behringer

Behringer Super-X Pro CX3400 Bedienungsanleitung

Euphonix

Euphonix DF64 Digital Frame Bedienungsanleitung

Lem Elettronica

Lem Elettronica DSP30-4G Bedienungsanleitung