Technoline 433MHz Remote Thermo Bedienungsanleitung

433 MHZ REMOTE THERMO

INTRODUCTION:

Congratulations on purchasing this innovative 433MHz Remote Thermo which displays indoor

and up to three outdoor temperature readings. To enjoy the full benefits of this innovative product,

please read this operating manual.

REMOTE THERMO:

Detachable stand

CH key

MIN/MAX key

Hanging hole

TEMPERATURE TRANSMITTER:

Holder

FEATURES:

• Temperature display in degrees Celsius

• Indoor temperature display

• Outdoor temperature display

• MIN/MAX indoor and outdoor temperature display

• Can receive up to three outdoor transmitters

• Table standing or wall mountable (detachable table stand)

SETTING UP:

Please follow these steps to ensure that your new Remote Thermo works correctly with the

temperature transmitter(s):

Battery

compartment

Battery compartment

Battery cover

1. Flip open the battery cover at the back of the Remote Thermo as indicated above.

2. Checking the correct polarization, insert 2 x AAA, IEC LR3, 1.5V batteries into the battery

compartment and replace the cover (all the segments of the LCD screen will light up

momentarily).

3. Now slide the battery cover open on the transmitter as indicated above

4. Checking the correct polarization, insert 2 x AAA, IEC LR3, 1.5V batteries into the battery

compartment and replace the cover.

5. If you have purchased additional outdoor transmitter(s) wait until the outdoor temperature

has been received from the one transmitter before activating the next transmitter by

repeating steps 3 and 4.

6. However, ensure that you leave 10 seconds in between the reception of the last

transmitter and the set-up of the following transmitter. The Remote Thermo will number the

transmitters in the order of set-up, i.e. the first transmitter will have the temperature

displayed with the number 1 against it and so on.

7. When the outdoor temperature(s) is received the Remote Thermo and transmitter(s)

should be positioned in the desired places (see Positioning & securing below)

Note:

Should the total time of inserting the batteries into the transmitters take longer than 2-1/2 minutes

from the time of inserting the batteries into the Remote Thermo then temperature reception

problems may occur. If the temperature is not received, then see Checking for 433 MHz

reception, before resetting the units (see Resetting the Remote Thermo below).

In the event of changing batteries in any of the units, all units need to be reset by following the

setting up procedures. This is because a random security code is assigned by the transmitter at

start-up and this code must be received and stored by the Remote Thermo in the first 2-1/2

minutes of power being supplied to it.

In the event of changing batteries in any of the units, all units need to be reset by following the

setting up procedures. This is because a random security code is assigned by the transmitter at

start-up and this code must be received and stored by the Remote Thermo in the first 2-1/2

minutes of power being supplied to it.

LCD SCREENLCD SCREEN

The Remote Thermo’s LCD is comprised of three lines and once the batteries are inserted, all the

segments will light up momentarily before displaying:

The Remote Thermo’s LCD is comprised of three lines and once the batteries are inserted, all the

segments will light up momentarily before displaying:

1. Indoor temperature in degree Celsius (°C)1. Indoor temperature in degree Celsius (°C)

2. Outdoor temperature in degree Celsius (°C)2. Outdoor temperature in degree Celsius (°C)

Outdoor transmission

signal

Indoor Temperature

in ºC

Transmitter identification number

Outdoor Temperature in ºC

USING THE REMOTE THERMO:

INDOOR TEMPERATURE:

The indoor temperature is displayed on the first line of the LCD. The Remote Thermo’s built in

sensor automatically measures the temperature once the batteries are inserted.

OUTDOOR TEMPERATURE READING:

The outdoor temperature is displayed on the bottom line of the LCD. The Remote Thermo

receives the outdoor temperature via 433MHz frequency when the batteries are inserted into the

transmitter within the 2-1/2 minutes of the setting up time (See Setting up above).

Note: Should the outdoor temperature not be received within 2-1/2 minutes after inserting the

batteries into a transmitter, then see “Checking 433 MHz reception” below.

MINIMUM AND MAXIMUM INDOOR AND OUTDDOR TEMPERATURE

RECORDINGS:

To view the minimum or maximum indoor and/or outdoor temperature, press the “MIN/MAX” key

to view:

1. MIN indoor temperature

2. MAX indoor temperature

3. MIN outdoor temperature

4. MAX outdoor temperature

5. To return to current indoor and outdoor temperature display

Remarque:

Once a new indoor temperature high or low is reached, it will automatically set into the Remote

Thermo’s memory.

MIN indoor

temperature MAX indoor

temperature

MIN outdoor

temperature MAX outdoor

temperature

MIN icon MAX icon

RESETTING THE MINIMUM AND MAXIMUM TEMPERATURE RECORDING:

TO RESET THE MIN OR/AND MAX INDOOR TEMPERATURE RECORDS:

1. Press the “MIN/MAX” key to select the indoor MIN or MAX records.

2. Press and hold the “CH” key for 3 seconds. Both the MIN and MAX records will be

reset to current indoor temperature.

TO RESET THE MIN OR/AND MAX OUTDOOR TEMPERATURE RECORDS:

1. First selected the transmitter to reset by pressing the “CH” key if more than one

transmitter is used. There is no transmitter number displayed if only one transmitter

is used.

2. Press the “MIN/MAX” key to select the outdoor MIN or MAX records.

3. Press and hold the “CH” key for 3 seconds. Both the MIN and MAX records will be

reset to current outdoor temperature.

Note: If more than one transmitter is used, repeat the same steps above for each transmitter.

OUTDOOR TEMPERATURE 1, 2, AND 3

If the more than one transmitter is being used, to alternate between the temperature readings of

transmitter 1, 2, and 3, simply press the “CH” key. If the reading is from transmitter 1, then the

identification numbers 1 will be displayed in the outdoor temperature section of the LCD. The

same will apply to the next transmitter and so on. However, if only one transmitter is used, no

identification number will be displayed on the LCD.

CHECKING FOR 433 MHz RECEPTION:

In normal surroundings (for example away from interfering sources such as TV sets), the outdoor

temperature can usually be easily received within 2-1/2 minutes. If the outdoor temperature is not

displayed on the LCD after 2-1/2 minutes, then check the following:

1. The distance of the units should be at least 1.5 - 2.0 meters away from interfering sources

such as computer monitors or TV sets.

2. Avoid placing the units onto or in the immediate proximity of metal doors, window

frames or structures.

3. Using other electrical products such as headphones and speakers that operate on the

same signal (433 MHz) can prevent the transmission pick up.

4. Neighbours using electrical products operating on the 433MHz signal can also cause

interference. In most severe cases, the reception is only possible once all other electrical

products using the 433MHz are switched off.

5. Within thick concrete rooms such as basements and tower blocks, the 433MHz signal can

be weakened (avoid placing near metal frames and structures).

6. Transmission can be affected by exposure to extreme temperature conditions. For

example, if the weather has been extremely cold (under -25ºC) for an extended period of

time then the transmission signal may be weakened. (Please bears this in mind when

positioning the transmitter).

Note: Should after checking the above list and the outdoor temperature is still not received,

then reset the units (see Resetting the Remote Thermo below).

RESETTING THE REMOTE THERMO:

1. Remove the batteries from the Remote Thermo and the transmitter(s)

2. Wait at least 30 seconds and repeat the procedures specified in Setting up above.

Inhaltsverzeichnis

Andere Technoline Thermometer Handbücher

Technoline

Technoline WA3060 Bedienungsanleitung

Technoline

Technoline WS 9119 Bedienungsanleitung

Technoline

Technoline WS 9119 Bedienungsanleitung

Technoline

Technoline WS 9114 Bedienungsanleitung

Technoline

Technoline WS 1050 Bedienungsanleitung

Technoline

Technoline WS-1009 Bedienungsanleitung

Technoline

Technoline IR 380 Bedienungsanleitung

Technoline

Technoline WS 7026 Bedienungsanleitung

Technoline

Technoline WS 7002 Bedienungsanleitung

Technoline

Technoline WS 7024 Bedienungsanleitung

Technoline

Technoline IR 200 Bedienungsanleitung

Technoline

Technoline WS 8006 Bedienungsanleitung

Technoline

Technoline WS 7025 Bedienungsanleitung

Technoline

Technoline WS 1004 Bedienungsanleitung

Technoline

Technoline WS 7005 Bedienungsanleitung

Technoline

Technoline WS 9175 Bedienungsanleitung

Technoline

Technoline WS 7025 Bedienungsanleitung

Technoline

Technoline WS 1080 Bedienungsanleitung

Technoline

Technoline WS 9420 Bedienungsanleitung

Technoline

Technoline WS 7006 Bedienungsanleitung

Technoline

Technoline WS 7012 Bedienungsanleitung

Technoline

Technoline WS 7003 Bedienungsanleitung

Technoline

Technoline WS 9118 Bedienungsanleitung

Technoline

Technoline WS9440 Bedienungsanleitung

Beliebte Thermometer Handbücher anderer Marken

Delton

Delton 981A Bedienungsanleitung

Baker

Baker MM2P Bedienungsanleitung

Tarmo

Tarmo 320281 Bedienungsanleitung

Citizen

Citizen CTD 504 Bedienungsanleitung

TFA

TFA 14.1500 Bedienungsanleitung

Vive

Vive DMD1010 Bedienungsanleitung

Gotemp

Gotemp THB4002 Bedienungsanleitung

GREISINGER

GREISINGER G 1202 Bedienungsanleitung

Amprobe

Amprobe TMD-53W Bedienungsanleitung

Trotec

Trotec BP10 Bedienungsanleitung

Radiance instruments

Radiance instruments RT616 Series Bedienungsanleitung

Eurolec

Eurolec IR151 Bedienungsanleitung

Scaneo

Scaneo TS42B Bedienungsanleitung

Sper scientific

Sper scientific 800043 Bedienungsanleitung

Motorola

Motorola MBP69SN Konfigurationshandbuch

The MeatStick

The MeatStick The MeatStick Bedienungsanleitung

Hama

Hama TH35-A Bedienungsanleitung

Veridian Healthcare

Veridian Healthcare 09-349 Bedienungsanleitung