TECO F510 series Bedienungsanleitung

Page 1 of 11 06/10/17

TECO F510 Inverter

Quick Start Guide

1) Ensure that the Inverter & the motor have the correct KW power and voltage

ratings.

Motor full load amps must not exceed the Inverter rating.

2) Ensure that the supply & Motor cables are connected correctly prior to

power up.

3) Connect supply cable to terminals R/L1, S/L2, T/L3

4) Connect motor cable to terminals U/T1, V/T2, W/T3

(Swap two leads if motor runs in reverse direction).

5) Connect supply Earth and the motor Earth to the drive Earth

terminal.

Note:-

I ) For detailed installation

and wiring refer to the

Instruction

manual.

This guide is to assist you in installing and running the inverter and verify that it is

functioning correctly for it’s main and basic features.

For detailed information and if there are any doubts please refer to the instruction manual.

Step 1

Supply & Motor connection

Page 2 of 11 06/10/17

Apply power to the drive, the display will briefly show the supply voltage

440V followed by flashing.

This is the default (factory set) frequency.

If the unit has been used previously then it will show the last frequency

programmed.

Step 2

Apply power to the drive

005.00

Step 3

Test run from keypad

Press RUN KEY to run.

The frequency will ramp up to 5.0 Hz or the user pre-set frequency

according to the default acceleration ramp time.

Press STOP key to stop.

The frequency will ramp down to zero according to the default decel ramp

time.

Step 4

To alter frequency from keypad. (Default setting).

Use the Arrow keys and

RESET key

to alter the digits to the

required frequency.

To store the set frequency use READ/ENTER Key.

eg. 50.0 HZ then use RUN and STOP keys to start/ stop.

Page 3 of 11 06/10/17

Remote speed reference and Remote run

1) Ensure that you have carried out installation & wiring requirements as

per step1 quick start guide on previous page before you proceed.

Two analogue inputs are available. AI1 & AI2

Ensure 00-07 = 0 ( Default= Main frequency source).

2) Select AI1 or AI2 as required.

AI1

Voltage only Input. Speed command

0 to +10V

AI2

Multi-function analog input terminal.

Use SW2 to switch voltage or current input

0 to +10V

4 to 20 mA

Settings for AI1:

Set 00-05=1

Settings for AI2 :

Set 00-05 = 7 ( AI2 Aux frequency)

Set 04-05 = 0 ( Default) . Aux frequency.

Set 04-00 = 0 for ( 0-10v or 0-20mA)

Set 04-00 = 1 for ( 2-10v or 4-20mA)

3) Connecting Remote Potentiometer:

Terminal +10V Supply for use with the potentiometer.

Terminal GND 0Vdc

Terminal AI1 or AI2 Potentiometer wiper connection.

4) Connecting Remote 0-10V or 4-20mAc signal

Use terminals AI1 or AI2 as required.

Connect the 0 V of the analogue input signal to Terminal GND .

Step 1

Remote mode wiring. Speed reference.

Page 4 of 11 06/10/17

How to alter parameters

Step 2

Remote mode Run

1) Remote Run signal can be either a PNP or NPN input type.

Set PNP or NPN selection as required by SW3.

Note : PNP (positive voltage switching) selection is recommended

for use in EU.

2) Connect remote start switch if required according to diagram in the

instruction manual.

Terminal 24V & S1 (Forward run)

Terminal 24V & S2 (Reverse run)

24V is the common terminal for PNP type inputs.

24VG (0Vdc) terminal is common for the NPN type inputs.

Step 3

Check/ verify and alter parameters

Check / verify and alter parameters for remote start & remote frequency as

necessary before you proceed. Parameters 00-02 & 00-05

See quick start parameter list & How to alter parameters.

Step 4

RUN using remote speed reference.

(Potentiometer, 0-10Vdc or 4-20mA)

1) To run. Activate the remote run switch connected to terminals

S1 (FWD) or S2 (REV) as required. Parameter 00-02 =1

The frequency will ramp up to the frequency set from keypad or

analogue inputs 1 & 2.and according to the set acceleration ramp

time.

2) To Stop. De-activate the remote run switch.

The frequency will ramp down to zero and according to decel ramp

time.

Page 5 of 11 06/10/17

How to alter Parameters from keypad

1) To alter parameters:- Press the DSP/FUN key,

until the first parameter 00-00 is displayed.

2) Then use the arrow keys </RESET to select the parameter

required then press READ/ENTER key to read the preset value.

3) Use and </RESET keys to alter the setting of the parameters

as per basic quick start parameter list.

Note:- For full parameter list refer to the instruction manual.

4) To save each parameter change, press READ/ENTER

key then the word

END will be displayed.

5) Use </RESET key to select the next parameter to alter and

follow steps 2 to 4 until all changes are complete.

6) Pressing the DSP/FUN key repeatedly will alternate the display between

the preset frequency (flashing display) and the last parameter accessed

or other selectable displays 0 to 7 when selected by parameter 12-00

according to the table below.

【0】:Disable Display 【1】:Output Current

【2】:Output Voltage 【3】:DC Bus Voltage

【4】:Temperature 【5】:PID Feedback

【6】:AI1 Value 【7】:AI2 Value

Page 6 of 11 06/10/17

Type

Name

Functions

Display

Main digital

displays

Frequency, parameter, voltage, current, temperature and

Fault message.

LED status display

FAULT: When the inverter has a warning or fault message,

the indicator lights up.

FWD: When the inverter is in forward run mode, the indicator

lights up.

RUN mode: Continuously ON.

Stop mode: Flashes ON/OFF.

REV: When the inverter is in revere Run mode, the indicator

lights up.

RUN mode: Continuously ON.

Stop mode: Flashes ON/OFF

SEQ: When Run command source is set to external control,

the indicator lights up.

REF: When Frequency command source is set to external

control, the indicator lights up.

Keys

RUN

RUN: Run command at the set frequency.

STOP

STOP: Stop command. Decelerate or Coast to stop.

Page 7 of 11 06/10/17

（8 keys）

▲

Increments parameter number and preset values.

▼

Decrements parameter number and preset values.

LOC/REM

Alternates frequency and run command source between

LOCAL and REMOTE:

REMOTE mode: inverter is controlled per parameter settings

through control circuit terminals or communication.

LOCAL mode: Inverter is controlled through digital operator.

By default REMOTE mode is effective at power on. Press

LOC/REM key to switch between the modes while inverter is

stopped. LOC/REM key can be disabled by parameter 23-41.

DSP/FUN

Select between Frequency, Function (parameters) and

Monitor displays according to the following sequence.

Frequency screen Function selectionMonitor

parametersFrequency screen.

</RESET

“<” is left shift key. It’s used for changing parameter or value.

RESET key：Use to reset Inverter resettable faults.

READ/ENTER

Used to display the preset value of parameters and for saving

the changed parameter values.

Basic Quick Start Parameter List

Parameter

Default

Range

Note

00-00

0, 2, 5

Control Mode:-

0: V/F

2: SLV (Sensorless Vector)

5: PM SLV (Sensorless Vector for

Permanent Magnet Motor)

00-02

0-4

Run mode:-

0: Keypad

1: External control terminal

2: Communication

3: PLC

4: RTC

00-05

0-7

Frequency source:-

0: Keypad

1: Remote control (Analogue Input AI1)

2: External up/down frequency control

3: Communication

4: Reserved

5: PID output

6: RTC

7: Auxiliary Frequency (AI2)

00-01

0-1

Run direction:-

0: Forward

1: Reverse

00-12

100.0%

0.1-109%

Max frequency limit. (default 100%)

00-13

0.0 %

0.0-109%

Min frequency limit. (default 0.0%)

Page 8 of 11 06/10/17

07-09

0-3

Stop method:

0: Deceleration to stop

1: Coast to stop

2: DC injection braking

3: Run signal inhibit (timer) during Coast to

stop

02-01

**A

10%~200% of

rated current (V/f)

25%~200% of rated

current (SLV)

Motor rated current (for Motor overload

protection)

13-08

0-10

Factory Reset: Inverter Supply voltage.

2: 2 wire initialization(220/440V,60Hz)

3: 3 wire initialization(220/440V,60Hz)

4: 2 wire initialization(230/415V,50Hz)

5: 3 wire initialization(230/415V,50Hz)

6: 2 wire initialization(200/380V,50Hz)

7: 2 wire initialization(200/380V,50Hz)

8: PLC initialization

9: 2 wire initialization(230/460V,60Hz)

10: 3 wire initialization(230/460V,60Hz)

Note:- For Full Parameter List see the Instruction manual

Control Modes & Auto Tune

F510 provides three control modes.

Select the relevant control mode for the application.

Default control mode is V/f.

V/f can be used for most applications specifically multi-motor

or applications where auto tune is not successful

or when a customized v/f pattern may be required.

Several V/f patterns are available selectable by parameter 01-00.

Select the appropriate one based on the application load type and the motor base frequency of

50 or 60 Hz.

For selections of the V/f patterns, Refer to the instruction manual.

Sensorless Vector mode SLV is used for obtaining best performance from a motor.

V/f Mode Parameters

Parameter

Default

Range

Note

01-00

0-FF

F: General Purpose. 60Hz system

0: General Purpose. 50Hz system

For full list of preset patterns set by 01-00,

refer to the manual.

FF: Customized V/f.

Set parameters 01-02 to 01-13

Page 9 of 11 06/10/17

For Motor parameters in V/f mode, set the name plate data in parameter Group 2.

SLV Mode set parameters in parameter Group 17

Motor parameters are automatically set when performing an auto-tune (17-10 = 1).

In most case no adjustment is required after performing an auto-tune except when using the

inverter in special applications (e.g. machine tool, positioning, etc…).

Enable auto tune function by parameter 17-10.

Press RUN button (after display showing “Atrdy”)

Six auto tune modes are available. Rotational, Static, Stator Resistance, and loop turning.

Use Rotational where possible. Motor rotates the process takes about 50 secs

Use Static when rotation of load is not possible. It takes about 35 secs.

Use Line to Line Resistance for long cable (above 50 meters in V/f mode)

Use Loop turning to enhance vector control performance.

Rotational Auto-tuning .Combination (Item: 4+2+0). V 1.41

Static Auto-tuning. Combination (Item: 4+2+1). V 1.41

Group 17 Automatic Tuning Function Group

Code

Parameter Name

Range

Default

Unit

17-00

Mode selection of automatic

tuning

0: rotational autotune

1: static autotune

2: stator resistance measurement

3: Reserved

4: loop turning

5: Rotational Auto-tuning

Combination (Item: 4+2+0). V 1.41

6: Static Auto-tuning

Combination (Item: 4+2+1). V 1.41 .

17-01

Motor rated output power

0.00~600.00

17-02

Motor rated current

0.1~999.9

17-03

Motor rated voltage

200V: 0.0~255.0

220

400V:0.0~510.0

440

17-04

Motor rated frequency

10.0~400.0

60.0

17-05

Motor rated speed

0~24000

rpm

17-06

Pole number of motor

2-16 (even number)

Pole

17-08

Motor no-load voltage

200V: 50~240

400V:100~480

17-09

Motor excitation current

0.01~600.00

17-10

Automatic tuning start

0: Disabled

1: Enabled

17-11

Auto tune Error History

0: No error

1: Motor data error

2: Stator resistance tuning error

3: Leakage induction tuning error

4: Rotor resistance tuning error

5: Mutual induction tuning error

6: Reserved

7: DT Error

Page 10 of 11 06/10/17

Group 17 Automatic Tuning Function Group

Code

Parameter Name

Range

Default

Unit

8: Motor acceleration error

9: Warning

17-14

Rotational Tuning Mode

Selection. V 1.41

0: VF Mode

1: Vector Mode

Note:-

No-load motor voltage 17-08 & (02-19)

Parameter determines the rated flux during motor’s rated rotation in SLV control mode. Set

the value of this parameter to the same value as parameter 17-08.

A value of 10~50V below the rated input voltage level (parameter 17-03) ensures that the

motor is capable of providing adequate torque performance when operating at nominal speed

(or higher speed).

Setting the value too small can result in a reduction in no-load current, weakened motor flux

and an increase in motor current while the motor is loaded, causing a reduction in torque

performance.

For high KW rating (55KW and above), set this closer to the supply voltage.

Motor excitation current 17-09 & (02-09)

This parameter is automatically set during auto-tune. No adjustment required.

For static tuning & Resistance tuning this parameter needs to be adjusted

Set to 1/3 of the motor rated current parameter (17-02).

Wiring Diagram

Andere Handbücher für F510 series

Inhaltsverzeichnis

Andere TECO Wechselrichter Handbücher

TECO

TECO L510S Series Installationsanleitung

TECO

TECO L510 Bedienungsanleitung

TECO

TECO L510S Series Bedienungsanleitung

TECO

TECO PA7300 Bedienungsanleitung

TECO

TECO A510 Installations- und Betriebsanleitung

TECO

TECO JN5-CM-USB Bedienungsanleitung

TECO

TECO A510s Bedienungsanleitung

TECO

TECO E710 Series Bedienungsanleitung

TECO

TECO SPEECON 7200GS Bedienungsanleitung

TECO

TECO e510 series Bedienungsanleitung

TECO

TECO A510-2001-H Bedienungsanleitung

TECO

TECO N3 Series Bedienungsanleitung

TECO

TECO speecon 7200ma Bedienungsanleitung

TECO

TECO E510s Series Bedienerhandbuch

TECO

TECO A510s Bedienungsanleitung

TECO

TECO L510 Bedienungsanleitung

TECO

TECO e510 series Bedienungsanleitung

TECO

TECO T-verter N2 Series Bedienungsanleitung

TECO

TECO F510 series Gebrauchsanweisung

TECO

TECO FM50 Series Leitfaden

TECO

TECO F510 series Bedienungsanleitung

TECO

TECO MV510 Series Bedienungsanleitung

TECO

TECO L510S Series Bedienungsanleitung

TECO

TECO F510 series Bedienungsanleitung

Beliebte Wechselrichter Handbücher anderer Marken

Fourgroup

Fourgroup Easy Bedienungsanleitung

Velleman

Velleman PI300M Bedienungsanleitung

Sungrow

Sungrow SG350HX-US Bedienungsanleitung

WilTec

WilTec 61897 Bedienungsanleitung

SMA

SMA SUNNY BOY STORAGE 2.5 Bedienungsanleitung

Simplicity

Simplicity LANDLORD 316 Bedienungsanleitung

Santak

Santak SMAX 3000 Bedienungsanleitung

ATON

ATON RA.Store-3 Bedienungsanleitung

ZIEHL-ABEGG

ZIEHL-ABEGG FXET4AMQ Bedienungsanleitung

Tektronix

Tektronix CFG250 Bedienungsanleitung

Champion

Champion 200989 Bedienungsanleitung

Vanner

Vanner 20-500 Series Bedienungsanleitung

GE GEP Bedienungsanleitung

Astrel Group

Astrel Group Power Reducer Kurzanleitung

MULTIQUIP

MULTIQUIP GDP-5H Leitfaden

GoWISE

GoWISE PS1007 Bedienungsanleitung

Promate

Promate PM13500D ES Bedienungsanleitung

Mastervolt

Mastervolt WHISPER 3.5M3000 RPM Bedienungsanleitung