TECshow FLATSIX Bedienungsanleitung

LED Par Light

USER MANUAL / MANUAL DE USUARIO

PLEASE READ THE INSTRUCTIONS CAREFULLY BEFORE USE

POR FAVOR LEA LAS INSTRUCCIÓNES ANTES DE USAR

FLATSIX

Contents

Section 1.Getting Started

 Unpacking

 Safety Instruction

Section 2. Set Up

 Installation

 Controlling Board

 Machine Connection

Section 3. Troubleshooting

 Troubleshooting

Section 4. Reference

 Control Menu

 DMX Protocol

 Specication

FLATSIX - LED PAR LIGHT

ENGLISH VERSION

p. 2

FLATSIX - LED PAR LIGHT

ENGLISH VERSION

p. 3

Section 1. Getting Started

 Unpacking

 Safety Instruction

Unpacking

 1pc Fixture

 1pc User Manual

 

 1pc Signal Cable

 1pc daisy chain power cable

Thanks for using our FLATSIX range. Carefully unpack the

box and check the contents to ensure that all parts are pres-

ent and in good conditions. If anything looks as if it has been

damaged in transit, notify the shipper immediately and keep

the packing material for inspection. Again, please save the





in the original manufacturer box and packing.

FLATSIX - LED PAR LIGHT

ENGLISH VERSION

p. 4

Safety Instruction

 Please conserve this manual as operation guidance. If

you sell this product to other user, please make sure that

they also receive this user manual.

 Always make sure that you are connecting to the proper

voltage and that the line voltage you are connecting to is

not higher than that stated on the decal or rear panel of



 



       -

sive or corrosive materials surrounded in 0.5 meter

while operating.

 The unit must be installed in a location with adequate

ventilation, at least 50CM away from adjacent surfaces.

Be sure that no ventilation slots are blocked.

 Do not operate at ambient temperatures higher than

104º(40º).

 Safe wire should be used to install machine. Bearing of

safe wire should be 3 times of the machine weight. Com-

-





1m-

tures at most.

 Always disconnect from the power source before servic-

ing or replacing fuse/lamp and be sure to replace with

-

ing, repairing and cleaning the machine.

 



 In case of failure or misfunction occurred, stop using the

unit immediately.

 Repairs carried out by unskilled people can lead to dam-

age or malfunction. Buy the same spare parts/compo-

nents from manufacturer directly.

 

to circuits with a suitable ground. Make sure the power

cord is never crimped or damaged. Do not power on and





 When use DMX controller, please make sure that there

is no interference sources(e.g. intercom, high frequency

radio waves and radiation source)

Caution!

There are no user serviceable parts inside the unit. Do not

open the housing or attempt any repairs yourself. In the un-

likely event your unit may require service, please contact



For your safe, please read this user manual carefully before turn on the xture. This machine should be operated by

qualied engineer.

FLATSIX - LED PAR LIGHT

ENGLISH VERSION

p. 5

Section 2. Set Up

 Installation

 Controlling Board

 Machine Connection

Installation

This machine should be mounted through the screw holes of



and safety wire have strong load capacity to bear 3 times





Controlling Board

Front display panel

MENU switch menu function

UP On function: page up

On numerical value: increase value

DOWN On function: page down

On numerical value: reduce value

ENTER Settle selected function and value

1. Display

Display menu and selected function.

2. Button

3. DMX signal input

Control model by DMX signal: please use 3pin XLR signal cable.

4. DMX Signal output

Transfer DMX signal to next model, please use 3pin XLR

signal cable.

5. Power output

Connect to obtain power (attention: please use connect to

stated voltage.)

6. Power input

Connect to obtain power

FLATSIX - LED PAR LIGHT

ENGLISH VERSION

p. 6

Machine Connection

Cable Connectors

Cables must have a male XLR connector on one end and a

female XLR connector on the other end.

A word on termination: DMX is a resilient communication

protocol, however errors still occasionally occur. Termina-

tion reduces signal errors, and therefore best practices in-

clude use of a terminator in all circumstances. If you are ex-



over long signal cable runs, a terminator may help improve

performance.

To build your own DMX Terminator: Obtain a 120-ohm, 1/4-



They are also readily available from specialty retailers.

 Maximum 8 PCS xtures connected by Daisy chain connection.

Master-Slave control model:





address value or following DMX controller performance(Atten-



FLATSIX - LED PAR LIGHT

ENGLISH VERSION

p. 7

Section 3. Troubleshooting

Probable cause(s) Remedy

No response from xture

when power is applies

 Check power cables

Primary fuse blown Replace fuse

Secondary fuse blown Replace fuse

Fixture resets but does

not respond correctly to

controller

(DMX mode operation)

Controller not connected Connect controller

 

Bad data link connection Inspect cables and correct poor connections and/or

broken cables.

-

tor control Eliminate scene cross-fade on controller

Data link not terminated 

-

mitting on link



regained:unplug both connectors and connect them

directly together

Colors cannot be mixed Random color mixing is on 

Fixture does not reset

correctly Electronic or mechanical failure Contact service technician

No light, lamp cuts out

intermittently,or burns out

too quickly

Lamp missing or blown 

Fixture or lamp is too hot 

technician

Section 4. Reference

 Control Menu

 DMX Protocol

 

Control Menu

DMX Protocol

No. Menu Function (press ENTER button)

1r --- r000-r255: R dimmer, from dark to light

2g--- g000-g255:G dimmer, from dark to light



can mix out all kinds of color

3b--- b000-b255: B dimmer, from dark to light

4A---

A000-A255: Amber dimmer, from darkto light

5U--- u000-u255:uv dimmer, from dark to light

6n--- n000-n255:W dimmer, from dark to light

7F--- , from slow to fast

8C--- C000-C255:color shade speed, from slow to fast

9J--- J000-J255: color skip speed, from slow to fast

10 S--- S000-S255:sound active speed, from slow to fast

11 d--- DMX11 channel mode, should link to DMX controller

12 d--- 

CH Function Description

CH1 Dimmer RGBAUVW linear dimmer from dark to bright

CH2 R Dimmer Red linear dimmer from dark to bright

CH3 G Dimmer Green linear dimmer from dark to bright

CH4 B Dimmer Blue linear dimmer from dark to bright

CH5 A Dimmer Amber linear dimmer from dark to bright

CH6 U Dimmer UV linear dimmer from dark to bright

CH7 W Dimmer White linear dimmer from dark to bright

FLATSIX - LED PAR LIGHT

ENGLISH VERSION

p. 8

CH Function Description

CH1 Dimmer RGBAUVW dimmer, from dark to bright

CH2 R Dimmer Red linear dimmer, from dark to bright

CH3 G Dimmer Green linear dimmer, from dark to bright

CH4 B Dimmer Blue linear dimmer, from dark to bright

CH5 A Dimmer Amber linear dimmer, from dark to bright

CH6 U Dimmer UV linear dimmer, from dark to bright

CH7 W Dimmer White linear dimmer, from dark to bright

CH8 Flash 

CH9 ColorMix Color mixing adjusting

CH10 Stand alone 0-60: shade 61-120: skip 121-180: shade, skip 181-



CH11 Stand alone

Speed

DMX 9 stand alone speed and sound active speed

adjusting, from slow to fast

DMX Protocol (11CH)

Specication:

Voltage: AC100V-240V

Frequency: 50-60Hz

Rated Power: 100W



Control: DMX512

Beam angle: 25° (40° option)



Control Mode: DMX/sound active/auto/ master-slave/manual

Level of Protection: IP20

Stock: Clean and Dry place

Running Temp.: 0°C~40°C

Weight: 2.8kg

Size: 26*26*11.5cm(excluding bracket)

FLATSIX - LED PAR LIGHT

ENGLISH VERSION

p. 9

FLATSIX - PAR LED

VERSIÓN ESPAÑOL

p. 10

Índice

Sección 1. Puesta en funcionamiento

 Desembalaje

 Instrucciones de seguridad

Sección 2. Conguración

 Instalación

 Panel de control

 Conexiones

Sección 3. Resolución de problemas

 Resolución de problemas

Sección 4. Referencias

 Menú de control

 Protocolo DMX

 Especicaciones técnicas

Inhaltsverzeichnis

Sprachen:

Andere TECshow DJ-Equipment Handbücher

TECshow

TECshow STRATUS FAZER Bedienungsanleitung

TECshow

TECshow Barcob 8 Bedienungsanleitung

TECshow

TECshow iON 230B Bedienungsanleitung

TECshow

TECshow MAGIC CUBE Bedienungsanleitung

TECshow

TECshow MadBox XL 3-in-1 Bedienungsanleitung

TECshow

TECshow GOBO DERBY UV Bedienungsanleitung

TECshow

TECshow StickTriTEC Bedienungsanleitung

TECshow

TECshow UV FLOOD 30 Bedienungsanleitung

TECshow

TECshow NAVIGATOR NODE POE Bedienungsanleitung

TECshow

TECshow NAVIGATOR NODE 8 Bedienungsanleitung

TECshow

TECshow MASTERPAR 25 Bedienungsanleitung

TECshow

TECshow Cubex 360 Bedienungsanleitung

TECshow

TECshow Floor TEC Bedienungsanleitung

TECshow

TECshow QUADBAR 12 PIX Bedienungsanleitung

TECshow

TECshow BEAMPIX 14 Bedienungsanleitung

TECshow

TECshow MasterPAR Bedienungsanleitung

TECshow

TECshow ALFIE SPOT 2 Bedienungsanleitung

TECshow

TECshow nebula 1 Bedienungsanleitung

TECshow

TECshow kraftTEC Bedienungsanleitung

TECshow

TECshow ufotec Bedienungsanleitung

TECshow

TECshow HALO 80 LED Bedienungsanleitung

TECshow

TECshow ION 575 Bedienungsanleitung

TECshow

TECshow ION 280F Bedienungsanleitung

TECshow

TECshow octobeam cross Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung