TECshow ReefTEC Bedienungsanleitung

USER MANUAL

Read the user manual before turning on the product.

INTRODUCTION

Thank you for using our Products .This lighting has got the nice sculpt , efﬁcient , save

electricity and durable . It is suitable for disco, stage , building etc . Direct input of DMX512

signal to unit to allow it be controlled by any DMX512 controller. Powerful internal

programs allow customers to program freely to any different lighting project requirements

for installation or shows.

This product complies with the following standards:

IEC60598-1:2003

IEC60598-2-17:1984+A2:1990

DMX512 , Master/Slave , Sound active control mode

Professionally designed pre-programmed effects

Long-life LEDs

Strobe effect 1~20 ﬂash per sec.

4 DMX-channels

9 Dip Switches for adjusting the DMX-starting address

DMX-control via every standard DMX-controller

Ø5 LED (16R+16G+16B+16W)X2

50 000 hours LED life

Compact housing

FEATURES

SAFETY INSTRUCTIONS

Important!

Please read these instructions carefully , which includes important information about the

installation, usage and maintenance of this product.

Every person involved with the installation, operation and maintenance of this device has

to be qualiﬁed and follow the instructions of this manual .

Manufacturer will not with responsibility for those operation not according to this

Instruction.

-Always make sure that you are connecting to the proper voltage, and that the line

voltage you are connecting to is not higher than that stated on the decal or rear panel of

the ﬁxture.

- Always ground (earth) the ﬁxture electrically.

-Do not attempt to bypass the fuse, and replace the defective fuse with ones of the

speciﬁed type and rating only.

-Do not spill water or other liquids into or on to your unit.

-During long periods of non-use, disconnect the unit's main power.

-Do not attempt to operate this unit if the power cord has been frayed or broken.

-Never use the device during thunderstorms. Over voltage could destroy the device.

Always disconnect the device during thunderstorms.

-There are no user serviceable parts inside the unit. Do not open the housing or attempt

any repairs yourself.

-Maximum ambient temperature (Ta) is 35°C.

-The surface temperature of the light can reach to 50°C .

-Do not attempt to operate this unit, if it becomes damaged.

-Always be sure to mount this unit in an area that will allow proper ventilation.

-Do not directly stare at the light when it works.

-When suspending the ﬁxture above ground level, verify that the structure can hold at

least 10 times the weight of all installed devices.

-Verify that all external covers and rigging hardware are securely fastened and use an

approved means of secondary attachment such as a safety cable.

-Verify that all screws are tightly fastened.

INSTALLATION

W A R N I N G !

For safe operation, the fixture must be grounded (earthed).

Power supply

Before plugging your unit in, be sure the voltage and frequency in your area must match

the required voltage for your ﬁxture. you should be sure your unit voltages matches the

wall outlet voltage before attempting to operate your ﬁxture.

Data Connection

The ﬁxture provides 3-Pin XLR socket connector, Pin 1 is signal ground, Pin 2 is signal -,

Pin 3 is signal +.，data link as below：

3 3

signal+

Signal ground

signal-

DMX512 OUT

socket

DMX512 IN

socket

Connection method：

In DMX mode , Connect the DMX-output of the DMX controller to the DMX IN of the ﬁrst

lighting , then connect the DMX OUT of the ﬁrst lighting to the DMX IN of the second

lighting , and so on . In Master/Slave mode , it’s no need to connect controller .

If you use a controller with a 5 pin DMX output connector, you will need to use a 5 pin to

3 pin adapter.The chart below details a proper cable conversion.

Conductor 3-Pin Female(Out) 5-Pin Male(In)

Signal Ground

Pin 1

Signal -

Pin 2

Signal + Pin 3 Pin 3

Not used Pin 4: Do not use

Not used

Pin 5: Do not use

In DMX mode , insert a termination plug in the output of the last ﬁxture on the link could

reduce the reﬂection and interference. The termination plug , which is a male XLR plug

with a 120 ohm, 0.25 watt resistor soldered between pins 2 and 3.

Mounting

This ﬁxture can be mounted on a truss using a clamp in any position or against a ﬂat

surface . When suspending the ﬁxture above ground level, verify that all external covers

and rigging hardware are securely fastened and use an approved means of secondary

attachment such as a safety cable .

DIP SWITCH FUNCTION

OFF

function

9 1 2 3 4 5 6 7 8 10 Auto program/Master

9,10 1 2 3 4 5 6 7 8

Sound control (when sound off , it will

run automatically)/Master

1~9 are use for setting DMX

starting address DMX/Slave

In Master mode , set only one lighting to Master-device . and others to Slave-device , then

all lightings run follow master-device synchronously .

In DMX mode , the ﬁxture may be operated with a controller in DMX control mode . Dip 1

to Dip 9 are used for setting the starting address .

Set starting address

This DMX mode enables the use of a universal DMX controller device. Each ﬁxture requires

a "start address" from 1 to 512. A ﬁxture requiring one or more channels for control begins

to read the data on the channel indicated by the start address. For example, a ﬁxture that

uses 3 DMX channels and was addressed to start on DMX channel 100, would read data

from channels: 100, 101, 102. Choose start addresses so that the channels used do not

overlap, and note the start address selected for future reference.

Set the start address using the group of DIP switches located back of the ﬁxture. Each dip

switch has an associated value. Adding the value of each switch in the ON position will

provide the start address. Figuring out which switches to toggle ON given a speciﬁc start

address can be accomplished by determining which switch values will add up to the address

value and turning these switches on.

Dip 1 2 3 4 5 6 7 8 9

value 1 2 4 8 16 32 64 128 256

For example: Set DMX address 203

203=128+64+8+2+1

so Dip 1,Dip 2,Dip 4 ,Dip 7,Dip 8 should be dialed to ON

Refer to DMX Address Quick Reference Chart on the next page , you should set the address

dip switch more easily and quickly.

DMX ADDRESS QUICK REFERENCE CHART

0=OFF

1=ON

X=OFF or ON

128

160

192

224

256

288

320

352

384

416

448

480

129

161

193

225

257

289

321

353

385

417

449

481

130

162

194

226

258

290

322

354

386

418

450

482

131

163

195

227

259

291

323

355

387

419

451

483

100

132

164

196

228

260

292

324

356

388

420

452

484

101

133

165

197

229

261

293

325

357

389

421

453

485

102

134

166

198

230

262

294

326

358

390

422

454

486

103

135

167

199

231

263

295

327

359

391

423

455

487

104

136

168

200

232

264

296

328

360

392

424

456

488

105

137

169

201

233

265

297

329

361

393

425

457

489

106

138

170

202

234

266

298

330

362

394

426

458

490

107

139

171

203

235

267

299

331

363

395

427

459

491

108

140

172

204

236

268

300

332

364

396

428

460

492

109

141

173

205

237

269

301

333

365

397

429

461

493

110

142

174

206

238

270

302

334

366

398

430

462

494

111

143

175

207

239

271

303

335

367

399

431

463

495

112

144

176

208

240

272

304

336

368

400

432

464

496

113

145

177

209

241

273

305

337

369

401

433

465

497

114

146

178

210

242

274

306

338

370

402

434

466

498

115

147

179

211

243

275

307

339

371

403

435

467

499

116

148

180

212

244

276

308

340

372

404

436

468

500

117

149

181

213

245

277

309

341

373

405

437

469

501

118

150

182

214

246

278

310

342

374

406

438

470

502

119

151

183

215

247

279

311

343

375

407

439

471

503

120

152

184

216

248

280

312

344

376

408

440

472

504

121

153

185

217

249

281

313

345

377

409

441

473

505

122

154

186

218

250

282

314

346

378

410

442

474

506

123

155

187

219

251

283

315

347

379

411

443

475

507

124

156

188

220

252

284

316

348

380

412

444

476

508

125

157

189

221

253

285

317

349

381

413

445

477

509

126

158

190

222

254

286

318

350

382

414

446

478

510

127

159

191

223

255

287

319

351

383

415

447

479

511

Dip Switch Position

DMX CHANNEL VALUE AND FUNCTION

Channel value Function

CH1 10~255 Auto program (slow to fast)

CH2 0~10 Motor 1 don,t move

11~127 Motor 1 Clockwise rotate

128~255 Motor 1 Counter rotate

CH3 0~10 Motor 2 don,t move

11~127 Motor 2 Clockwise rotate

128~255 Motor 2 Counter rotate

CH4 0~9 No function

10~255 Select gobo

TECHNICAL SPECIFICATIONS

Power supply 220V AC , 50/60Hz

Power consumption

25 W

Light source 5 LED (16R+16G+16B+16W)X2

LED rated life 50,000 hours

Control modes DMX512, Master/Slave,Sound active

Protection rating IP20

Working temperature -25 ~ +35

Fixture dimensions 390*360*110mm

Net weight 5kg

Please note: All information is subject to change without prior notice.

AMERICAN PRO

www.american-pro.com

develops & improves products constantly.

For this reason, the specifications and consigned information in the present

user manual can be modified without notice.

TRUSTING RESULTS

Inhaltsverzeichnis

Andere TECshow Beleuchtungsausrüstung Handbücher

TECshow

TECshow MINI DERBY Bedienungsanleitung

TECshow

TECshow NEBULA FLAT 162 Bedienungsanleitung

TECshow

TECshow RAINBOW LZ Bedienungsanleitung

TECshow

TECshow QUADBAR 16 IP Bedienungsanleitung

TECshow

TECshow ALFIE STREAM Bedienungsanleitung

TECshow

TECshow HALO 1915 XL Bedienungsanleitung

TECshow

TECshow SIRIUS IP Bedienungsanleitung

TECshow

TECshow HALO 715 XL Bedienungsanleitung

TECshow

TECshow NEBULA DUAL Bedienungsanleitung

TECshow

TECshow NEBULA FLAT 81 Bedienungsanleitung

TECshow

TECshow Powerbox Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

TECshow reefTEC Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken