TEGO SYSTEM AB, Box 43, SE-261 22 Landskrona, Tel +46 (0)418 - 45 58 00, info@tego.se, www.tego.se
INSTALLATION OF DESIRED BASIC FUNKTION
Start the installation of your Roundline Master by chooseing the
right basic functions. The following are the choices:
• ”Key operated” or ”Externally controlled”
• ”Roundline Room thermostats avaliable” or ”No Roundline
Room thermostats avaliable”
Chose the mode that best suits your installation by pressing the
following buttons:
Press Mode and – at the same time to activate ”Key operated”
Press Mode and + at the same time to activate ”Externally controlled”
Press Mode and at the same time to activate ”Room thermostats
available”
Press Mode and at the same time to activate ”No room thermostats
avalabile”
DESCRIPTION OF THE DIFFERENT OPERATION MODES
Key operated:
All the teperature settings and switching between different temperature
modes is done on the Roundline Master key pad.
Externally controlled:
The temperature settings are done on the keypad. A switch
between the different temperature modes is done by an external
unit (eg a timer) through the limit switch connection.
Roundline Room Unit available:
No signals are transmitted when the ”OFF” mode is on. In ”OFF”
mode the room units take over the heaters and regulates them
according to their local settings. The Roundline Master takes over
the regulation of all the heaters when the ”ON” mode is active.
No Roundline Room Units available:
In the ”OFF” mode all heaters are regulated to 5°C, or a non
freezing mode. In ”ON” mode you can choose between day or
night temperature.
Display symbols:
Externally controlled Externally controlled
room units without room units
Key operated Key operated
room units without room units
*)Standard temperature - Day mode
Press the sun symbol (the sun symbol appears in the display) set
the desired day temoerature by using the plus and minus buttons.
The display is showing the chosen temperature with blinking num-
bers. When the numbers top blinking the new setting is activated.
**)Night temperature – Night mode
Press the moon symbol (the moon symbol appears in the
display) set the desired night temperature by using the plus and
minus buttons. The display is showing the chosen temperature
with blinking numbers. When the numbers stop blinking the new
setting is activated.
***)ON/OFF - Stand-by mode
The Roundline Master never completely. If Reco Room Units are
available the Roundline Master only show two horizontal lines in
the "OFF" mode, and the different temperature settings are shown
on the different room unit displays. If Roundline Room unit are not
available the central control will show a snowflake and the tempe-
rature 5°C, i.e. non freezing mode, in the "OFF" mode. The day
or night temperature, depending on which one is active, is always
shown in "ON" mode.
The current temperature setting and which mode is active are
displayed at all times, unless the unit is turned off or a room unit
is available. Then the display shows two horizontal lines, and the
temperature setting is shown on the different Roundline Room units.
The set temperature for each function are stored and is activated
the next tim the function is activated.
CONNECTION OF EXTERNAL CONTROL EQUIPMENT
Roundline Master has two two limit switch screw connections on
the back, one for Day or Night and one for ON or OFF. When
open is the day/night in Day mode and on/off in OFF mode.
Connect the desired equipment that you want to activate the
different temperature settings with as follows:
COMMON QUESTIONS AND TROUBLESHOOTING
The green light on the RF-plug is blinking. Why?
It means that it has no contact with any Roundline Master or Round-
line Room unit. The heater will continue to use the last setting that
was set before the communication was broken. Try to connect the
Roundline Master and the RF-plug again as above. If it still does
not work contact Tego.
How can I be sure that the heaters are connected to the
Roundline Master?
By pressing the MODE and ON/OFF buttons at the same time on
the keypad on the Roundline Master, and holding them pressed
down for 3 seconds. On all the heaters that are connected a light
on the RF-plug will turn on during the count down off 30 seconds
that are shown on the display.
I have had a power failure. Do I have to redo the installation
when the power is turned back on?
No. The RF-plug has a built-in memory. As soon as the power
comes back the system will function as before.
Day/Night On/Off
NO=Day NO=Off
))
))
Skruvhål
Dold knapp
Lysdiod
RF-enhet
20
RF-plugg is placed in
the end piece.
RF-unit
LED
Hidden button
Screw
If you only want to switch between day and
night temperature, you can close the ON/OFF
contact with a short jumper.
