Teknik FLEXI SENSOR Bedienungsanleitung

[FLEXI]SENSOR

LED SPOTLIGHT

USER MANUAL

Teknik Lighting Solutions Pty Ltd

ABN: 44 608 397 913

Tel: 1300 313 780

www.tekniklighting.com.au

INTRODUCTION

Thank you for selecting the [FLEXI]SENSOR. This is suitable only

for use with the [FLEXI] LED SPOTLIGHT. Please ensure that

the sensor is installed in accordance with the below

instructions. TEKNIK assumes no responsibility for

inappropriate use or installation of the product, including any

associated damage caused.

SPECIFICATIONS

Input Voltage

Ambient Light

Time Delay

Detection Range

Detection Angle

Motion Detection Speed

Recommended Installation Height

<10-2000 Lux (adjustable)

min: 10sec ±3sec, max: 12min±3min

2 - 12m (< 24oC) (adjustable)

180o

0.6 ~ 1.5m/s

1.8m-2.5m

5V DC

INSTALLATION

Attach the sensor

to the bottom of the

[FLEXI] fitting ensuring

all pins are aligned.

Turn the [FLEXI] ON and follow the test and

function setting instructions.

1Remove

the cap of

the [FLEXI]

fitting.

FUNCTIONS

LUX

Use this setting to adjust the sensor according to ambient light. When

the lux dial Is set to the moon position the [FLEXI] will only operate

when the ambient light level is below 10lux. When the lux dial is set to

the sun position, the [FLEXI] will operate with an ambient light up to

2000lux.

SENSITIVITY

Use this setting to adjust the sensitivity level. Low sensitivity will detect

motion within 2m and high sensitivity will detect motion up to 12m.

TIME

Use this setting to adjust how long the [FLEXI] stays on after motion is

detected. Minimum ON time is 10sec ±3sec and maximum ON time is

12mins ±3min.

TEST

For testing in daylight turn lux dial to the ÔsunÕ position, sensitivity dial

to max (+) and time dial to (-). Adjust the angle and orientation of the

sensor as desired. Make final lux, sensitivity and time adjustments to

your preferred settings.

To override the sensor operation, turn the power on, activate the light

via the sensor so it is actually illuminated, then switch the power

off/on/off/on within 3 seconds. The [FLEXI] will now remain on until the

power is switched off or put back into sensor mode. To resume

sensor operation, turn off the power for 10 seconds then back on.

Manual Override

Inhaltsverzeichnis

Andere Teknik Scheinwerfer Handbücher

Teknik

Teknik FLEXI Bedienungsanleitung

Beliebte Scheinwerfer Handbücher anderer Marken

Guangzhou Yinhe Lighting&Sound Equipment Factory

Guangzhou Yinhe Lighting&Sound Equipment Factory NE-204 Bedienungsanleitung

LIVARNO home

LIVARNO home 375304 2101 Originalbetriebsanleitung

Cameo

Cameo CLQS40WW Bedienungsanleitung

Leviton

Leviton Ellipsoid 5/50 Bedienungsanleitung

Monacor

Monacor img Stage Line PARL-56PDX/CR Bedienungsanleitung

Vector

Vector SL3AKV Bedienungsanleitung

Quantum

Quantum Q262 Betriebshandbuch

Philips

Philips Vari-lite VL3015LT Bedienungsanleitung

EUROSPOT

EUROSPOT C51 Bedienungsanleitung

DTS

DTS MINI BRICK ARC Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation VISIBEAM II Handbuch

ACME

ACME LED-MS350B Bedienungsanleitung

EuroLite

EuroLite Akku flat light 1 Bedienungsanleitung

Commercial Electric

Commercial Electric SPTM-1401 Bedienungsanleitung

Vision & Control

Vision & Control SLB-500-W5K7-P-SL Bedienungsanleitung

Craftsman

Craftsman CMXLSB10 Bedienungsanleitung

EuroLite

EuroLite LED SLS-144 UV Floor Spot Bedienungsanleitung

Ignition

Ignition WAL-L412 BP Bedienungsanleitung