TekTone CM800 Handbuch

CM800/CM900

EmergencyCallSignalingSystem

Operation, Installation and Service Manual

APPLICATION: The CM800/CM900 Emergency Call Signaling System is designed for

elderly housing, retirement facilities or wherever an Emergency Call System is required. The

Emergency Call System provides audible and visual indication of all calls originating in the

system.TheCM800/CM900Annunciatorcontains lampsfor call indication,as well asa tone-

off switch and audible tone signaling devices.

IL514

SECTION D

Rev. 12 - 01/2009

Website:

www.tektone.NET

Email:

[email protected]

For Technical Assistance:

1-800-332-6608

Technical Assistance Email:

[email protected]

277 Industrial Park Road

Franklin, NC 28734

(828) 524-9967

(800) 327-8466

Fax (828) 524-9968

Operation, Installation and Service Manual

No part of this publication may be copied without the express written permission of TekTone®Sound & Signal Mfg., Inc. The content

of this manual is furnished for informational use only, is subject to change without notice, and should not be construed as a

commitment by TekTone®Sound & Signal Mfg., Inc. TekTone®Sound & Signal Mfg., Inc. assumes no responsibility or liability for

any errors or inaccuracies that may appear in this documentation.

TekTone, the TekTone logo, Tek-Call, Tek-Care, Tek-Check-In, Tek-Com, Tek-Digicare, Tek-Door, Tek-Entry III, Tek-Guard,

Tek-Micro, Tek-Micro II, Tek-MMARS II, TekNIOS, TekNIOS II, Tek-Paging, Tek-Phone, Tek-Safe, Tek-Select II, Tek-Sentry,

Tek-Sound, Tek-Status, Tek-Trio and Tek-View are either registered trademarks or trademarks of TekTone®Sound & Signal Mfg.,

Inc. in the United States and/or other countries. All other trademarks are the property of their respective owners.

TekTone®Sound & Signal Mfg., Inc., 277 Industrial Park Road, Franklin, North Carolina 28734, USA.

IL514CM800/CM900 Emergency CallSystem Manual • iii

System Operating Instructions........................................................ 1

CM800, CM900 Annunciators............................................................1

SF117 series, SF118 series Emergency Call Stations .........................1

SF154 Emergency Call Station ...........................................................1

IR019, IR019B Remote Annunciator Tone Speakers ........................2

LI381 Corridor Light...........................................................................2

LI382 Corridor Light...........................................................................2

LI118B, LI123B Corridor Lights ........................................................2

BE005, BE007 Corridor Bells .............................................................2

System Installation ......................................................................... 3

Installation Procedure..........................................................................3

Equipment Locations...........................................................................3

Wiring Installation ...............................................................................3

Housing Installation .............................................................................4

Wire Checkout ..................................................................................4

Connections Checkout ........................................................................4

Illustrations

Figure 1—Master Panel Housing Chart and Wall Cut-Out Details ......5

Figure 2—Ring and Back Box for SF117 series, SF118 series

and SF154 Emergency Call Stations.........................5

Figure 3—Ring and Back Box for IR019 & IR019B

Tone Speakers, and LI118B, LI123B,

LI381 & LI382 Corridor Lights ................................5

Figure 4—Emergency Call Hook-Up Diagram with SF117/2 series,

SF118 series & SF154 Emergency Switches,

and LI381 & LI118B Corridor Lights ......................6

Figure 5—Emergency Call Hook-Up Diagram with

SF117/4 series Continuous Duty Door Release,

LI381 Corridor Light, LI123B Corridor

Light with Buzzer, and BE005 Corridor Bell ............7

Figure 6—Emergency Call Hook-Up Diagram with

SF117/2 series Continuous Duty Door Release,

LI381 Corridor Light, Smoke Detector,

and BE007 Corridor Bell...........................................8

Figure 7—Connection Diagram for Parallel CM800 Panels ................8

Table of Contents ————————————————————

IL514CM800/CM900 Emergency CallSystem Manual •1

System Operating Instructions ——————————————

System operators must read the following operating instructions concerning system

equipment and terms used in conjunction with the equipment.

CM800, CM900 Annunciators

Answer Emergency Calls:

Emergency calls are indicated by simultaneous operation of the following signals:

• Steady illumination of the associated station selector lamp, which is marked to

indicate call origin.

• Rapidly pulsating audible tone. The audible call signal may be canceled by pressing

the tone-off button. The tone-off light will illuminate to indicate that tone is silenced.

Thetone-offbuttonmaybepressedatanytimetoverifyoperationofthetone-offlamp.

Call signals may only be canceled at the point of origin, and all calls must be answered in

person.

Test Station Annunciator Lamp (if so equipped):

One lamp test button is provided on each panel of annunciator lamps. Press the lamp

test button—all annunciator lamps on that panel should be illuminated.

Improper Operation:

If the CM800 or CM900 Annunciator fails to operate as described, contact qualified

maintenance personnel. If a malfunction occurs during a call-in, causing a lack of

indication of call origin on the master station, first determine the origin of the call by

observing which corridor light is illuminated, and then inform qualified personnel.

SF117 series, SF118 series Emergency Call Stations

Place an Emergency Call:

Pullthe call cord andwait for anAttendant. (Note:TheSF118series station has a red call-

placed light that illuminates when the cord is pulled.)

Reset the Station:

Push the slide switch up.

Improper Operation:

If the station does not operate as described, contact qualified personnel. There are no

user serviceable parts on SF117 series and SF118 series Emergency Call Stations.

SF154 Emergency Call Station

Place an Emergency Call:

Press the switch in so that the red area of the switch is visible, and wait for an Attendant.

Reset the Station:

Press the switch out so that the red area of the switch is not visible.

Improper Operation:

If the station does not operate as described, contact qualified personnel. There are no

user serviceable parts on the SF154 Emergency Call Station.

IR019, IR019B Remote Annunciator Tone Speakers

Emergency Calls:

Emergency calls are indicated by a rapidly pulsating audible tone. The audible tone

signal can be silenced by pressing the tone-off switch. (The IR019 is not equipped with

a tone-off light.) The IR019 and IR019B tone mimics the annunciator tone—either

steady or pulsing.

Improper Operation:

If the speaker does not operate as described, contact qualified personnel. There are no

user serviceable parts on the IR019 and IR019B Remote Annunciator Tone Speakers.

LI381 Corridor Light

Emergency Calls:

Emergency calls are indicated by steady illumination of the corridor light associated

with the calling station.

Improper Operation:

If the corridor light does not operate as described, contact qualified service personnel.

There are no user serviceable parts on the LI381 Corridor Light, other than bulbs.

LI382 Corridor Light

Emergency Calls:

Emergency calls are indicated by steady illumination of the corridor light associated

with the calling station. The second light can be used for other call types initiated from

the same zone.

Improper Operation:

If the corridor light does not operate as described, contact qualified service personnel.

There are no user serviceable parts on the LI382 Corridor Light, other than bulbs.

LI118B, LI123B Corridor Lights

Emergency Calls:

Emergency calls are indicated by steady illumination of the corridor light and a steady

buzzer.

Improper Operation:

If the corridor light does not operate as described, contact qualified service personnel.

There are no user serviceable parts on the LI118 and LI123B Corridor Lights, other

than bulbs.

BE005, BE007 Corridor Bells

Emergency Calls:

Emergency calls are indicated by a steady ringing of the corridor bells.

Improper Operation:

If the corridor bell does not operate as described, contact qualified service personnel.

There are no user serviceable parts on the BE005 and BE007 Corridor Bells.

System Operating Instructions

IL514CM800/CM900 Emergency CallSystem Manual •3

Installation Procedure

• Read the following instructions concerning system equipment, and determine

installation methods before proceeding.

• Determine equipment locations.

• Install wiring.

• Install housings.

• Check wires.

• Connect equipment.

• Check connections.

• Applypower.

• Check system operation.

Equipment Locations

CM800, CM900 Annunciator:

Locate CM800 and CM900 Annunciators within easy reach of operating personnel.

Permitted operating temperature of 10°C–30°C must not be exceeded.

SF117 series, SF118 series, SF154 Emergency Call Stations:

Locate emergency stations where convenient for operation. Avoid areas where direct

contact with water may occur. The SF117 series and SF118 series include a 6' long pull

cord, permitting installation high enough to provide easy operation by the staff and by

seated or prone patients. The SF154 is operated by means of a push button located on

the station.

IR019, IR019B Remote Annunciator Tone Speakers:

Locate annunciator tone speakers as needed and where convenient for operation.

Location must provide for unobstructed visibility of the tone-off indicator (IR019B).

LI381, LI382, LI118B, LI123B Corridor Lights:

Locate corridor lights in the corridor above or beside the door of the associated rooms.

Location must provide unobstructed visibility of the corridor light in both directions.

PK2019 Control Unit:

The PK2019 may be surface mounted adjacent to the SS106, if necessary. If remotely

located, cable run from PK2019 to CM800/CM900 must not exceed 100'.

PK601A Power Supply:

Surface mount the PK601A adjacent to the SS106 and PK2019.

PK612A DC Flasher:

Surface mount the PK612A adjacent to the SS106 and PK2019.

BE005/BE007 Corridor Bells:

Locate BE005 and BE007 Corridor Bells in corridor above door height. Location in

corridor will be determined by the number of bells required on each floor.

SS106 Transformer:

Locate SS106 in an accessible area near a source of 117 VAC. Observe local codes.

Wiring Installation

Runwiring conduitfrom corridor lightto corridorlight andterminate atthe CM800 orCM900

annunciator panel. Select conduit size according to the application, as shown in wiring

diagrams in this booklet. Observe local codes.

System Installation ——————————————————––

PK2019 Options:

• For 30-second delay before tone, connect terminal A to terminal N.

• Forsteadytone,connectterminalWtoterminalN.Iftheannunciatorlampisflashing,

the tone will be intermittent despite terminal W connection.

Housing Installation

CM800, CM900 Annunciators:

Flush Wall Mount—Provide a wall cutout as shown in Figure 1. Fit the back box and

frame assembly into the prepared opening. Fasten the assembly in place. Note:The back

box must beTekTone®OH200 Series.

Surface Wall Mount—Fasten the back box and frame assembly to the wall through the

holes provided in back of the box, using suitable fasteners. Note: Back box must be

TekTone®OH300Series.

SF117 series, SF118 series, SF154 Emergency Call Stations:

Install single gang ring (or single gang ring and double gang box) as shown in Figure 2

for each emergency call station in system. Minimum dimensions of back box must not

be less than 4"×4"×1.5". Minimum opening on ring must not be less than 1.75"×2.75".

Minimum clearance from live parts of the station to dead metal parts must not be less

than 0.5".

IR019, IR019B Remote Annunciator Tone Speakers:

Install double gang ring (or double gang ring and double gang box) as shown in Figure 3

for each tone speaker station. Minimum dimensions of back box must not be less than

4"×4"×1.5".

LI118B, LI123B Corridor Lights:

Install double gang ring (or double gang ring and double gang box) as shown in Figure 3

for each tone speaker station. Minimum dimensions of back box must not be less than

4"×4"×1.75".

LI381, LI382 Corridor Lights:

Install double gang ring (or double gang ring and double gang box) as shown in Figure 3

for each corridor light. Minimum dimensions of back box must not be less than

4"×4"×1.5". Minimum opening on ring must not be less than 2.75"×2.75". Minimum

clearance from live parts of the station to dead metal parts must not be less than 0.5".

BE005, BE007 Corridor Bells:

Install a standard 4" Bell Box.

Wire Checkout

Use an ohmmeter or other continuity checking device to test wires for shorts or grounds.

If shorts or grounds are encountered, find and correct the problems before continuing.

Make sure the minimum number of conductors that are needed for all of the equipment

being used in the system are available.

Connections Checkout

Re-check all connections to equipment. If all wires and connections are satisfactory, connect

theprimary coil ofthe SS106Transformertoa source of117VAC60 Hz (30VAmax.).

System Installation

IL514CM800/CM900 Emergency CallSystem Manual •5

Figure 1—Master Panel Housing Chart and Wall Cut-Out Details

Housing Wall Opening

Flush Surface Width (B) Height

OH202 OH302 8.5" 16.25"

OH203 OH303 12.5" 16.25"

OH204 OH304 16.5" 16.25"

OH205 OH305 20.5" 16.25"

Figure 2—Ring and Back Box for

SF117 series, SF118 series and SF154

Emergency Call Stations

Installring with panel mounting holesattop and bottom, as shown.

Figure 3—Ring and Back Box for

IR019 & IR019B Tone Speakers, and

LI118B, LI123B, LI381 & LI382 Corridor Lights

Installring with panel mounting holesattop and bottom, as shown.

16"

3.75"

Finished Wall

4" min.

16.25"

Inmasonrywalls,install0.5"×4"wood

fillersat topandbottomofopeningfor

housingattachment.

Finished Floor

66"

16.25"

Notes:

1. Use16VACconnectionson SS106Transformer.

2. Wiring may be #22 except where shown otherwise.

3. PK2019 Annunciator Control Unit may be mounted outside of

annunciatorenclosure.

4. Switches are shown in the OFF position.

5. PK612Aandassociated wiring isoptional and needs onlyto be

installed if a flash common is needed.

Wiring Diagram for IR019, IR019B and PK2019

(Disregardwiringfortone-offlampifwiringIR019.)

Figure 4—Emergency Call Hook-Up Diagram with SF117/2 series, SF118 series &

SF154 Emergency Switches, and LI381 & LI118B Corridor Lights

IL514 General Wiring Figure 4 Rev1 051106 1

TONE

SPEAKER

PK2019

Speaker

45 Ohm

Tone-Off

Lamp

Tone-Off

Button

IR019B

COMMON

LI381

DOME

LAMP LI381

DOME

LAMP

SF118/2B

Call Placed

SF118/2B

Emergency Switch

LI118B

DOME

LAMP

w/ BUZZER

ANNUNCIATOR

LAMPS

TEST

BUTTON

#18 (optional, see Note 5)

FACTORY CONNECTED NOTE: PM110/4N

Modules only!

PK2019

COMMON

NORMALLY OPEN RELAY

OUTPUTS

NORMALLY CLOSEDR3

WTONE-

OFF

LAMP

TONE-

OFF

BUTTON

#18

16 VAC

SS106

TRANSFORMER

(See Note 1)

117 VAC

PK612A

(optional, see Note 5)

SF117/2(B,C)

or SF154

Emergency Switch

LI381

DOME

LAMP

SF117/2(B,C)

or SF154

Emergency Switch

SF117/2(B,C)

or SF154

Emergency Switch

SF117/2(B,C)

or SF154

Emergency Switch

Light

LI381

DOME

LAMP

SF118/4B

Call Placed

SF118/4B

Emergency Switch

Light

Door

Release

PK601A

SS106

TRANSFORMER

24VAC 117VAC

#18

Andere Handbücher für CM800

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere TekTone Notrufnummer Handbücher

TekTone

TekTone Tek-CARE 550 Bedienungsanleitung

Beliebte Notrufnummer Handbücher anderer Marken

Dosch&Amand

Dosch&Amand DA1450 Bedienungsanleitung

Viking

Viking E-1600A series Montage- und Bedienungsanleitung

LogicMark

LogicMark GUARDIAN ALERT 911 Bedienungsanleitung

Rath

Rath 2500-205D Bedienungsanleitung

Wind n Go

Wind n Go 7700 Bedienungsanleitung

Rath

Rath 2100-CPV Bedienungsanleitung

Wind Crest

Wind Crest ILO1 Bedienungsanleitung

Bell System

Bell System Master 200Plus Bedienungsanleitung

Linear

Linear PERS-3600 Montageanleitung

ooma

ooma Safety Phone 700-0129-203 Bedienungsanleitung

CareTech

CareTech Gina Bedienungsanleitung

Rath

Rath SmartPhone VI Kurzanleitung

Paso

Paso PA8506-V Bedienungsanleitung

JNY Safetycare

JNY Safetycare FDC Bedienungsanleitung

Rath

Rath 2100-TL9 Bedienungsanleitung

Eldat

Eldat Easywave Fon Alarm Bedienungsanleitung

Merak

Merak MMk-656 Bedienungsanleitung

Assistive Technology Services

Assistive Technology Services TOUCH N TALK FD Montageanleitung