Tektronix TMT4 Handbuch

TMT4 Margin Tester Installation and Safety

Instructions

Documentation

Product documentation

The following table lists the primary product specific documentation available for your product. These and other user documents are

available for download from www.tek.com. Other information, such as demonstration guides, technical briefs, and application notes, can

also be found at www.tek.com.

Document Content

Installation and Safety Instructions Safety, compliance, and basic introductory information for hardware

products.

User Operating information for the product.

Specifications and Performance Verification Technical Reference Instrument specifications and performance verification instructions

for testing instrument perfomance.

API Programmer UI API commands for remotely controlling the instrument. Available

from a web browser.

Declassification and Security Instructions Information about the location of memory in the instrument.

Instructions for declassifiying and sanitizing the instrument.

How to find your product documentation

1. Go to www.tek.com.

2. Click Download in the green sidebar on the right side of the screen.

3. Select Manuals as the Download Type, enter your product model, and click Search.

4. View and download your product manuals. You can also click the Product Support Center and Learning Center links on the page for

more documentation.

Power, environmental, and physical specifications

Power

Input voltage 100-240 V

Frequency 50-60 Hz

Power 200 W maximum

WARNING:

To reduce the risk of fire and shock, ensure that the mains power supply voltage fluctuations do not exceed 10% of the operating

voltage range.

Environmental

Temperature

Table continued…

tek.com

*P071377500*

071-3775-00

Operating 0°C to +50°C, with 15°C/hour maximum gradient, non-condensing

Non-operating -40°C to +71°C, with 30°C/hour maximum gradient

Required instrument clearance

Rear None

Bottom Feet provide sufficeint clearance. Do not operate instrument without feet.

Sides 50.8 mm (2 in)

Top None

Humidity

Operating 5% to 95% relative humidity (% RH) at up to +30°C

5% to 75% RH above +30°C up to +40°C

45% RH above +40°C up to 50°C, non-condensing

Non-operating 5% to 95% RH (Relative Humidity) at up to +30°C

5% to 45% RH above +40°C up to +71°C, non-condensing

Altitude

Operating Up to 3,000 meters

Non-operating Up to 12,000 meters

Physical

Measure Instrument only

Weight 3.07 kg (6.77 lbs)

Dimension With protective cover, handle, and feet No protective cover,with 50 Ω terminators

Height 220 mm (8.66 in) 200 mm (7.87 in)

Width 200 mm (7.87 in) 190 mm (7.48 in)

Depth 147 mm (5.79 in) 140 mm (5.51 in)

Power, environmental, and physical specifications

Front panel controls and connectors

The front panel provides access to power button, trigger and signal inputs and outputs, and touchscreen display.

Description

1Power button. LED color indicates power mode.

Off: Unplugged (unplug the power cord to remove power completely)

Amber: Standby

Blue: On

2 PCIe high density connector

3 USB 2.0 type A port.

4Banana type ground connection. Discharge the static voltage from your body by wearing a grounded antistatic wrist strap while

connecting and disconnecting cables and adapters.

5 (Not yet available) Trigger Out +1.25 V, 50 Ω

6 (Not yet available) Trigger In +3.3 V, 50 Ω

7 5" LCD touch screen provides access to basic controls and test results.

Front panel controls and connectors

Rear panel connectors

The rear panel connectors provide access to power and LAN.

Description

1 LAN. 10/100/1000 Base-T Ethernet port for remote connection to a PC.

2 SD memory card slot. This slot will be used for core storage needs. Removable for sensitive purposes related to declassification as

needed. Remove screws to access card.

3 Power connector. 100-240V, 50-60Hz, 200 W maximum

4 Fan vents.

Setup and installation

Connect and turn on

CAUTION: Do not disconnect a device under test when the instrument is powered on. If a disconnection occurs when power is

on, the instrument must be powered off, and then powered back on after DUT connectivity is restored.

Follow these steps after you unpack the instrument to turn it on, connect, and get started. This requires an Ethernet connection.

1. Plug in an Ethernet cable to the LAN connector on the rear panel of the instrument and then directly to the host PC or to an Ethernet

network.

2. Plug in the supplied power cord to the power connector on the rear of the instrument and to an appropriate power source.

3. Push the Power button on the front panel to turn on the instrument. The Power button LED color indicates the power mode of the

instrument. Amber is Standby. Blue is On. No light means the instrument is unplugged and Off.

4. When you are turning on the instrument for the first time, the following screen should appear. Write down the IP address shown on the

screen of your instrument.

Rear panel connectors

5. Open a browser window on a PC and enter the IP address from your instrument.

6. Enter the serial number of your instrument into the Factory Password field. Then enter a new password in the New Password field.

Reneter the password. Be sure to remember the new password or record and place it in a secure location. It will be needed each time

the instrument is remotely accessed.

7. A Welcome screen with the instrument menus will appear after you click the Change Password button. See the User manual available

on www.tek.com/manuals for additional operating and fixture information.

Remote control through the API

You can program and control your instrument using API commands. Do the following to access the web UI for the API:

1. Enter the IP address of the instrument into a PC browser window.

2. Then add :5000/api/docs to the IP address. Example: 123.00.1.1:5000/api/docs

3. The web UI for the API will appear.

See the TMT4 Margin Tester User Manual at www.tek.com for more detailed information about using the API.

Setup and installation

Important safety information

This manual contains information and warnings that must be followed by the user for safe operation and to keep the product in a safe

condition.

To safely perform service on this product, see the Service safety summary that follows the General safety summary.

General safety summary

Use the product only as specified. Review the following safety precautions to avoid injury and prevent damage to this product or any

products connected to it. Carefully read all instructions. Retain these instructions for future reference.

This product shall be used in accordance with local and national codes.

For correct and safe operation of the product, it is essential that you follow generally accepted safety procedures in addition to the safety

precautions specified in this manual.

The product is designed to be used by trained personnel only.

Only qualified personnel who are aware of the hazards involved should remove the cover for repair, maintenance, or adjustment.

Before use, always check the product with a known source to be sure it is operating correctly.

This product is not intended for detection of hazardous voltages.

Use personal protective equipment to prevent shock and arc blast injury where hazardous live conductors are exposed.

While using this product, you may need to access other parts of a larger system. Read the safety sections of the other component manuals

for warnings and cautions related to operating the system.

When incorporating this equipment into a system, the safety of that system is the responsibility of the assembler of the system.

To avoid fire or personal injury

Use proper power cord.

Use only the power cord specified for this product and certified for the country of use. Do not use the provided power cord for other

products.

Ground the product.

This product is indirectly grounded through the grounding conductor of the mainframe power cord. To avoid electric shock, the grounding

conductor must be connected to earth ground. Before making connections to the input or output terminals of the product,ensure that the

product is properly grounded. Do not disable the power cord grounding connection.

Power disconnect.

The power cord disconnects the product from the power source. See instructions for the location. Do not position the equipment so that it is

difficult to operate the power cord; it must remain accessible to the user at all times to allow for quick disconnection if needed.

Observe all terminal ratings.

To avoid fire or shock hazard, observe all rating and markings on the product. Consult the product manual for further ratings information

before making connections to the product.

Do not operate without covers.

Do not operate this product with covers or panels removed, or with the case open. Hazardous voltage exposure is possible.

Important safety information

Avoid exposed circuitry.

Do not touch exposed connections and components when power is present.

Do not operate with suspected failures.

If you suspect that there is damage to this product, have it inspected by qualified service personnel.

Disable the product if it is damaged. Do not use the product if it is damaged or operates incorrectly. If in doubt about safety of the product,

turn it off and disconnect the power cord. Clearly mark the product to prevent its further operation.

Examine the exterior of the product before you use it. Look for cracks or missing pieces.

Use only specified replacement parts.

Do not operate in wet/damp conditions.

Be aware that condensation may occur if a unit is moved from a cold to a warm environment.

Do not operate in an explosive atmosphere.

Keep product surfaces clean and dry.

Remove the input signals before you clean the product.

Provide proper ventilation.

Refer to the installation instructions in the manual for details on installing the product so it has proper ventilation.

Slots and openings are provided for ventilation and should never be covered or otherwise obstructed. Do not push objects into any of the

openings.

Provide a safe working environment

Always place the product in a location convenient for viewing the display and indicators.

Be sure your work area meets applicable ergonomic standards. Consult with an ergonomics professional to avoid stress injuries.

Use care when lifting and carrying the product. This product is provided with a handle or handles for lifting and carrying.

Terms in this manual

These terms may appear in this manual:

WARNING: Warning statements identify conditions or practices that could result in injury or loss of life.

CAUTION: Caution statements identify conditions or practices that could result in damage to this product or other property.

Terms on the product

These terms may appear on the product:

•DANGER indicates an injury hazard immediately accessible as you read the marking.

• WARNING indicates an injury hazard not immediately accessible as you read the marking.

• CAUTION indicates a hazard to property including the product.

Risk assessment warnings and information

Symbols on the product

When this symbol is marked on the product, be sure to consult the manual to find out the nature of the potential

hazards and any actions which have to be taken to avoid them. (This symbol may also be used to refer the user to

ratings in the manual.)

The following symbols(s) may appear on the product.

Service safety summary

The Service safety summary section contains additional information required to safely perform service on the product. Only qualified

personnel should perform service procedures. Read this Service safety summary and the General safety summary before performing any

service procedures.

To avoid electric shock.

Do not touch exposed connections.

Do not service alone.

Do not perform internal service or adjustments of this product unless another person capable of rendering first aid and resuscitation is

present.

Disconnect power.

To avoid electric shock, switch off the product power and disconnect the power cord from the mains power before removing any covers or

panels, or opening the case for servicing.

Use care when servicing with power on.

Dangerous voltages or currents may exist in this product. Disconnect power, remove battery (if applicable), and disconnect test leads

before removing protective panels, soldering, or replacing components.

Verify safety after repair.

Always recheck ground continuity and mains dielectric strength after performing a repair.

Compliance information

This section lists the safety and environmental standards with which the instrument complies. This product is intended for use by

professionals and trained personnel only; it is not designed for use in households or by children.

Compliance questions may be directed to the following address:

Tektronix, Inc.

PO Box 500, MS 19-045

Beaverton, OR 97077, USA

tek.com

Symbols on the product

Safety compliance

This section lists the safety standards with which the product complies and other safety compliance information.

EU declaration of conformity – low voltage

Compliance was demonstrated to the following specification as listed in the Official Journal of the European Union:

Low Voltage Directive 2014/35/EU.

• EN 61010-1. Safety Requirements for Electrical Equipment for Measurement, Control, and Laboratory Use – Part 1: General

Requirements

U.S. nationally recognized testing laboratory listing

• UL 61010-1. Safety Requirements for Electrical Equipment for Measurement, Control, and Laboratory Use – Part 1: General

Requirements

Canadian certification

• CAN/CSA-C22.2 No. 61010-1. Safety Requirements for Electrical Equipment for Measurement, Control, and Laboratory Use – Part 1:

General Requirements

Additional compliances

• IEC 61010-1. Safety Requirements for Electrical Equipment for Measurement, Control, and Laboratory Use – Part 1: General

Requirements

Equipment type

Test and measuring equipment.

Safety class

Class 1 – grounded product.

Pollution degree description

A measure of the contaminants that could occur in the environment around and within a product. Typically the internal environment inside a

product is considered to be the same as the external. Products should be used only in the environment for which they are rated.

• Pollution Degree 1. No pollution or only dry, nonconductive pollution occurs. Products in this category are generally encapsulated,

hermetically sealed, or located in clean rooms.

• Pollution Degree 2. Normally only dry, nonconductive pollution occurs. Occasionally a temporary conductivity that is caused by

condensation must be expected. This location is a typical office/home environment. Temporary condensation occurs only when the

product is out of service.

• Pollution Degree 3. Conductive pollution, or dry, nonconductive pollution that becomes conductive due to condensation. These are

sheltered locations where neither temperature nor humidity is controlled. The area is protected from direct sunshine, rain, or direct

wind.

• Pollution Degree 4. Pollution that generates persistent conductivity through conductive dust, rain, or snow. Typical outdoor locations.

Pollution degree rating

Pollution Degree 2 (as defined in IEC 61010-1). Rated for indoor, dry location use only.

IP rating

IP20 (as defined in IEC 60529).

Safety compliance

Measurement and overvoltage category descriptions

Measurement terminals on this product may be rated for measuring mains voltages from one or more of the following categories (see

specific ratings marked on the product and in the manual).

• Measurement Category II. For measurements performed on circuits directly connected to the low-voltage installation.

• Measurement Category III. For measurements performed in the building installation.

• Measurement Category IV. For measurements performed at the source of low-voltage installation.

Note: Only mains power supply circuits have an overvoltage category rating. Only measurement circuits have a measurement

category rating. Other circuits within the product do not have either rating.

Mains overvoltage category rating

Overvoltage Category II (as defined in IEC 61010-1).

Environmental compliance

This section provides information about the environmental impact of the product.

Product end-of-life handling

Observe the following guidelines when recycling an instrument or component:

Equipment recycling Production of this equipment required the extraction and use of natural resources. The equipment may

contain substances that could be harmful to the environment or human health if improperly handled at the

product’s end of life. To avoid release of such substances into the environment and to reduce the use of

natural resources, we encourage you to recycle this product in an appropriate system that will ensure that

most of the materials are reused or recycled appropriately.

This symbol indicates that this product complies with the applicable European Union requirements according to Directives

2012/19/EU and 2006/66/EC on waste electrical and electronic equipment (WEEE) and batteries. For information about

recycling options, check the Tektronix Web site (www.tek.com/productrecycling).

Battery recycling This product contains a small installed lithium metal button cell. Please properly dispose of or recycle the

cell at its end of life according to local government regulations.

Perchlorate materials This product contains one or more type CR lithium batteries. According to the state of California, CR

lithium batteries are classified as perchlorate materials and require special handling. See www.dtsc.ca.gov/

hazardouswaste/perchlorate for additional information.

Transporting batteries

The small lithium primary cell contained in this equipment does not exceed 1 gram of lithium metal content per cell.

The cell type has been shown by the manufacturer to comply with the applicable requirements of the UN Manual of Tests and Criteria

Part III, Sub-section 38.3. Consult your carrier to determine which lithium battery transportation requirements are applicable to your

configuration, including to its re-packaging and re-labeling, prior to reshipment of the product by any mode of transport.

Cleaning

Use a dry, soft cotton cloth to clean the outside of the unit. If any dirt remains, use a cloth or swab dipped in a 75% isopropyl alcohol

solution. Use a swab to clean narrow spaces around controls and connectors. Do not use any liquid cleaning agents or chemicals that

could damage the touchscreen, case, controls, markings or labels, or possibly infiltrate the case.

Environmental compliance

Andere Handbücher für TMT4

Inhaltsverzeichnis

Sprachen:

Andere Tektronix Prüfgeräte Handbücher

Tektronix

Tektronix 465B Bedienungsanleitung

Tektronix

Tektronix 466 Bedienungsanleitung

Tektronix

Tektronix 2232 Bedienungsanleitung

Tektronix

Tektronix 2 Series Montage- und Wartungsanleitung

Tektronix

Tektronix 2440 Produktinformationsblatt

Tektronix

Tektronix MSO24 Gebrauchsanweisung

Tektronix

Tektronix 485 Bedienungsanleitung

Tektronix

Tektronix TAS 200 Bedienungsanleitung

Tektronix

Tektronix CSA 907A Bedienungsanleitung

Tektronix

Tektronix 7844 Bedienungsanleitung

Tektronix

Tektronix 4000 Series Bedienungsanleitung

Tektronix

Tektronix 420 Bedienungsanleitung

Tektronix

Tektronix 432 Service-Handbuch

Tektronix

Tektronix TBS2000B Series Einrichtungshandbuch

Tektronix

Tektronix 454A Bedienungsanleitung

Tektronix

Tektronix 2212 Bedienungsanleitung

Tektronix

Tektronix 2467 Bedienungsanleitung

Tektronix

Tektronix MSO70000C Series Bedienungsanleitung

Tektronix

Tektronix 7140 Bedienungsanleitung

Tektronix

Tektronix TDS 500D Gebrauchs- und Pflegehandbuch

Tektronix

Tektronix TMT4 Gebrauchs- und Pflegehandbuch

Tektronix

Tektronix WVR5250 Bedienungsanleitung

Tektronix

Tektronix DPO3000 Series Bedienungsanleitung

Tektronix

Tektronix TDS1000 Series Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Vernier

Vernier Go Direct Voltage Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung