Telecor VS-600 Bedienungsanleitung

Telecor Inc.

1114 Westport Cr.

Mississauga, Ontario

Canada, L5T 1G1

Tel: (905) 564-0801

Fax: (905) 564-0806

www.telecor.com

For the VS-600 Resident Unit

November 2009

Revision 0.1 (PRELIMINARY)

VS-600 Resident Unit

Manual

LIMITED WARRANTY

Telecor Inc. warrants all products bearing the Telecor name to be free from defects of material and

workmanship under normal use and service for a period of one year from date of delivery. Telecor will

repair or replace (at our option), free of charge, any unit that is found to be defective and returned to us

under warranty. Telecor warrants all other products made by others, and distributed by us, to be covered

by the manufacturers' warranty period.

This warranty shall not apply to any Telecor products that have been subject to misuse, neglect, accident,

modification, water, fire, lightning, paint, or used in violation of instructions furnished, repaired or altered

outside of the factory. This warranty does not cover batteries, bulbs, fuses or damage caused by batteries

used in connection with the product. Telecor reserves the right to make the final decision on whether

there is a defect in materials or workmanship, and whether or not the product returned is within the

warranty period.

This warranty covers bench repairs only. Telecor will not be responsible for any costs incurred involving

on-site service calls. Repair or replacement by others, fire, transportation, labour charges, indemnity, etc.,

are not covered by this warranty and no responsibility for same will be assumed by us. Our liability does

not extend to consequential damage.

AUTHORIZED REPAIR STATION:

All participating Distributors and Dealers are authorized to accept Telecor products for return to us for

repair or replacement, or customers may return goods to us directly, providing that return authorization

has been obtained.

U.S. customers are required to ship any returns or repairs to:

Telecor Inc.

2434 Jerauld Avenue * U.S. customers must not

Niagara Falls, New York return products to Canada

USA, 14305

Canadian and all International customers are required to ship any returns or repairs to:

Telecor Inc.

1114 Westport Crescent

Mississauga, Ontario

Canada, L5T 1G1

For details on Telecor’s Return Policy, see our Published Merchandise Return Policy.

E:\VS-Care\VS-600 Manual.doc/AD

reproduced in any form, or by any means, without the prior written permission of Telecor Incorporated.

Telecor Inc. makes no representation of warranties with respect to this manual. Further, Telecor reserves

the right to make changes in the specifications o f the products described in this manual at any time

without notice, and without obligation of Telecor to notify any persons of such revisions or changes.

Windows XP and Windows Vista are Registered Trademarks of Microsoft in the United States and other

countries.

www.telecor.com

FCC Notice

PRODUCT NAME: VS-600 Resident Unit (VS-600)

FCC Registration Number: R73ERS001

PRODUCT NAME: VS-600 Wireless Pendant (VS-600-WP)

FCC Registration Number: R73ERS002

PRODUCT NAME: VS-600 Wireless Pull Cord (VS-600-WC)

FCC Registration Number: R73ERS003

FCC RULES: THIS PRODUCT HAS BEEN TESTED TO COMPLY WITH FCC PART 15,

SUBPART B, CLASS B – UNINTENTIONAL RADIATORS

OPERATING ENVIRONMENT: FOR USE IN RESIDENTIAL AREAS

FCC Compliance Statement:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference and (2) this device must accept any interference

received, including interference that may cause undesired operation.

FCC Notice:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a residential environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications.

FCC Warning:

Warning: The user is cautioned that changes or modifications to the unit, not expressly approved by the

manufacturer, could void the user’s FCC or other authority to operate the equipment.

The Party Responsible for Product Compliance:

Telecor Inc.

1114 Westport Crescent

Mississauga, Ontario

Canada, L5T 1G1

TABLE OF CONTENTS

A. Introduction........................................................................................................... A-1

A.1 VS-600 Resident Unit Overview........................................................................A-1

A.2 Overview of Peripheral Devices.........................................................................A-2

B. VS-600 Programming ........................................................................................... B-1

B.1 Resident Unit Diagnostic Procedure..................................................................B-1

B.2 Configuring the Resident Unit for Programming................................................B-2

B.3 Using Resident Unit Configuration Software .....................................................B-2

B.3.1 Options Tab............................................................................................B-3

B.3.1.1 Numbers Tab ......................................................................................B-3

B.3.1.2 Supervision Numbers Tab...................................................................B-4

B.3.1.3 Misc. Tab.............................................................................................B-5

B.3.2 Saving Programming Information to a File..............................................B-5

B.3.3 Prog./Config. Tab....................................................................................B-6

B.3.4 Wireless Tool Tab...................................................................................B-8

B.3.5 Log File Tab............................................................................................B-9

B.4 Speech Param. Tab...........................................................................................B-9

B.5 Creating Dial Strings........................................................................................B-10

B.5.1 Default Dial String Table.......................................................................B-11

B.6 Configuring the Resident Unit for Common Areas...........................................B-12

C. Installation............................................................................................................. C-1

C.1 Installing Dome Lights...................................................................................... C-1

C.2 Powering Dome Lights ..................................................................................... C-3

C.3 Mounting the Power Supply Unit ...................................................................... C-4

C.3.1 Book Mount Installation.......................................................................... C-4

C.3.2 Picture Mount Installation....................................................................... C-5

C.4 Connecting PSU to Resident Units to Power Dome Lights............................... C-6

C.5 Installing the Wired Pull Cord Station............................................................... C-7

C.6 Enabling Wireless Pendant or Wireless Pull Cord Operation ........................... C-7

C.7 Wiring a Smoke Detector.................................................................................. C-8

C.8 Wiring and Mounting Resident Unit.................................................................. C-9

VS-600 Resident Unit Manual A-1

A. Introduction

This manual describes the VS-600 Resident Unit and the peripheral devices available for use

with it. It explains the diagnostic procedures and programming steps that must be completed

prior to installation.

A.1 VS-600 Resident Unit Overview

The VS-600 Resident Unit is designed to allow hands-free and two-way communication between

the resident and an attendant. The Unit includes a Call Button to initiate calls to a designated

administrative staff location, a Call Cancel Button, a Volume Control, and Menu and Activity

Information Buttons. A built-in jack provides the ability to plug in a call cord, allowing the

resident to remotely initiate a call from the bedside.

Resident Unit (front

view)

The Unit is equipped with four status LEDs: Line, Activities, Menu, and Fault. The Line LED

illuminates when a call is initiated from the unit. When it illuminates in conjunction with the

Fault LED, it indicates a fault in the line. The Activities LED flashes when the Activities button

is pressed, and the Menu LED flashes when the Menu button is pressed to confirm selection.

The Fault LED illuminates and the unit signals a tone over the speaker to indicate a possible fault

in the Unit or the need for battery replacement.

The Unit can receive and decode signals from Wireless Pendants and Wireless Pull Cord Stations

and initiate calls to a designated administrative staff location. Each Pendant and Pull Cord

Station transmits a unique digital signal known only to the VS-600 Unit in the resident's room.

This provides assurance as to the exact origin of the call. The VS-600 has a reception range of up

to 50 feet (line of sight) from the Pendant or Pull Cord Station.

The Unit has an input provision for the connection of an external call-in device such as a Wired

Pull Cord Station, which provides call capabilities from resident bathrooms and showers. The

input can be assigned to one of six priority levels to clearly identify the origin of the call and

distinguish it from a cord call or a call initiated from the Unit’s call button.

With the addition of a Dome Light Module, the Unit has the ability to connect to a Dome Light

outside the resident's door, providing visual indication to staff of calls originating from the

resident's room. The Dome Light consists of three individual and different-colored lamps that

illuminate in distinct patterns to identify priority and the call-in device that the call originated

from.

A-2 Introduction

The Resident Unit is line powered from the single line station ports, eliminating the need for an

external power supply. The Unit is designed for installation into a standard 3-gang electrical

back box with 3-9/32" mounting centers.

A.2 Overview of Peripheral Devices

Described below are the peripheral devices that can function with the Resident Unit.

Wireless Pendant

The Wireless Pendant is worn by a VS-600 Resident user to allow him or her to

move freely about a room yet have the ability to place a call. Calls are initiated

by pressing a red call button on the Pendant.

Wireless Pull Cord Station

The Wireless Pull Cord Station offers the VS-600 Resident user the flexibility

of being able to position a Pull Cord Station anywhere in the room. This makes

it ideal for strategically positioning near furniture or in a bathroom or shower. It

makes it a cost effective "Add on" to the system without costly installation or

wiring upgrades.

Calls are initiated by pulling on the nylon pull cord. A call assurance LED

illuminates briefly and a soft tone sounds at the Station to confirm the

placement of the call. The call can be canceled at the Station by pressing a cancel button. An

illuminated LED and a tone at the Station confirm the cancellation of the call.

The Wireless Pull Cord Station is suitable for surface mounting directly to a wall. No backbox or

special mounting hardware is required.

NC-C1 Call Cord

A traditional Call Cord that plugs into the VS-600 Resident Unit to

provide the convenience of being able to initiate a call remotely from a

bedside.

Wired Pull Cord Station

The Wired Pull Cord Station provides call capabilities from resident

bathrooms and showers. The Station connects to the input on the VS-600

Resident Unit. Calls are initiated by pulling on the Station’s nylon call

cord, and annunciate at the attendant's telephone with a unique call priority.

The call can be canceled at the Resident Unit or from the attendant's

telephone.

VS-600 Resident Unit Manual A-3

NC1-LD3 Dome Light

The Dome Light is typically located outside the door of a room containing a

VS-600 Resident Unit to provide a visual indication of calls originating

from within the room. When a resident initiates a call, a LED in the Dome

Light illuminates. The Dome Light contains three LEDs with white, red and

green filters. Each lamp color represents a different call type that originates

from the Resident Unit’s call button or call cord, a Pull Cord Station, or a

Pendant.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Telecor Konferenzsystem Handbücher

Telecor

Telecor TMS-MA Bedienungsanleitung

Beliebte Konferenzsystem Handbücher anderer Marken

Kramer

Kramer VIA GO Bedienungsanleitung

AVT

AVT MAGIC AC1 Go Bedienungsanleitung

ProSoft Technology

ProSoft Technology AN-X4-AB-DHRIO Bedienungsanleitung

Sony

Sony PCS-I150 Bedienungsanleitung

Middle Atlantic Products

Middle Atlantic Products VTC Series Bedienungsanleitung

Prentke Romich Company

Prentke Romich Company Vanguard Plus Leitfaden

Speakerbus

Speakerbus iD 712 Bedienungsanleitung

Trelleborg

Trelleborg SafePilot CAT PRO Bedienungsanleitung

Sennheiser

Sennheiser ADN Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 7100 Bedienungsanleitung

AINA

AINA PTT Voice Responder Bedienungsanleitung

Yamaha

Yamaha ProjectPhone PJP-100H Bedienungsanleitung

vissonic

vissonic VLI Series Bedienungsanleitung

Panasonic

Panasonic KX-VC500 Bedienungsanleitung

Poly

Poly Trio 8300 Bedienungsanleitung

Crestron

Crestron Mercury CCS-UCA-SMK Maßzeichnung

Inmarsat

Inmarsat mini M Bedienungsanleitung

Tenveo

Tenveo ALL-IN-ONE Bedienungsanleitung