Teledyne Lecroy OC1021-A Montageanleitung

PN LEC4450 Rev A

Assembly Instructions and User’s Manual

OC1021-A Instrument Cart

Large Hex Wrench (5/32)

2 Knobs

6 Rods

2 Long Screws

14 Short Screws

2 Shoulder Screws

6 Plastic Washers

16 Large Lock

Washers

2 Metal Washers

2 Wing Nuts

4 Set Screws

Small Hex Wrench (1/8)

4 Small Screws

4 Small Lock

Washers

2 Posts

1 Support Bar

1 Retaining Bar

1 Bottom Tray

1 Top Shelf

2 Legs

2 Straps

Note: Correct installation of Set Screw

and Long Screw necessary for proper

performance of cart.

Illustration 1: Loosely preassemble 2 Rods and all Shoulder Screws, Knobs, Plastic Washers, and Metal Washers to the Top

Shelf using the placement as shown. Use the small wrench to insert the Set Screws into the Rod through the Top Shelf.

Illustration 2 and 3: Slide the assembly to the end of the Posts and tighten the knobs.

Plastic Washers

Metal Washer

Plastic Washer

2 Knobs

2 Rods 2 Shoulder

Screws

4 Set Screws

2 Metal

Washers

6 Plastic

Washers

Small Wrench

2 Rods

4 Short

Screws

4 Large

Lock Wash-

ers

Illustration 4: Loosely preassemble the Support Bar, Short Screws, Rods and Large Lock Washers as shown.

Illustration 5 and 6: Orientate the Support Bar to the Top Shelf using the two slots as shown, and slide it a few inches below the

Top Shelf. Lightly tighten screws.

Large Wrench

Illustration 7 and 8: Firmly tighten the Leg to the Bottom Tray with the Small Screws and Small Lock Washers as shown.

4 Small

Screws

4 Small Lock

Washers

Small Wrench

Illustration 9: Loosely preassemble the two Long Screws and two Rods with Large Lock Washers to the Legs.

Illustration 10: Orient the nonlocking caster and the slots in the Top Shelf and slide the Leg and Tray Assembly onto the Posts.

Illustration 11: Fit the Long Screws into the mating hole inside the Posts, lightly tighten the screw ensuring it has correctly

engaged the hole.

2 Rods

2 Large Lock

Washers

2 Long

Screws

Large Wrench

Illustration 12: Firmly tighten the 4 Short Screws and Large Lock Washers into the Bottom Tray as shown.

Illustration 13: Firmly tighten the 6 Short Screws and Large Lock Washers into the Legs as shown.

Illustration 14: Carefully stand the cart upright as it will sway somewhat. Adjust the Support Bar so that the bottom is 15.5” from

the Bottom Tray, ensure that the cart is vertical, then rmly tighten the screws on the Support Bar. Adjust the Top Shelf to the topof

the Posts, rmly tighten the 4 Set Screws, Knobs, Shoulder Screws, and the 2 Long Screws in the Legs.

12 14

15.5”

10 Large

Lock Wash-

ers

10 Short

Screws

Small Wrench

Large Wrench

2 Wing Nuts

Illustration 15: The Retaining Bar attaches to the Top Shelf in one of two places. Measure the scope from the front to the front

most feet and rmly tighten the bar in the appropriate position with the Wing Nuts. Strap the scope to the cart using the front

most slot and one of the two rearmost slots on the Top Shelf.

Illustration 16: Loosen the Knobs, tilt the Top Shelf to the desired position, and then tighten the Knobs to secure the Top Shelf.

15 16

2 Straps

Slots

Beliebte Outdoor-Wagen Handbücher anderer Marken

Costway

Costway TH10057 Bedienungsanleitung

Vivo

Vivo CART-PC02S Bedienungsanleitung

Ergotron

Ergotron STYLEVIEW SV42-3162-1 Bedienungsanleitung

VEVOR

VEVOR SC01 Bedienungsanleitung

Carts Vermont

Carts Vermont 20 Bedienungsanleitung

Vivo

Vivo CART-PC01 Bedienungsanleitung

Costway

Costway TL0400 Bedienungsanleitung

XPOtool

XPOtool 30261 Bedienungsanleitung

Branick

Branick 130 Gebrauchs- und Pflegehandbuch

Anthro

Anthro PrinterCart Bedienungsanleitung

Westward

Westward 2CZY4 Service-Handbuch

Hupfer

Hupfer TTW/V Bedienungsanleitung

Gorilla Carts

Gorilla Carts GCR-10P Bedienungsanleitung

Numatic

Numatic EcoMatic EM-5 Bedienungsanleitung

Bosch

Bosch XL-Cart Montageanleitung

Tennsco

Tennsco Modular Cart Top Component Assembly Bedienungsanleitung

Makita

Makita DCU601 Bedienungsanleitung

Clam

Clam POLAR TRAILER HD MAX Bedienungsanleitung