Teledyne Flir Saros DM Series Bedienungsanleitung

427-0200-01-10 Rev 120

June 2021

This document does not contain any export-controlled information.

Saros™ PTZ

DM-Series Camera

Quick Install Guide

1 Check Contents

Make sure all of the items above are included in the camera kit.

This camera is a Class 1 Laser Product

that complies with IEC 60825-1:2014.

Caution

Use of controls or adjustments or performance of procedures other than those

specified herein may result in hazardous radiation exposure.

Attention

L'utilisation des commandes ou reglages ou l'execution des procedures autres

que celles specifiees dans les presents exigences peuvent etre la cause d'une

exposition a un rayonnement dangereux.

427-0200-01-10 Rev 120

June 2021

This document does not contain any export-controlled information.

2 Prepare to Install the Camera

2.1 Install FLIR Discovery Network Assistant

Download the FLIR Discovery Network Assistant (DNA) tool to a computer on the

same VLAN to which you will connect the camera, and then unzip the file. The

DNA tool does not require a license to use and is a free download from

www.teledyneflir.com > Products > Security > Thermal Security Cameras > Saros

DM-Series.

2.2 Perform a Bench Test (Optional)

You can test the camera or configure it for networking before mounting it. Follow

the instructions in 3.4 Connect the Camera and 4.1 Configure for Networking, and

then continue with 2.3 Select a Location.

2.3 Select a Location

Select a suitable location to mount the camera.

For advice on positioning and orienting the camera, see the camera's installation

and user guide.

Verify that the operating temperature range is between -40° ~ 55° C (-40° ~ 131°

F), 10-90% relative humidity (non-condensing).

For the list of mounting accessories available for the camera, see the FLIR

Security Cameras - Accessory Guide.

3 Install the Camera

3.1 Fit Mounting Hardware

If required, install the mounting hardware for the camera according to the

instructions in the camera's installation and user guide.

3.2 Route Network and Power

Properly install the power and network cabling in the mounting hardware so that it

is accessible when the camera is mounted.

Power: Universal Power over Ethernet (PoE) 60W 4 pair forced mode, 24 VAC,

or 30 VDC.

Ethernet: Cat5e or Cat6 cable. Ethernet is required for streaming video and

configuring the camera.

3.3 Mount and Secure the Camera

Mount and secure the camera according to the instructions in the camera's

installation and user guide.

427-0200-01-10 Rev 120

June 2021

This document does not contain any export-controlled information.

3.4 Connect the Camera

Connectors

Connector

Connection

UPOE

Attach a Cat 5e or Cat 6 cable from the network switch

to the RJ45 connector for a 10/100/1000 Mbps Ethernet

and PoE connection. If using PoE, use a FLIR CP-POE-

4P-60W-xx injector or a switch that supports Universal

PoE 60W 4 pair forced mode. For more information

about compatible injectors and recommended switches,

contact Teledyne FLIR support. Verify that the UPOE

connector LEDs are steady green and flashing yellow.

AC24V

(DC30V) IN

If using a 24 VAC or 30 VDC power supply, connect it to

the three-pin power terminal block plug according to the

pin assignment shown.

DEFAULT

To reset factory defaults at any time, press the Default

button for at least 20 seconds.

14-pin

terminal

block

Attach wires from external alarm and audio I/O devices

to the 14-pin alarm/audio I/O terminal block plug

according to the pin assignment shown.

3-Pin Power

Terminal Block

24 VAC

30 VDC

L (Live; white; positive)

Pins 1 and 3

(polarity N/A)

Ground (Earth)

N (Neutral; black; negative)

427-0200-01-10 Rev 120

June 2021

This document does not contain any export-controlled information.

14-Pin Alarm/Audio I/O

Terminal Block

Definition

Audio-Out

Not used

Ground (Audio I/O)

Alarm-In 4

Alarm-Out A1

Alarm-In 3

Alarm-Out A2

Alarm-In 2

Alarm-Out B1

Alarm-In 1

Alarm-Out B2

Ground (Alarm I/O)

Not used

Audio-In

Warning!

This product contains a battery that is soldered to the PCB.

There is a risk of explosion if the battery is replaced by an

incorrect type. Do not replace the battery. The battery

should be disposed of in accordance with the battery

manufacturer’s instructions.

4 Configure the Camera

You can configure the camera using the DNA tool, the camera's web page, or a

VMS.

DNA tool

Camera's web page

Discover camera IP address

•

Configure IP address, mask, and gateway

•

Configure DNS settings, MTU, and Ethernet speed

•

Change user credentials

•

Configure more than one camera at the same time

•

For more information about using a VMS to configure one or more cameras at the

same time, see the VMS documentation.

4.1 Configure for Networking

By default, DHCP is enabled on the camera and a DHCP server on the network

assigns the camera an IP address. For example, if the camera is managed by a

FLIR Horizon or Meridian VMS and the VMS is configured as a DHCP server, the

VMS automatically assigns the camera an IP address.

If the camera is managed by a FLIR Latitude VMS or is on a network with static IP

addressing, you can manually specify the camera’s IP address using the DNA tool

or the camera's web page. The camera's default IP address is 192.168.0.250.

To configure the camera for networking using the DNA tool:

a. Make sure the camera and the PC are on the same LAN segment.

b. Run the DNA tool (DNA.exe) by double-clicking .

427-0200-01-10 Rev 120

June 2021

This document does not contain any export-controlled information.

The Discover List

appears, showing

compatible

devices on the

VLAN and their

current IP

addresses.

In the DNA Discover List, verify that the camera's status is Online.

If this is the first time you are configuring the camera or if it is the first time after

resetting the camera to its factory defaults, DNA automatically authenticates

the camera with the default password for the camera's admin user (admin).

If the admin user password has been changed, authenticate the camera.

In the DNA Discover List, right-click the camera and select Login.

In the DNA - Login window, type the password for the admin user. If you do

not know the admin user password, contact the person who configured the

camera's users and passwords.

Click Login, wait for Ok status to appear, and then click Close.

In the DNA Discover List, verify that the camera's status is Authenticated.

d. Change the camera’s IP address.

Right-click the camera and select IP

Setup.

In the DNA - IP Setup window, clear

Use DHCP and specify the camera's IP

address. You can also specify the Mask

(default: 255.255.255.0) and Gateway.

Then, click Update, wait for Ok

status to appear, and then click Close.

To configure the camera for networking using the camera’s web page:

a. Open the camera’s web page by double-clicking the camera in the DNA

Discover List or by typing the camera’s IP address in a web browser’s address

427-0200-01-10 Rev 120

June 2021

This document does not contain any export-controlled information.

bar. The camera's web page supports Google Chrome®and other popular web

browsers.

b. On the login screen, type admin

for the user name and the

password for the admin user

(default: admin).

c. When logging in to the camera for the first time or for the first time after

performing a factory default, specify a new password for the admin user.

Note

Use a strong password consisting of at least 12 characters and

at least one uppercase letter, one lowercase letter, and one

number. Passwords can include the following special

characters: |@#~!$&<>+_-.,*?= .

Log back in with the new password.

The camera's View Settings Home Page opens.

d. Click System Settings.

Make sure the Network page appears.

427-0200-01-10 Rev 120

June 2021

This document does not contain any export-controlled information.

e. You can select Static and manually specify

the camera's Hostname, IP address,

Netmask, and Gateway. You can also

specify the DNS Mode, Name Servers,

MTU (maximum transmission unit), and

Ethernet Speed.

f. Click Save. If you have made any changes on the Network page, the camera

reboots.

Note

For more information about configuring the camera for networking,

see the camera’s installation and user guide.

4.2 Attach the Camera to a Supported VMS

After you have mounted the camera and discovered or defined its IP address, use

VMS Discovery/Attach procedures to attach the camera to a supported VMS.

427-0200-01-10 Rev 120

June 2021

This document does not contain any export-controlled information.

5 Camera Dimensions

Following are the Saros PTZ DM-Series camera’s dimensions.

Front View

Side View

6 Register the Product

For warranty information, see https://www.teledyneflir.com/support-

center/warranty/security/flir-security-product-warranties/.

7 Contact Information

Teledyne FLIR LLC

6769 Hollister Avenue

Goleta, CA 93117

USA

Support: https://support.flir.com/

Corporate Headquarters

27700 SW Parkway Ave.

Wilsonville, OR 97070

USA

Inhaltsverzeichnis

Andere Teledyne Digitalkamera Handbücher

Teledyne

Teledyne Piranha4 Bedienungsanleitung

Teledyne

Teledyne Piranha4 Bedienungsanleitung

Teledyne

Teledyne PIXIS Bedienungsanleitung

Teledyne

Teledyne Princeton Instruments Quad-RO Benutzerhandbuch

Teledyne

Teledyne USB VISION BLACKFLY S Bedienungsanleitung

Teledyne

Teledyne EV71YC4MNT4005-BA0 Bedienungsanleitung

Teledyne

Teledyne Triton FH Series Bedienungsanleitung

Teledyne

Teledyne Linea CL LA-CM-08K08A Bedienungsanleitung

Teledyne

Teledyne Spyder3 SC-34-02K80-00-R Bedienungsanleitung

Teledyne

Teledyne Princeton Instruments PI-MAX 3 Benutzerhandbuch

Teledyne

Teledyne Genie Nano-5G Series Bedienungsanleitung

Teledyne

Teledyne FLIR Ariel CM-3202-11-I Bedienungsanleitung

Teledyne

Teledyne Princeton Instruments PI-MTE Benutzerhandbuch

Teledyne

Teledyne TS-M4096 Bedienungsanleitung

Teledyne

Teledyne Princeton Instruments Nano-XF Benutzerhandbuch

Teledyne

Teledyne Falcon4 57M Bedienungsanleitung

Teledyne

Teledyne DALSA Piranha 2 P2-2x-40 Series Bedienungsanleitung

Teledyne

Teledyne PIXIS-XF Benutzerhandbuch

Teledyne

Teledyne NIRvana System Bedienungsanleitung

Teledyne

Teledyne Genie Nano-10G Series Bedienungsanleitung

Teledyne

Teledyne Princeton Instruments PICam 5.x Bedienungs- und Wartungshandbuch

Teledyne

Teledyne 4M Bedienungsanleitung

Teledyne

Teledyne QuantaPro CP-10-04M02-50-L Bedienungsanleitung

Teledyne

Teledyne Kuro Bedienungsanleitung

Beliebte Digitalkamera Handbücher anderer Marken

Mercury

Mercury 350K Bedienungsanleitung

Pentax

Pentax Optio LS 465 Bedienungsanleitung

Sanyo

Sanyo VPC-S1085 Bedienungsanleitung

GE SMART A1255 Bedienungsanleitung

Point Grey

Point Grey Gazelle Bedienungsanleitung

Nikon

Nikon COOLPIX A Bedienungsanleitung

Pentax

Pentax P-5 Bedienungsanleitung

BlazeVideo

BlazeVideo A280 Bedienungsanleitung

Sony

Sony MCA-20 Bedienungsanleitung

Sony

Sony Alpha DSLR-A290 Bedienungsanleitung

ATIK Cameras

ATIK Cameras One Bedienungsanleitung

CohuHD Costar

CohuHD Costar 3930 Series Bedienungsanleitung

Leica

Leica M10-R Bedienungsanleitung

FujiFilm

FujiFilm FinePix A700 Bedienungsanleitung

Lorex

Lorex LNZ81P25 Series Bedienungsanleitung

GE J1470S Bedienungsanleitung

Sony

Sony A6700 Benutzerhandbuch

Canon

Canon EOS ELAN7 Bedienungsanleitung